LaMotte TRACER pH PockeTester User manual

Water Testing Leader Since 1919!
Tracer pH PockeTesterTM
Code 1741
Do Not allow pH sensor to dry out.
¬ Store Upright
¬ Before first use, tap meter against
palm to move electrolyte to tip.
See pages 8 and 11.

WARNING! This set contains chemicals
that may be harmful if misued. Read
cautions on individual containers
carefully. Not to be used by children
except under adult supervision.

LaMotte TRACER pH PockeTesterTM 1741 Instruction 3
TRACER
pH POCKETESTERTM CODE 1741
Introduction...................................................................................... 4
Specifications .................................................................................. 4
Parts & Accessories ........................................................................ 5
Contents ........................................................................................... 5
Meter Description
Front Panel Description ......................................................................6
TRACER Display............................................................................... 6
Basic Operation
Powering the TRACER........................................................................7
Automatic Electrode Recognition ......................................................7
Automatic Calibration
Changing the Display Temperature Units ..........................................7
Data Hold ............................................................................................7
Display Messages
CAL Reminder ....................................................................................7
RENEW................................................................................................8
pH Testing
Overview .............................................................................................8
pH Display...........................................................................................8
Getting Started....................................................................................8
Preparation of Buffers.........................................................................9
pH Calibration .....................................................................................9
Meter Reset........................................................................................10
pH Measurement ...............................................................................10
Storing Readings ...............................................................................10
Recalling Stored Readings................................................................10
Maintenance
Storage...............................................................................................11
Battery Replacement .........................................................................11
Cleaning & Conditioning the Electrode ............................................11
Replacing the Electrode ...................................................................12
Troubleshooting.................................................................................13
Expand Your TRACER ..................................................................... 14
Safety............................................................................................... 15
Warranty .......................................................................................... 15

4 LaMotte TRACER pH PockeTesterTM 1741 Instruction
INTRODUCTION
Thank you for selecting the pH TRACER PockeTester. This instrument is
designed for high accuracy pH testing. This device is shipped fully tested and
calibrated and, with proper use, will provide years of reliable service.
SPECIFICATIONS
Display Multifunction LCD with Bar graph
Operating Conditions 32 to 122°F (0 to 50°C) and < 80% RH
pH Range & Accuracy 0.01 to 14.00/±0.01 pH typical
Temperature Compensation Automatic from 32 to 194°F (0 to 90°C)
Temperature Range 23 to 194°F (–5 to 90°C)
Temperature Resolution 0.1° up to 99.9, then 1° thereafter
Temperature Accuracy ±1.8°F/1°C [from 23 to 122°F (–5 to 50°C)]
±5.4°F/3°C [from 122 to 194°F (50 to 90°C)]
Measurement storage 15 tagged (numbered) readings
Power Four CR2032 button batteries (see Page 6)
Low battery indication BAT appears on the LCD
Auto power off After 10 minutes of inactivity
Dimensions 1.4 x 6.8 x 1.6” (35.6 x 172.7 x 40.6 mm),
3.85 oz (110g)

LaMotte TRACER pH PockeTesterTM 1741 Instruction 5
PARTS & ACCESSORIES
pH Replacement Electrode Code 1733
Weighted Stand w/Sample Cups (5) Code 1746
Sample Cups w/caps (24) Code 1745-24
pH 4.01 Mini Buffer Tablets (100) Code 3983A-J
pH 7.01 Mini Buffer Tablets (100) Code 3984A-J
pH 10.0 Mini Buffer Tablets (100) Code 3985A-J
CONTENTS
pH TRACER PockeTester Kit, 0.00-14.00 pH Range Code 1741
Includes:
Sample Cup w/cap *
Tablet Crusher Code 0175
Buffer Tablets, pH 4.0, 7.0, & 10.0 *
*Not sold in this quantity. See Parts & Accessories.

