La Toulousaine 7386 User manual

09/21
(Document reserved for installers)
This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.2
- Hammer drill
- Set of steel/concrete drill bits
- Electric screwdriver with end-pieces
- Allen keys + Flat wrenches
- Flat screwdriver 2,5 mm
- Wire stripper pliers
- Hammer/Chisel
- Spirit level
- Plumb bob
- Hacksaw
- Angle grinder
- Riveting pliers
- Tape measure
- Appropriate screws and
pins for the supports
- 10 mm shims
Required equipment........................................................................................................p.2
Installation instructions....................................................................................................p.3
Electrical duct installation................................................................................................p.4
Assembling + installing the aluminum posts (Option)......................................................p.4
Check of existing posts .........................................................................................p.5 to p.6
Guide rail attachment (on all types of posts)...................................................................p.6
Totem operator installation (on all types of posts).................................................p.7 to p.8
Installing the gate (on all types of posts)...............................................................p.8 to p.9
Finishing clips ...............................................................................................................p.10
Installing the opening stop ............................................................................................p.10
Installing the closing stop (on aluminum posts).............................................................p.11
Installing the closing stop (on existing posts)................................................................p.11
Receiver box adjustment...............................................................................................p.11
Setting the limit-switches...............................................................................................p.12
Connection plan ............................................................................................................p.13
DIPS switch factory settings..........................................................................................p.13
IMPORTANT : Flashing amber light and cells installation ............................................p.14
Outdoor antenna installation .........................................................................................p.15
Self-learning..................................................................................................................p.16
In case of a fault or before the self-learning cycle : Reset board .................................p.17
Radio receiver :
- Transmitter programming ..........................................................................................p.17
- Wireless keypad programming..................................................................................p.18
- Deleting a key from the transmitter............................................................................p.19
- Deleting a channel.....................................................................................................p.19
- Memory wipe.............................................................................................................p.19
Options :
- Connection : Pulse button .........................................................................................p.20
- Connection : Partial open button ...............................................................................p.20
- Connection : External antenna ..................................................................................p.20
- Connection : Battery..................................................................................................p.21
Breakdown assistance ..................................................................................................p.22
Description of LED flashing sequences.........................................................................p.22
Appendix ............................................................................................................ p.23 à p.24
In the case of an openwork gate ...................................................................................p.25

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.3
* Before beginning the assembly, read this manual carefully.
* This fence element must be installed by a professional technician.
* All the parts delivered are specifically sized for this product.
Adding and/or using other parts may be detrimental to safety and may affect
the product’s warranty.
* Any modification or improvement of this fence element must be compliant
with the standard EN 13241 + A2.
In this case, a "modification/transformation" file must be created by the installer
as per the standard EN 12635 annex C.
* Use the appropriate tools to install these products.
Ensure that the work is carried out on a stable floor.
* Ensure that the assembly area is clear, clean and clearly marked out.
* Ensure that no other people are present at the assembly site apart from the installers.
Non-authorized persons (children for example !) who are present at the site risk injury
during assembly.
*All the components of this fence element must be installed in compliance with the
installation instructions provided in this manual.
* All requirements of EN 13241 + A2 must be met and checked if necessary.
WARNING !
To ensure that this product is assembled,
used and maintained in complete safety, it is important
to follow the instructions provided in this document.
For everyone’s safety,
observe the following precautionary measures.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.4
Interior view
Operator power supply 230V 3x2,5 mm²
Totem operator
136 mm
Power output
136 mm
Operator positioning,
if opening to the left
Operator positioning,
if opening to the right
Clip
Remove clips
before the profiles are assembled
12
Assemble the profiles Assembled posts
3
243 mm
115 mm
243 mm
115 mm Power output
Totem operator
Profiles

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.5
Fill completely
Iron + Concrete framework
Overall height*
400 mm
400 mm
* Overall width and
height correspond to
the order dimensions.
Fill completely
Once the installation is complete, cut the attachment clips according to the height of the posts,
then click them onto the posts.
Please note :
Before installing the gate,
check that the concrete/post
is completely set
(21 days to dry on average).
Do not attach
the caps
It is essential to check
the plumb line of the posts
on all sides.
The 2 posts must be
at the same level
and correctly aligned.
Height Height
Width
Width
Check under hat :
Width between posts and height of posts
Checking worksite dimensions

