Lagler ELAN User guide

ELAN
English / Englisch
EDGE-, STAIR- AND CORNER-SANDING MACHINE ELAN
Operation,
Maintenance, Safety
Translation of original operating instructions
for the edge-, stair- and corner-sanding machine
00.350.20.002 01.02.2013
*00.350.20.002*

ELAN 01.02.2013
English / Englisch
Motor
Attachment
Handle
Switch
MultiClip
Guide roller
Fig. 1: Main features of the edge-, stair- and corner-sanding machine ELAN
Dust bag
2
ELAN ASSEMBLY

ELAN 01.02.2013
English / Englisch
1. Introduction
You have purchased a high-quality product from LÄGLER®.
We wish you great success with your ELAN. This
machine was manufactured using the most modern
methods of production. All LÄGLER®products are subjected
to a thorough inspection before leaving the factory.
Please read these operating instructions carefully before
you start working with your ELAN for the first time.
These operating instructions include important information
on work safety and will give you answers to many
questions so that you can work with the machine safely
and without any problems. If you cannot find a specific
subject in this manual, please refer to your sanding
instructions manual or contact your local dealer. Your
local dealer is very familiar with the ELAN machine and
is a highly qualified expert trained by our company. Your
local dealer will provide you with the best possible advice
and support.
1.1 Features of the machine
In figure 1 (page 2), we have included the designations
of the most important components of the ELAN. Take
your time to become familiar with the machine.
1.2 Description of the machine
The ELAN stair-sanding, edge-sanding and corner-san-
ding machine works with a sanding disc on which Velcro
sanding discs can be fastened. Traditional sanding discs
fastened with a tensioning screw can, of course, also be
used. The work zone is protected by the attachment. The
fan housing, on which the electric motor is mounted in
vertical position, is located on the attachment. A motor
power supply cable is used to connect the machine to
the power supply system. The motor switch with ON / OFF
is located on the right side in the handle piece. The
machine is moved by means of two steering wheels at
the rear side of the machine. The handles are located on
top of the motor. The suction union piece, to which the
dust bag clamp and the dust bag are attached, is located
underneath the handles.
The ELAN can only be used for dry processing operations.
Never use the ELAN for wet processing operations (life-
threatening risk)!
Contents
1. Introduction 3
1 .1 Features of the machine 3
1 .2 Description of the machine 3
1 .3 Application 4
1 .4 Safety instructions 4
1 .5 Protective devices 5
2. Technical data 5
3. Getting started 7
3.1 Preparing the machine 7
3.2 Connecting the power supply cable 8
3.3 Starting the machine 8
3.4 Switching off the machine 8
4. Working with the ELAN 9
4.1 General application tips 9
4.2 Replacing the sanding disc 10
4.3 Re-equipping the sanding plate support 11
4.4 Emptying the dust bag 12
5. Storage 12
6. Maintenance routines 13
6.1 Tightening the V-belt 13
6.2 Changing the V-belt 14
6.3 Renewing the attachment belt pulley 15
6.4 Renewing the carbon brushes 16
6.5 Checking the dust suction system 17
6.6 Replacing the steering wheels 17
6.7 Replacing the motor belt pulley 18
6.8 Cleaning the machine following
restoration tasks 18
6.9 Adjusting the steering wheels 19
7. Regular checkup according to safety
regulations and VDE 20
8. Troubleshooting 21
9. Safety precautions 22
Circuit diagram 24
Spare parts 26
Service passport 33
EU Declaration of conformity 34
3
INTRODUCTION











I
'






Other manuals for ELAN
1
Table of contents
Other Lagler Sander manuals

Lagler
Lagler Trio User guide

Lagler
Lagler UNICO User manual

Lagler
Lagler Flip User manual

Lagler
Lagler HUMMEL User guide

Lagler
Lagler TRIO 900.65.00.100 User manual

Lagler
Lagler HUMMEL User guide

Lagler
Lagler Flip User manual

Lagler
Lagler Flip User guide

Lagler
Lagler ELAN User manual

Lagler
Lagler HUMMEL User manual
Popular Sander manuals by other brands

Makita
Makita BO6030 instruction manual

Frank
Frank PYTHON C 048666 operating instructions

Bosch
Bosch GBS 75 AE Professional Original instructions

pela tools
pela tools 503230 instruction manual

Silver Eagle
Silver Eagle SE140A quick start guide

Black & Decker
Black & Decker KA900E Powerfile Original instructions