6 LaMotte TRACER pH PockeTesterTM 1741 Instruction
METER DESCRIPTION
Front Panel Description
1. Battery compartment cap
2. LCD display
3. MODE button
4. CAL button
5. ON/OFF button
6. Electrode collar
7. Electrode
(Note: The Electrode cap is not shown)
TRACER DISPLAY
1. Bar graph reading
2. Bar graph scale designations
3. Units of measure
4. Calibration indicators
5.
RENEW and CAL indicators
6. Measurement reading
7.
BAT (low battery) and
HOLD (data hold) indicators
8. Temperature display
3
2
7
1
4
5
6
8
1074
2.0
012
1000
7.0
500
BAT HOLD
mvpHppm
10.04
°C
°F
78.6
RENEW
CAL

LaMotte TRACER pH PockeTesterTM 1741 Instruction 7
BASIC OPERATION
Powering the TRACER
If the batteries are weak, the BAT indicator will appear on the display. Press the
ON/OFF button to turn the TRACER on or off. The auto power off feature will
shut the TRACER off automatically after 10 minutes of inactivity.
Automatic Electrode Recognition
When the TRACER is turned on, it will recognize the type of electrode that is
connected and will display the appropriate unit of measure. An electrode must be
attached before turning the meter on.
Automatic Calibration
When the TRACER is turned on, it will enter theAutomatic Calibration mode.
SELF and CAL will appear while calibration is in progress. After the calibration
is completed, the SELF and CAL display icons will extinguish and both the main
display and the bar graph will read in pH units. The readings will flash on the
display until they have stabilized.
Changing the Displayed Temperature Units
Press and hold the CAL button for approximately 3 seconds. The °C or °F icon
will change first and the numerical temperature value will change only after the
button is released.
NOTE: If the calibration mode is accidentally accessed and CAL appears on the
display, turn the TRACER off and begin again.
Data Hold
Press the MODE button to freeze the current reading. The HOLD display icon will
appear along with the held reading. The held reading will be stored in memory.
Press the MODE button to return to normal operation.
DISPLAY MESSAGES
CAL Reminder
When the TRACER is turned on for the 15th time, without recalibration the
CAL icon will appear on the display indicating the the TRACER may require
calibration. Some applications may require recalibration of the electrode
sooner than others. The CAL display is a reminder and will turn off when the pH
electrode is recalibrated.
RENEW
A flashing “RENEW” warning indicates that the probe may be nearing the end
of its useful life. If cleaning or recalibration does not cause the Renew icon to
disappear, replace the electrode (see optional accessories). The Renew display
appears when the output of the pH electrode fails a diagnostic test.

8 LaMotte TRACER pH PockeTesterTM 1741 Instruction
pH TESTING
Overview
pH is a unit of measure (ranging from 0 to 14 pH) indicating the degree of
acidity or alkalinity of a solution. pH tests are the most commonly performed
measurements in water analysis, using the negative log of the hydrogen ion
activity of a solution which is an indicator of acidity or alkalinity. Solutions with
a pH of less than 7 are considered acidic, solutions with a pH of higher than 7 are
known as bases, and solutions with a pH of exactly 7 are considered neutral.
The pH scale is logarithmic, so, for example, if Sample A is 1 pH less than
Sample B, this means that sample A is 10 times more acidic than Sample B.
A difference of 1 pH represents a ten-fold increase or decrease in acidity.
pH Display
When the electrode is placed in a solution, the main display and bar graph will
indicate the pH reading while the lower display will read temperature. Readings
flash until they have stabilized. The bar graph is ‘center zero’, i.e. at pH 7 there is
no display. As the pH rises, the bar will move from the center to the right. If the
pH drops, the bar will move from the center to the left.
Getting Started
1. Remove the cap from the bottom of the TRACER to expose the electrode
glass surface and reference junction.
2. Before first use or after storage, soak the electrode (with cap removed) in a
pH 4 buffer or tap water for 10 minutes.
3. Before first use, hold the meter by the top battery compartment and swiftly
tap the back of the meter downward into your palm (not a hard surface).
This assures that the internal electrolyte solution moves to the very tip of the
electrode. The electrolyte should fill the circular junction window at the tip
of the electrode.
4. White KCl crystals may be present in the cap. These crystals will dissolve in
the soak or they can be rinsed off with tap water.
5. Always calibrate close to the expected measurement value.
6. A sponge is located in the electrode protective cap. Keep this sponge soaked
with a pH 4 solution to prolong the life of the electrode during storage.