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.6
Please note :
Ensure that the threshold is leveled correctly ;
If you feel the threshold is too irregular or
sloping, do it again.
Level line
Post at bottom of slope
Street
view
Straight post
Rail
50 mm
Street
view
Outward leaning post
Rail
50 mm
Street
view
Inward leaning post
Rail
50 mm
Closing post
Opening side
Attach the rail from the closing post ; Using the 8 mm pins and suitable screws (not supplied).
Opening post
Rail assembly
Junction pin

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.7
136 mm 136 mm
If left opening If right opening
+
+
Interior view
Fittings adapted to the support
Pins + Screws (not provided) Ø10 mm
Floor fittings
Trace the position of the anti
-vibration bearing plate then
remove the Totem operator
+
2
1
Permanently fix the Totem
operator on the ground
on the 3 fixing points
3
Remove the cap
Drill tracings
on the post
Anti-vibration plate attachment
Please note : Attach the Totem operator to a single point, so that it can be removed more easily later.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.8
Mount the cap and secure
it with the set screws
6
Attach the anti-vibration bearing
plate to the post
5
Ensure the Totem operator is plumb and fix
the adjustment screws of the bearing plate
4
Top view
Attach wheel covers
Wide head rivets
4,8x16 (provided)

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.9
Place the gate
- Gate open, press the rack and pinion on the sprocket so that the notches of the rack and pinion
coincide with the notches of the sprocket and lock the screw.
- Unwind the gate as you go until it closes and repeat the above step until all the rack and pinion
screws are tightened.
Sprocket
Rack and pinion
Lock the screw
Adjust the rack
Guiding
rail
- Place the gate on the guiding rail.
- Advance it towards the Totem operator to slide
the bearings into the gate’s transom guide rail.
- Check that the gate is plumb, adjust the guiding
bearings accordingly and lock them in place.
Guiding
bearings
Transom guide rail
Please note : Check that the operator is disengaged (clutch lever in down position).
Please note² : The height of the operator sprocket is preset at the factory.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.10
- Mount the finishing clips on the Totem operator.
- Cut the clip around the guide rollers.
Opening post
Opening stop
- Open gate to opening post.
- Position the opening stop on the floor.
- Attach it with suitable pins or screws (not provided).
Finishing clips
Installing the opening stop

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.11
Screws FHC M8x20 + Drilled square
(supplied)
Closing stop Stop support
Closing stop fastening
CHC screws M10x16 + M10 washer
(supplied)
Aluminum post
Receiving box
to be fixed with 2 screws
TH M8x25
+ M8 nuts + M8 washer
(supplied)
5 mm clearance
Front view
Installing the closing stop (on aluminum posts)
Installing the closing stop (on existing posts)
5 mm clearance
Closing stop
≈ 190 mm
Closing post
- Close gate to closing post.
- Position the closing stop on the post at the top
of the gate.
- Secure it with pins and screws suitable for the
support (not provided).
Top view
Receiving box
Adjustment
screw
- Adjust the receiving box in line with the gate using the 2 screws inside the closing stop.
Closing stop
Receiver box adjustment

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.12
Comment : If the cells are not installed, the wireless accessory management board will beep.
- Fix the magnet on its support with the TF 4,2x25 auto screws (supplied).
Please note : To adjust and fix the magnet support to the rack and pinion follow steps 2 and 3.
- Push the gate in the other direction (1) to position the right limit switch (2).
- Set the magnet support (3) on the sensor to switch (red LED lights up).
- Attach the magnet support to the rack and pinion with the 2 screws TF 4,2x16 (supplied).
3
Adjustment of the closing or opening limit-switch (depending on the operator side) :
- Open or close the gate (1) to position the left limit switch (2).
- Set the magnet support (3) on the sensor to switch (red LED lights up).
- Attach the magnet support to the rack and pinion with the 2 screws TF 4,2x16 (supplied).
2
Setting the limit-switches
Unlocking the operator
Magnet
Support
Auto screw
TF 4,2x25 1
Sensor
Operator board
Sensor
Operator board

