Lakeland Mills CF1126 User manual

CF1126 CEDAR LOG CHAIR
or
CF1148 LOVE SEAT
Please check contents before assembly. If any items are missing or damaged, do not take the unit back
to the store. Call 1-800-427-5136 for customer service and we will save you time by correcting any prob-
lems directly for you.
NOTE:
 Read all instructions before starting.
 The two differences between the chair and the love seat are
the length of the seat and back.
 Do not completely tighten any screws until the unit is fully
assembled and setting on a level surface.
 Use a rubber mallet (or a block of wood between the ham-
mer and the unit) to drive doweled ends into holes as far as
possible.
LOG CHAIR & LOVE SEAT COMPONENTS LOG CHAIR & LOVE SEAT HARDWARE
(Shown smaller than actual size)
NOTE: Cracks or Checks in logs are part of the
natural beauty of cedar logs and should not be
considered defects.
TOOLS REQUIRED
Lay assembled seat on floor. Insert dowel
end of uprights on assembled back into holes
on the back seat rail, ad-
just uprights in or out as
needed to align properly.
Do not tap on seat back
with hammer.
To keep the seat rail from splitting, lay the back on
the floor and drive the seat onto the dowelled ends
by hitting on the bottom of the seat assembly.
STEP 1
7/16” socket or
wrench
Optional
power drill
Fourteen 2 1/2” screws
TIPS
 A battery operated or electric drill will make
assembly faster and easier.
 Use a good quality penetrating oil or wood deck
sealer with a UV inhibitor & an anti-fungal.
(Make sure product is intended for outdoor use.)
 If staining or finishing before assembling, tape
off all dowel ends. (Finishes will cause the dow-
els to swell, making assembly difficult.
Tap uprights in or out until dowel drops into hole.
Uprights

Make a right leg set and a left leg set by
inserting dowel end of back leg into angled hole
of front leg. The drilled holes on each leg should
face the same direction as shown in figure 2.
Put arms onto legs by inserting dowel end of front
legs into the hole in the arms. Drive arm onto leg
assembly as far as possible.
Lay back and seat assembly on its side and
insert dowel ends of seat rail into holes on leg sets.
Drive legs on as far as possible. Turn assembly over
and repeat procedure for the other side.
Set chair in upright position on a level surface and
when legs are in proper position, bring ARM in against
UPRIGHT. Tighten the preinstalled lag screws into the
pilot hole in the arm with a wrench or socket.
Secure doweled joints in place with screws perpendicular to
the doweled ends as shown in figure 4 and figure 6. Repeat
procedure for other side.
Tilt chair back and screw a brace on each side of front
leg to chair bottom as shown in figure 5.
Set unit on a level surface and tighten down all
lag screws firmly to secure unit. Secure all dowel
joints in place with screws perpendicular to the
doweled end as shown in figure 6.
Your chair is now assembled and ready for finish or
immediate use.
Factory: 1 Lakeland Place, Edmore, Michigan 48829, Phone: [phone] Fax: [phone],
www.lakelandmlls.com
Check all joints for tightness before and during each usage season.
If you have hardware left over after completing your unit, it most
likely has been assembled incorrectly, and may not be safe to use.
Please call Customer Service at 800-427-5136 for assistance.
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
https://www.youtube.com/watch?v=VjvdmG34Oqw
Look for assembly videos on:
Upright
NOTE
https://www.youtube.com/watch?v=zLXo9pETXa4
Lakeland Mills recommends:
WeatherSeal Premium Oil-Based Exterior Wood Stain & Sealant
www.ContinentalProd.com