LaMotte TRACER pH PockeTesterTM 1741 Instruction 9
Preparation of Buffers
1. Fill a sample cup with 20 mL of distilled or deionized water.
2. Add one buffer tablet:
pH 4.0 Code 3983A
pH 7.0 Code 3984A
pH 10.0 Code 3985A
3. Use the tablet crusher (0175) to crush the tablet. Stir until the tablet has
disintegrated.
NOTE: Buffers should be prepared fresh daily.
pH Calibration
The TRACER can be calibrated at 1, 2 or 3 points. For the most accurate results
with a two point calibration, calibrate the TRACER with a pH 7 buffer first, then
calibrate with either a pH 4 or pH 10 buffer whichever is closest to the pH value
of the sample to be tested. When performing a three point calibration, calibrate
with the pH 7 buffer first, followed with the pH 4 buffer and then the pH 10
buffer. For the most accurate results, always calibrate at the sample temperature.
1. Place the electrode into a buffer solution (4, 7, or 10 pH) and press the CAL
button. Typically, pH 7 is calibrated first, then 4 or 10, depending on the
measurement range. If readings are going to be made over the entire range,
calibrate with 4, 7 and 10 buffers.
2. The TRACER will automatically recognize the solution and calibrate itself to
that value. The circled number on the display will match the pH of the buffer.
Note that if the buffer is more than 1 pH unit off from the 4, 7, or 10 pH
buffer, the TRACER will assume an error and abort the calibration. CAL and
END will be displayed.
3. During calibration, the pH reading will flash on the main display.
4. When calibration is complete, the TRACER will automatically display END
and return to the pH measurement mode.
5. Rinse the electrode with distilled water.
6. The appropriate circled indicator (4, 7, or 10) will appear on the display
when a calibration has been completed. The calibration will be stored until a
new calibration is performed.
7. For a two- or three-point calibration, repeat Steps 1-5.
8. The meter should be calibrated before each use to obtain the most
accurate results.
9. Always turn the meter off and then on before calibrating to allow sufficient
time to complete the calibrations during one power cycle. If the meter
auto powers off during calibration the calibrations remain valid, but new
calibrations will turn the circled indicators off.

10 LaMotte TRACER pH PockeTesterTM 1741 Instruction
Meter Reset
If the meter will not calibrate or displays a -1, reset the meter and attempt to re-
calibrate.
1. Turn off the meter.
2. Remove the battery cartridge from the top of the meter.
3. Press the ON/OFF button for 10 seconds to bleed off all charges within the
meter.
4. Re-insert the batteries and turn the meter on.
5. Follow the pH Calibration procedure.
pH Measurement
1. Place the electrode in the test sample.
2. Record the pH after the reading becomes stable and the display stops
flashing.
3. Press the ON/OFF button to turn the meter off. Rinse the electrode with
distilled water. Replace cap
pH Measurement of Soil
1. Place a 1:1 ratio of soil and distilled water in a small beaker. For most
analyses, 20 grams of soil and 20 grams distilled water are sufficient.
2. Wait 15 minutes. Stir occasionally with a stirring rod.
3. Stir the sample. Immediately place the electrode in the sample.
4. Wait until the display stabilizes. Record the pH.
5. Rinse the electrode in distilled water. Replace cap.
NOTE: The flat surface electrode will allow for readings directly from the soil if
there is enough moisture present in the soil.
Storing Readings
1. After the reading is made press the
MODE button to store the current
reading The storage location number
will be displayed followed by the
reading being stored.
2. Press the MODE button to return to
normal operation.
3. Repeat step 1 to store the next reading.
4. If an attempt is made to store more than 15 readings, the stored readings
(starting with the first reading) will be overwritten.
HT4 HOLD
pH
10.04
°F
78.6
4

