Kyocera iBurst IUD19AC User manual

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 1 -
HiraoYamamotoKoyama
Designed
Checked
Approved
Feb
.
17
.
2009
Date:
1
.02
Revision:
Q
S13
T
-
EE
-
00
1
Reference:

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 2 -
Revision Record
Revision
Author Date Detail
1.00 Hirao May.10.2006 First Release
1.01 Miyasaka June.08.2006 Correct some writings
1.02 Honma Feb.17.2009 Add FCC Part24 required information
AC/DC Adaptor Update
The description of UTU is deleted

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 3 -
CONTENTS
Safety Precautions on iBurst Terminal.......................................................................4
Chapter 1 Introduction...............................................................................................8
Components List.....................................................................................................................................9
Pictures of Accessories.............................................................................................................................9
Outlook of iBurst Terminal ....................................................................................................................10
Indicators.............................................................................................................................................11
Requirements on your PC......................................................................................................................12
Outlook to use the iBurst Terminal.........................................................................................................12
Chapter 2 Setup Procedure....................................................................................... 13
iBurst Software Installation............................................................................................................... 14
Installation for Windows XP...................................................................................................................14
Installation for Windows 2000................................................................................................................17
Installation for Windows Me ..................................................................................................................20
Installation for Windows 98SE...............................................................................................................39
Installation for Mac OS X ......................................................................................................................59
Connection Establishment ................................................................................................................. 63
Connection Establishment for Windows XP.............................................................................................63
Connection Establishment for Windows 2000/Me/98SE.............................................................................68
Connection Establishment for Mac OS X.................................................................................................70
Chapter 3 Utility Software ....................................................................................... 74
Using Utility Software........................................................................................................................ 75
Using Utility Software for Windows........................................................................................................75
Using Utility Software for Mac OS X ......................................................................................................81
Status Indication over Ethernet ........................................................................................................ 88
Chapter 4 MTU Optimizer Software & Network Property......................................... 93
MTU Optimizer Software & Network Property................................................................................ 94
Chapter 5 Uninstallation.......................................................................................... 97
iBusrt Software Uninstallation.......................................................................................................... 98
Uninstallation for Windows XP/2000.......................................................................................................98
Uninstallation for Windows Me/98SE....................................................................................................101
Uninstallation for Mac OS X................................................................................................................108
Chapter 6 Trouble shooting......................................................................................110
Windows..............................................................................................................................................111
USB connection with Windows Me/98SE............................................................................................... 111
Illegal hang-up when install iBurst Terminal......................................................................................... 114
Illegal hang-up when set up dialer........................................................................................................ 116
PC hang-up when eject iBurst Terminal from Win98 USB port................................................................ 118
Mac......................................................................................................................................................119
Data rate............................................................................................................................................ 119
Chapter 7 Information............................................................................................ 120
FCC Compliance Statement............................................................................................................. 121
FCC RF Radiation Exposure Statement......................................................................................... 122

