LaMotte WaterLink Spin Touch DW User manual

n®QUICK START GUIDE
TESTING
1. Press and hold until the meter turns on.
2. Tap . Select a Water Source type. Tap to confirm.
3. Tap . Select a disk series (found on disk packaging). Tap
to confirm.
NOTE: Disk Series are limited by Water Source Type selection.
4. Remove a disk from the packaging.
5. Use the syringe (1189) to fill the disk with the water sample.
6. Insert the disk. Cover the disk with the Universal Disk Cover
(1719). Close the lid.
7. Tap to start test. Tap to stop the test. If the test is
cancelled discard the disk.
8. The results will be displayed.
9. Choose an option.
¬Tap to add a tag.
¬Tap the highlighted to save the test results to the
test log if Auto Save is not enabled.
¬Tap the hightlighted to send the results to the
enabled Mobile Bluetooth Printer.
¬Tap the highlighted to send the results to a
Bluetooth enabled device.
¬Tap to return to the Test Screen.
10. Press and hold for 2 seconds to turn the meter off.
DOS & DON’TS
BEFORE FIRST USE
¬Fully charge battery using the Spin Touch
USB cable and adapter plug in AC outlet.
¬Ensure your Spin Touch has latest
firmware. A USB connection to a
Windows® PC is required:
1. Download and install WaterLink
Connect 2 Application for Windows at
http://softwarecenter.lamotte.com/.
Select WaterLink Connect 2 Software
for Windows FREE Download.
2. Plug meter into the computer with
the provided USB cable and launch
WaterLink Connect 2 Application from
the Start Menu.
3. A prompt will appear if firmware
updates are available. Select Update.
Testing and data transfer will not
be possible until firmware has been
updated.
NOTE: For water samples over 100 °F (38 °C) subtract
0.3 from pH result or, for the most accurate result,
wait until water sample is below 90 °F (32 °C) to test.
Remove residue daily. Residue will damage the meter
and cause inaccurate results. See Cleaning in manual.
¬Do not touch top or bottom of disk. Handle disk by the
edge.
¬Do not fill disk while in the meter. Fill disk on clean, dry
surface.
¬Fill the disk on a dark surface to more easily see the
sample water.
¬The disk should not contain any large air bubbles. Air
bubbles will result in erroneous results.
¬Always use the disk cover.
¬Only the Universal Disk Cover (Code 1719) can be used
with the WaterLink Spin Touch.
¬Empty syringe of old sample before filling with next
sample.
¬Remove filled disk from meter after testing. Do not
travel with filled disks in meter. They may leak.
¬Keep the chamber clean and dry. Gently swab LED
and photodiode lenses located around the hub with
a cotton swab dampened with streak-free window
cleaner. Do not use alcohol. It will leave a thin film over
the lenses when dry.
¬Go to SETTINGS>Other Settings to select hardness and
nitrogen units. Nitrogen results can be reported in ppm
Nitrate-N units or ppm Nitrate units. 1 Nitrate-N unit =
4.4 Nitrate units.

Disk US Patent No. 8,734,734
FCl US Patent No. 8,987,000
FCl EU Patent No. EP2784503 A1
TCl US Patent No. 8,993,337
[email protected] | 410-778-3100 | 800-344-3100 | www.lamotte.com
FILLING
1. Fill the disk using
slow, even pressure.
The sample water
will fill the spaces
between the baffles in a
counterclockwise order.
Each space will fill from
the bottom to the top.
Sample water should be
added until the sample
water in the fourth
chamber fills to the top
of the chamber slightly
past the embossed
fill line. It is OK to fill
slightly past the fill line.
Correct Fill
(Fill line)
2. Do not overfill the
disk. If the disk is
overfilled, sample
water will flow out
of the overflow hole
in the center of the
disk. The disk is not
leaking. Dry the disk
and run the test.
Overfilled
(Dry disk before placing in meter)
3. Do not under fill the
disk. If the disk is under
filled, the reagent
chambers will not fill
entirely and results will
be inaccurate. Underfilled
4. Do not introduce
air bubbles into the
disk. The reagent
chambers will not fill
entirely and results
will be inaccurate.
As soon as a bubble
starts to form, pull
back on the plunger
to draw the bubble
out of the disk. Begin
the filling process
again.
Air
Bubble
5. Wet disks should be
dried thoroughly with a
lint free wipe. The disk
should be handled by
the edges.
6. Disks should be filled and used within 10
minutes. They cannot be filled ahead of time.
For filling and troubleshooting tips go to: www.lamotte.com/spin_support/
BLUETOOTH CONNECTION
The WaterLink Spin Touch is capable of connecting to a Bluetooth enabled device, such as a phone or tablet.
The Spin Touch is also compatible with a BLE Mobile Printer (5-0067). Other Bluetooth printers are not
supported.
Transferring results over Bluetooth to a mobile device requires that a mobile app is installed on the device
and an active account for the associated software program. For example, with an active WaterLinkSolutions™
account and the WaterLink Solutions mobile app on a phone or tablet, results can be transferred from the
meter into the application. Mobile apps for LaMotte software products are available from iTunes (for iOS
devices) and Google Play (for Android devices).
For detailed information read the Spin Touch manual. Go to http://softwarecenter.lamotte.com/ to learn
more about LaMotte software products.
LaMotte, WaterLink, Spin Touch are ® registered trademarks of LaMotte Company
© 2021 LaMotte Company, All Rights Reserved | 3585-QG | 11.04.21