LaMotte TRACER pH PockeTesterTM 1741 Instruction 11
Recalling Stored Readings
NOTE: First ensure that the HOLD symbol is not displayed. If it is, exit the
MODE function by pressing the MODE button.
1. Press the CAL button once and then press the MODE button immediately
after CAL is displayed; the location number (1 through 15) will flash. If the
CAL mode is accidentally accessed (display flashing), press the CAL button
again to exit.
2. The last stored reading taken will be displayed first. To advance through the
stored readings, press the MODE button. The location number is displayed
first, followed by the reading stored in that location.
3. To exit the recall mode, press the CAL button and the TRACER will return to
normal operation. If the batteries are removed, any stored readings and user
calibrations will be discarded.
MAINTENANCE
Care/Storage of Electrode
1. Always rinse the electrode in tap, distilled or deionized water between
measurements to avoid cross-contamination of the samples. Double rinsing is
recommended when high accuracy is required.
2. To preserve electrode life keep the sponge in the protective cap soaked
with a pH 4 buffer. Cap TRACER when not in use. Store vertically.
Do Not allow sensor to dry out.
3. Do not touch the electrodes. Touching the surface of the electrodes may damage
and reduce the life of the electrodes.
4. Salt deposits may build up in the storage cap and should periodically be
rinsed away. These deposits could affect measurements at low conductivity.
Battery Replacement
1. Twist off the battery compartment cap.
2. Hold the battery housing in place with one finger. Remove the battery
carrier by pulling on the small tabs.
3. Replace the four CR2032 batteries. Observe polarity.

12 LaMotte TRACER pH PockeTesterTM 1741 Instruction
4. Replace the battery compartment cap.
NOTE: If the batteries are removed, stored data and user calibrations will
be cleared. A new user calibration will be required. Factory calibrations will
be retained.
All EU users are legally bound by the Battery Ordinance to return all
used batteries to community collection points or wherever batteries/
accumulators are sold.
Disposal in household trash or refuse is prohibited.
DISPOSAL: Follow the valid legal stipulations in respect of the disposal of the
device at the end of its life cycle
Other Battery Safety Reminders
• Never dispose of batteries in a fire. Batteries may explode or leak.
• Never mix battery types. Always install new batteries of the same type.
Cleaning and Conditioning the Electrode
Surface Cleaning – Only in case of visible surface contamination or if readings
should become erratic, use a disposable laboratory towel wetted with ethanol or
isopropyl alcohol and gently rub the surface, until no more residue is visible.
Replacing the Electrode
The TRACER is shipped with an electrode attached. Electrode life is limited
and is dependant on the frequency of use and care. If the electrode needs to be
replaced, follow these steps for removing and connecting electrodes.
1. Turn meter off.
2. To remove the electrode, turn the collar counter-clockwise and remove it.
3. Gently rock the electrode from side to side, pulling it downwards, until it
disconnects from the meter.
4. To attach an electrode, carefully plug the electrode into the meter socket.
Note that the electrode connector is keyed to ensure a proper connection.
CAUTION: Take case to align pins carefully. Bent or broken ins will cause
the meter to malfunction.
5. Tighten the electrode collar firmly enough to make a good seal. A rubber
gasket will seal the electrode with the meter.

LaMotte TRACER pH PockeTesterTM 1741 Instruction 13
TROUBLESHOOTING
Problem Cause Action
Power on
but no display Batteries Insert batteries
Batteries Verify correct polarity
Batteries Replace batteries
Unstable
readings Electrode Immerse electrode more deeply in sample
Electrode Condition electrode before first
use
Electrode Remove air bubbles caught under
electrode
Electrode Clean electrode
Electrode Replace electrode
Slow response
time or reading
drift
Clogged junction Soak in 4.07M Potassium
Chloride (KCl) at 60°C for 30
minutes
Strong alkaline
measurement Soak in 0.1M Hydrochloric acid (HCl) overnight
Deteriorated gel layer Replace electrode
Protein coating on
electrode surface Soak in 1g Pepsin dissolved in 10 mL of 0.1M HCl for 30 minutes
or as needed
Oil, paint, dyes,
suspended solids on
electrode
Rinse electrode alternately with
materials solvent then a buffer
7.00
Dry bulb Dehydrated membrane,
long term storage without
wetting
Soak electrode tip in wetting cap
filled with 1 mL 4.0 buffer for
24-48 hours
Static charge Wiping electrode Rinse electrode in 4.0 buffer and
blot. Do not wipe electrode
Same readings
in different
buffers and
samples
Cracked or broken
electrode Replace electrode. Use bulb guard. Avoid plunging electrode
into bottom of container and stir
bars.