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 4 -
Safety Precautions on iBurst Terminal
Things you must know
When using the product, use it correctly according to the safety precautions.
The product uses particular radio frequency band tuned for the network operator.
The safety precautions, hardware, software, and the design of the product may be changed
in the future without any announcement to the customers.
About use restriction
The product is designed as an OA apparatus for home use. Please use it neither in the
medical apparatus directly to affect a human life, nor the system of which very high
reliability is required.
Do not use the product in the zone where the wireless machines are forbidden, such as an
airplane and a hospital. An electric device and medical apparatus are affected and it
becomes the cause of the accident.
About Qualification
Our company does not take any responsibility about the damage produced by use under
the conditions such as natural disasters, earthquake, flood, fires, misuse by intent or
carelessness or other than the responsibility of our company.
Our company does not take any responsibility about the damage produced by external
factor, failure, malfunction, and fault of product, such as loss of enterprise profits,
enterprise discontinuation, change and disappearance of the contents of memory etc.
Our company takes no responsibility about the damage produced by not keeping the
written contents of an owner's manual.
Our company takes no responsibility about the damage produced from incorrect operation
in combination with the connection apparatus and software in which our company is not
participating etc.
iBurst ™ is a registered trademark ofArrayComm, Inc.
Mac OS X is a registered trademark ofApple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation.
In addition, the name of the software carried in this document and peripheral equipment is
each company’s trademark, or a registered trademark.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 5 -
For your safety
-------- Danger --------
( If used improperly, may cause death or serious injury. )
Do not use with an abnormal condition, such as with emission of smoke or odor. It may
cause fire or electric shock.
Do not insert metal or flammable materials into the product interior through the air vents.
Pull out power plug from the outlet in case that foreign material into the product interior.
It may cause fire or electric shock.
Do not disassemble or remodel the product. It may cause fire or electrical shock.
Do not use or place the product at places with high humidity such as in the bath room or
near the humidifier. It may cause fire or electric shock. And do not touch the product with
wet hands.
Do not use the product with power supply other than AC100 to 240V. It may cause fire or
electric shock.
Do not plug too many leads into a single socket with extensions such as table taps, divided
outlets, and divided sockets. It may cause fire or electric shock. Moreover, make sure that
the total current does not exceed the capacity of the power supply. Otherwise, may cause
fire or electrical shock.
Do not damage, break, modify, bend, pull, twist, or bundle the AC cord. In addition, if a
heavy material is placed onto the cord or it is heated, the cord may break and cause fire or
electric shock.
Securely insert the plug into the outlet. If a metal object edges the teeth of the plug, it may
cause fire or electric shock. When pulling out the plug from the outlet, be sure to hold onto
its head. Pulling the cord can damage itself.
When you change the installation place of the product, pull out the plug from the outlet
and confirm that PC is completely separated from it. Otherwise, the cord may be damaged
and cause electric shock or fire.
Before inserting the plug into the outlet, check that there is no dust on its edge and head.
As dusts can easily enter between the plug and the outlet, they may cause fire or electric
shock. Pull out the plug from the outlet, at least once in a half year or a year, and
clean/maintenance.
Use the AC/DC adapter enclosed with the product. Usage of other AC/DC adapters may
cause fire or electric shock.
Do not place things or put cloth on the top of the plug. It may heat and break the plastic
and/or the rubber, causing fire or electric shock.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 6 -
------- Warning --------
( If used improperly, may cause disability or physical damage. )
Do not give a shock strong against the product, such as dropping and throwing. It becomes
the cause of failure. Moreover, do not ride on the product. It may become the cause of an
injury.
Do not put the product under direct sunshine or near equipment with high temperature
such as a stove and a heater. It may raise the temperature of the interior and cause fire.
Do not put the product at places with an extreme fluctuation of temperature, such as near
the air conditioner or a heater. The dew condensation may occur in the interior and cause
fire, electrical shock, and malfunction.
Do not put the product at places with oil and steams such as in the kitchen. In addition, do
not put it at dusty places and places where metal powder and toxic gas occur. It may cause
fire or electric shock.
Do not place the product on unstable places such as on an unsteady desk or slanted
surfaces. In addition, do not put any object on the product. It may loose balance and
tumble, or fall and cause injury.
When the thunder occurs in near, do not use the product and its peripheral equipment. It
may become the cause of an electric shock.
If the air vents are blocked, the interior may be heated and cause malfunction. Please do
not use the products in the following manners;
Put on carpet or bedclothes.
Cover with tablecloths.
Put at places with bad ventilation, such as on a book shelf, in the drawer, or in the
closet.
If suspending the use for a long time, pull out the plug from the outlet.
Do not use the AC cord with an extension cord. It may cause fire.
For maintenance, pull out the AC plug from the outlet for safety. Do not wipe the product
with benzene, thinner, or alcohol. It may cause the product to decolorize or deform. If the
product be stained, put some neutral detergent on a dry cloth and wipe gently.
Do not connect electricity supplied LAN cable to the product. It may cause smoke or fire.
Do not touch the connector pins directly with your hands. Static electricity may affect the
components. As static electricity is created from both the cloth and the human body, before
putting or removing the product, release static electricity by touching a metal object such
as a small cabinet.
Do not use it in the intense place of vibration. It becomes the cause of failure.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 7 -
-------- Caution --------
( If treated improperly, the equipment may not perform or work properly. )
Do not put the product at low temperature. The product may not function properly.
Do not put the product on the top of magnetic objects and places where electromagnetic
waves occur. This includes electrical appliances, AV, and OA (microwave oven, speaker, TV,
radio, fluorescent light, inverter air conditioner, and electric kitchen appliances). The
product will not be able to make communication properly if effected by magnetism or
electronic noise. Putting the product near TV or radio may cause RF receive error.
The product lifetime may shorten if used at places with hydrogen sulfide such as at a hot
spring.
Data communication will be disabled or a data file may corrupt if the PC is turned off or
the product is separated from the PC during the communication. Important data must be
verified against the original data.
For fixing the product, use the enclosed fixture.
When connecting the product onto PC, use the enclosed USB cable or LAN cable.
Both a USB and an Ethernet interface cannot be used simultaneously in case a UTD
model.
When using UTD model, Please put the antenna at vertical position as shown in the below
diagrams so that the unit could acquire proper antenna characteristics.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 8 -
Chapter 1 Introduction
7
This chapter describes what should be confirmed before
using iBurst Terminal.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 9 -
Components List
The table below shows the list of components. Please confirm items in the package.
Component Notes Q’ty
iBurst Terminal Unit of UTD model
Refer to the pictures shown in next page. 1
AC/DC Adapter Input: 100 - 240V AC/ 50 - 60Hz/ 0.6A
Output: 9V DC/ 1.7A
Cable Length of output side: 2m
1
Power Cable Length: 2m 1
USB Cable Type: USB1.1
Length: 1m 1
10-Base-T Ethernet Cable Type: Straight through/ Category 5
Length: 2m 1
Pictures of Accessories
AC/DC Adapter