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.13
Connection plan
2- Phase L1 (black)
3- Neutral N (blue)
5- Earth (green/yellow)
Power supply 230V
DIPS switch factory settings
- Position switch 7 according to the opening direction.
- Check switch 8 whether it’s ON.
Switch ON OFF Description
1XHold to run mode deactivated
If ON : Hold to run mode activated
2 X
Reaction to input safety contact strip / switch-off
Partial reversal
If ON : Full reversal
3XLocked weight potentiometer
(Never switch to OFF)
4 X
Reaction of the cells during closure
Full reversal
If OFF : Partial reversal
5XSleep off
If OFF : Sleep enabled
6XThe triggering of the cells starts a time delay (gate open)
If ON : The gate closes 5 seconds after passing through the cells
7ON : Left opening gate (exterior view)
OFF : Right opening gate (exterior view)
8XON : Pre-alert timeout enabled
If OFF : Early warning time is disabled
Board (wireless accessory management)
Cells, 4 wires
Cells, 2 wires
Potential-free relay contact/max.24V CC/CA
STOP button
Gate button CLOSED
Pulse button
OPEN PULSE CLOSED STOP
Power supply, 4 wires
24V
warning light
Open button
partial/time delay
input
Emergency stop
push button
Partial opening
Please note : 20V output, terminals 8/10

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.14
1- Unscrew and remove the orange cover.
2- Unscrew and remove the board.
3- Place the batteries.
4- Screw the board and the orange cover back on.
5- Attach the flashing amber light assembly to the post.
Cover
Board
1- Install the batteries (the cell diode lights up for a few seconds and then turns off).
2- Insert the TX transmitter cell (green diode) and fix it.
3- Next, place the RX receiver cell (red diode) so that its LED lights up (cells aligned) and then fix it.
Please note : If after a few minutes the RX cell goes into standby, reactivate it : Remove the battery
and then put it back in (or press the alarm button) and repeat step 3.
Batteries Type C
LR14 / 1,5V
Please note : Wireless accessories are pre-programmed at the factory.
IMPORTANT : Flashing amber light installation
Installing the cells
TX : Transmitter cell
AA batteries
1,5V / LR6
Green LED
Red LED
Alarm button
Management board
(wireless accessories)
LED status
Must switch off
On
RX : Receiver cell

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.15
Outdoor antenna installation
Step 2 : Remove the built-in antenna on the MASTER control board.
Step 3 : Wire the outdoor antenna to the MASTER control board.
5 mm
15 mm
- Strip the outdoor antenna cable.
- Twist the strands together.
- Cut off the protruding strands.
- Connect the outdoor antenna cable :
Shield wire (outer braid) → to Mass.
Boundary wire (center wire) → to Ant.
Ant.
Mass
Step 1 : Installing the antenna.
- Mount the antenna on the bracket, following the mounting order as below.
- Fix the bracket to the Totem (screws to be adapted, not supplied).
- Pass the antenna cable through the cap openings in the back.
- Lower the cable inside the Totem and insert it into the box through the cable glands.
Assembly order

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.16
Lock the operator
1- First learning cycle :
Measuring distance (it will be done at reduced speed).
a) Press the START button, the gate moves to the opening limit
stop (opening limit-switch LED lights up).
Please note : If the gate closes, re-set the switch 7
(see chapter : DIPS switch settings).
b) Wait for validation click (◄ and ► turn on and off).
c) Press the START button, the gate moves to the closing limit
stop (closing limit-switch LED lights up).
d) Wait for validation click (◄ and ► turn on and off).
2- Second learning cycle :
Force measurement (slowing down at the end).
- Redo the same procedure : Follow the steps of the first
learning cycle (a, b, c and d).
Information : After the 2 learning cycles have been completed,
the "Light" LED must go out ; the learning cycle is completed.
Please note : If the "Light" LED stays on, repeat the entire
learning cycle again.
Please note : The learning cycles are in hold-to-run mode.
Please note² : Check that the LED "Light" is flashing,
if not flashing, reset the board.
(see chapter : Resetting the board).
Move gate to intermediate position
Self-learning
12
3

