La Toulousaine 1033 Guide

N°1033
This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
Installation & Connection manual
06/20
(Document reserved for installers)
SAFETYBOX
Wall-mounted with European cylinder
Only for Axial operator
IP40 box :
- Electrical connection only for indoor installation.
If installed outdoors, use a control device such as a sealed key switch box.
- Connections must be made by authorized persons.
Wall-mounted box
Min. support = 120 x 60 mm
Dimensional characteristics

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
_N°1033
06/20 p.2
Installation & Connection_SAFETYBOX_Axial operator
Housing attachment
- Open the cover of the box
using one of the 2 keys
provided.
- Remove the lever and switch.
- Mark the position of the holes
by placing the housing against
the profile. The housing must
be mounted vertically, see
diagram opposite.
- Drill the holes.
- Feed the release cable
through hole A.
- Adjust the length of the
release cable sheath to your
installation. Make sure that
the cable sheath is in contact
with the housing.
- Pass the power cables
through the support and feed
them ut through the opening.
- Fix the release housing using
the holes B according to the
support (screw kit not
included)
A
Release cable
Power cable
B
B
B

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
_N°1033
06/20 p.3
Installation & Connection_SAFETYBOX_Axial operator
Cable clamp
screw
Release mechanism adjustment
- Pass the cable through the lever.
- Place the lever in its slot in the raised
engaged position.
- While pulling on the release cable, tighten
the STHC screw of the cable clamp firmly
(2.5 hexagon wrench).
- Check the release mechanism of the
operator by operating the release lever,
without forcing it.
- If necessary, adjust the tension of the
release cable by repeating the previous
steps.
- Cut off excess release cable, if necessary.
Release
lever
Electrical connection
IP40 box :
- Electrical connection only for indoor installation.
If installed outdoors, use a control device such as a sealed key switch box.
- Connections must be made by authorized persons .
Electrical wiring diagram
Connect the earth wire
(Green/Yellow)
to the earth screw of the box
Operator
Power supply
Joint box
SAFETYBOX
Phase (Red)
Neutral (Blue)
3 wires
2.5² 230V
Ascent phase (Black)
Descent phase (Brown)
1 2 3

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
_N°1033
06/20 p.4
Installation & Connection_SAFETYBOX_Axial operator
Earth wire
Test the controls
Release lever
Clamp screw switch
Switch
(Ascent/Descent)
Earth screw
Please note : If by pressing the ascent button,
the shutter goes down, reverse
phases 1 and 3.
Electrical connection
IP40 box :
- Electrical connection only for indoor installation.
If installed outdoors, use a control device such as a sealed key switch box.
- Connections must be made by authorized persons.
Earth

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
_N°1033
06/20 p.5
Installation & Connection_SAFETYBOX_Axial operator
Changing the cylinder
- Unscrew and keep the TF M5x12 screw and the fan washer that
holds the 30+10 cylinder .
- Install the 30+10 cylinder supplied as an accessory with the
countersunk screw and washer previously removed.
The cylinder opens with the product’s other cylinders.
TF M5x12 screw
M5 fan washer

This document is the exclusive property of FTFM La Toulousaine and must on no account be copied. The document may be modified at any time in accordance with product changes.
_N°1033
06/20 p.6
Installation & Connection_SAFETYBOX_Axial operator
Engagement procedure
- Engage the operator by raising the release lever.
- Check that the ascent and descent controls are functional.
- Shut the front of the box and turn the key to close the box.
Release mechanism
- Insert the key into the cylinder on the front of the box .
- Turn the key and open the front of the box.
- Pull the release lever to release the operator.
- Open the shutters manually.