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 10 -
Outlook of iBurst Terminal
USB port
10Base-T port
only on UTD model
Back side view
Antenna
Power Indicator
Link/Communication Indicator
PC Connection Indicator
DC Power Input
Power switch

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 11 -
Indicators
The table below describes meaning of each indicator.
Indicator State Meaning
Power Indicator OFF Turned OFF
Blue Turned ON
Blinking
Fault
Link/Communication Indicator OFF Turned OFF
Amber No signal receiving
Yellow Weak signal receiving
Blinking when communicating.
Green Strong signal receiving
Blinking when communicating.
PC Connection Indicator OFF Any port not active
Amber USB port
Green 10Base-T port

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 12 -
Requirements on your PC
PC/AT Compatible PC with WindowsXP/2000/Me/98SE; or
version 10.1.5 or later version of Mac OS X except Mac Intel model.
1 USB1.1 port or a later version of USB port.
NOTE: In case of using USB connection.
1 10Base-T Ethernet port or compatible.
NOTE: In case of using 10Base-T Ethernet connection with a UTD model.
Outlook to use the iBurst Terminal
A UTD model has 1 USB port and 1 10Base-T Ethernet port. The USB port, or 10Base-T
Ethernet port, shall be connected with your PC. Before connecting the USB interface, you have to
install iBurst software which includes device drivers. If you want to utilize 10Base-T connection,
you don’t have to install the software in case Windows XP or Mac OS X. Please read through
every sections related with the operating system for details.
USB Connection
10Base-T Ethernet Connection
USB port
Back side of UTD
10Base
-
T port
USB Cable
Category 5 Cable
(Straight cable)

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 13 -
Chapter 2 Setup Procedure
This chapter describes how to install iBurst software, then
guides you how to make a network connection so as to use
data communication service.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 14 -
iBurst Software Installation
This section shows the procedure to install iBurst software on your PC for utilizing iBurst
Terminal. The procedure shall be done once before using it.
Installation for Windows XP
NOTE:
If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not
through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you
can skip this section and you need only to create a dial-up connection setting described at from
page 62. You can see indications of the iBurst Terminal over Ethernet. See page 87 for the
method.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 15 -
5. Select [I accept the terms the license agreement], click the [Next >] button.
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE: To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 16 -
8. The following dialog window will appear, and installation of software begins.
9. When the installing process finishes, the dialog window shown below will appear. Select “Yes, I
want to restart my computer now” and click the [Finish] button in the dialog window.
10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port.
The iBurst Terminal will be recognized and will be ready to use automatically.
NOTE: If the PC request to restart again, click [Yes] to restart the PC.
NOTE: To connect to the Internet, refer to page 62.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 17 -
Installation for Windows 2000
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
5. Select [I accept the terms the license agreement], click the [Next >] button.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 18 -
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE: To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.
8. The following dialog window will appear, and installation of software begins.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 19 -
9. When the installing process finishes, the dialog window shown below will appear. Select [Yes, I
want to restart my computer now] and click the [Finish] button in the dialog window.
10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port.
The iBurst Terminal will be recognized and will be ready to use automatically.
NOTE: If the PC request to restart again, click [Yes] to restart the PC.
NOTE: To connect to the Internet, refer to page 67.

iBurst Terminal, Desktop Model (UTD) Manual
Kyocera Corporation Revision 1.02 --- Feb.17.2009
- 20 -
Installation for Windows Me
Since the installation disk of Windows Me may be required while driver installation, please
prepare the CD or copy the CD into a hard disk in your PC for it.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
5. Select [I accept the terms the license agreement], click the [Next >] button.