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.17
Please note : A reset is only possible when the operator is locked and the 230V voltage is present
(not possible on battery function).
- Press the START and PROG buttons
simultaneously and hold them down.
Please note : The "Light" LED starts flashing.
- Release the buttons while the "Light" LED is
still on.
- Reset is complete and the LED "Light" is
flashing.
1- Programming button.
2.1- LED radio channel 1 : Pulse mode
(Open - off - closed - off - open - etc…)
2.2- LED radio channel 2 : Partial opening
(Pedestrian opening)
2.3 and 2.4- LED radio channel 3 and 4 : Not used
- Press the programming button (1 time for channel 1, LED 2.1 lights up).
Please note : If LED 2.2, 2.3 or 2.4 lights up, continue to press until LED 2.1 is reached.
- Select a key on the transmitter and hold it down until LED 2.1 goes out.
- Programming in pulse mode is complete.
To program additional pulse emitters, repeat the above steps.
(112 memory entries are available).
Move gate to closed position.
Pulse mode
In case of a fault or before the self-learning cycle :
Reset board
Transmitter programming
Once the channel is selected, you have 10 seconds to perform the next
operation, otherwise the programming of the receiver will be cancelled.

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.18
(Factory default ≈ 20% of gate length)
- Press the programming button (2 times for channel 2, LED 2.2 lights up).
Please note : If LED 2.1, 2.3 or 2.4 lights up, continue to press until LED 2.2 is reached.
- Select another key on the transmitter (different from the pulse mode) and hold it down until
LED 2.2 goes out.
- Programming for partial opening is complete.
To program additional transmitters for partial opening, repeat the above steps.
Step 1 : Clear current value.
- Gate closed, press and hold down the PROG button + The programmed partial opening button
of the transmitter, for 2 seconds.
- The "Light" LED lights up.
- Release the keys, you hear a confirmation click.
- The opening recorded value is canceled.
Step 2 : Program the new desired opening distance.
- Press the same key (Partial open) on the transmitter, the gate will open.
- At the desired distance, press the (Partial open) button on the transmitter again, the gate stops.
- Press the (Partial open) button on the transmitter, the gate closes again and confirms the
opening distance.
To activate this mode : The pulse mode must be programmed or partial opening.
- Turn the potentiometer to the right until the desired
delay time.
Please note : Potentiometer turned to maximum
≈ Timer 5 minutes.
- Perform a validation cycle to check for proper
operation.
Please note : If the potentiometer remains on the
value 0, the gate will remain in
sequential operation for pulse mode
and partial opening.
- For the installation and programming of the keypad, see the instructions enclosed
in the accessories package, entitled : 10-function wireless keypad connection instructions.
Partial opening
Changing the partial opening distance
Automatic mode
Wireless keypad programming

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.19
- Press the programming button (1) and hold it
down for 5 seconds (one of the LEDS flashes).
- Release the programming button (1).
- Press a key of the transmitter to be deleted
(LED goes out).
- The deletion of a key is complete.
- Press programming button (1) and hold it down
after selecting the channel.
• 1 time for channel 1, LED 2.1 lights up :
Pulse mode.
• 2 times for channel 2, LED 2.2 lights up :
Partial opening.
Please note : If LED 2.3 or 2.4 lights up, continue
to press until LED 2.1 or 2.2 is reached.
- The LED flashes after 5 seconds and then lights
up after another 10 seconds.
- Release the programming button (1).
- Deleting a channel is complete.
- Press the programming button (1) and hold it
down.
- The LED flashes after 5 seconds, then lights up
after another 10 seconds and finally after 25
seconds all LEDS light up.
- Release the programming button (1).
- Memory wire is complete.
Non utilisés
Deleting a key from the transmitter
To remove all the keys from the transmitter,
repeat the steps below for each key.
Deleting a channel
Memory wipe

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. It may be modified at any time in accordance with product changes.
_N°7386Installation_Totem operator (Sliding gate)
09/21 p.20
Terminals 22 and 26
Terminals 11 and 13
Remove jumper
from pins Set jumper to "Pos 1"Plug the external antenna connector to "Pos 2"
1
Connection : Pulse button
Connection : Partial open button
Connection : External antenna
23