14 LaMotte TRACER pH PockeTesterTM 1741 Instruction
Problem Cause Action
Erratic LCD
display Samples have low ionic strength (lack salt); e.g.
distilled, deionized,
boiled, lake water (high
pressure)
For each 50 mL of sample add
1 drop (50 mL) of saturated
Potassium Chloride (KCl). No
alteration in pH will occur by
inert KCl.
Unexpected
readings Buffers Calibrate with fresh buffers
Buffers Calibrate with buffers that bracket
sample pH
Display frozen HOLD function Press MODE or turn meter off
Button response Remove batteries press ON/OFF
button for 3 seconds. Reinsert
batteries (stored data will be lost)
Steady “-1 ”
display Wait Reading not stable yet
If the meter will not calibrate or displays a -1, reset the meter and attempt to re-
calibrate.
1. Turn off the meter.
2. Remove the battery cartridge from the top of the meter.
3. Press the ON/OFF button for 10 seconds to bleed off all charges within the
meter.
4. Re-insert the batteries and turn the meter on.
5. Follow the pH Calibration procedure.
• If the unit appears to be locked (display frozen) it is possible that the Data
Hold mode has been inadvertently accessed by pressing the MODE button.
Press the MODE button again or turn the meter off and restart if the display
appears frozen.
• If the meter does freeze and no button presses revive it, remove the batteries,
press the ON button for 10 seconds and then reinsert the batteries.
• If the batteries are removed, any stored readings will be discarded and the
user calibration data for pH will be cleared. New user pH calibration data is
required. However, factory calibration data will be retained.
EXPAND YOUR TRACER
Interchangeable electrodes are available to convert the pH TRACER to a Total
Chlorine TRACER or an ORPTRACER.
Remember to ask for instructions and appropriate reagents or buffer tablets when
ordering the Total Chlorine or ORP electrodes.

LaMotte TRACER pH PockeTesterTM 1741 Instruction 15
Total Chlorine TRACER Electrode, 0.0-10.0 ppm Code 1732
The Total Chlorine TRACER Electrode (Code 1732) requires the
use of TRACER TCL Tablets. Order Code 7044-J (100 pack).
ORP TRACER Electrode, ±999 mV Code 1734
The ORP TRACER Electrode (Code 1734) requires an initial
soaking in a pH 4.0 buffer solution. Order pH 4.0 Mini Buffer
Tablets/100 pack (Code 3893-J).
SAFETY
• This device is not a toy. Keep out of the hands of children. It contains
hazardous objects as well as small parts that children could swallow. If a
child swallows any part of this instrument, contact a physician immediately.
• Do not leave batteries and packing material unattended. They can be
dangerous to children if used as toys.
• If the device is going to be unused for an extended period of time, remove
the batteries to prevent draining.
• Expired or damaged batteries can cause cauterization on contact with
the skin. Always use the appropriate gloves and safety precautions when
handling batteries.
• Do not allow the batteries to short-circuit or throw batteries into a fire.
WARRANTY
LaMotte Company warrants this instrument to be free of defects in parts and
workmanship for 1 year from the date of shipment and warrants this probe to be
free of defects in parts and workmanship for 6 months from the date of shipment.
If it should become necessary to return the instrument for service
during or
beyond the warranty period, contact our Technical Service Department
at 1-800-344-3100 or [email protected] for a return authorization number or
visit www.lamotte.com for troubleshooting help. The sender is responsible for
shipping charges, freight, insurance and proper packaging to prevent damage
in
transit. This warranty does not apply to defects resulting from action of the
user such as misuse, improper wiring, operation outside of specification, improper
maintenance or repair, or unauthorized modification. LaMotte Company
specifically disclaims any implied warranties or merchantability or fitness for
a specific purpose and will not be liable for any direct, indirect, incidental or
consequential damages. LaMotte Company’s total liability is limited to repair or
replacement of the product. The warranty set forth above is inclusive and no
other warranty, whether written or oral, is expressed or implied.
To register your meter with the LaMotte Service Department,
go to www.lamotte.com
and choose SUPPORT on the top navigation bar.

LaMOTTE COMPANY
Helping People Solve Analytical Challenges®
PO Box 329 • Chestertown • Maryland • 21620 • USA
800-344-3100 • 410-778-3100 (Outside USA.) • Fax [phone]
Visit us on the web at www.lamotte.com
1741-MN 12/13