Landis S755 XL (G2) User manual

S755(G2) / S755 XL (G2)
FINISHER
Operator Manual
Manufactured by

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 2
INTRODUCTION
Landis Finisher S755 (G2) /S755 XL (G2)is a compact, durable machine designed for fast, complete finishing
work. It will deliver efficient, dependable service when used correctly and with care. As with any piece of
specialized equipment, for best performance the manufacturer’s instructions must be followed.
BEFORE USING THE LANDIS FINISHER, READ OPERATING INSTRUCTIONS MANUAL
1. KEEP GUARDS IN PLACE and in working order.
2. Always DISCONNECT ELECTRICAL SOURCE before
adjustments or servicing the machine.
3. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit
of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
4. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use
power tools in damp or wet locations, or expose them
to rain. Keep work area well lighted.
6. KEEP CHILDREN AWAY. All visitors should be kept safe
distance from work area.
7. MAKE WORKSHOP KID PROOF with padlocks, master
switches, or by removing starter keys.
8. DON'T FORCE TOOL. It will do the job better and safer at
the rate for which it was designed.
9. USE RIGHT TOOL. Don't force tool or attachment to do
a job for which it was not designed.
10. DO NOT USE EXTENSION CORD.
11. WEAR PROPER APPAREL. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other jewellery
which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair
covering to contain long hair.
12. ALWAYS USE SAFETY GLASSES. Also use face or dust
mask if cutting operation is dusty. Everyday eyeglasses
only have impact resistant lenses, they are NOT safety
glasses.
13. SECURE WORK. Use clamps or a vise to hold work when
practical. It's safer than using your hand and it frees both
hands to operate tool.
14. Make sure machine is PROPERLY GROUNDED.
15. DON'T OVERREACH. Keep proper footing and balance at
all times.
16. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean
for best and safest performance. Follow instructions for
lubricating and changing accessories.
17. DISCONNECT TOOLS before servicing; when changing
accessories, such as blades, bits, cutters, and the like.
18. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure
switch is in off position before plugging in.
19. USE RECOMMENDED ACCESSORIES. Consult the owner's
manual for recommended accessories. The use of
improper accessories may cause risk of injury to persons.
20. NEVER STAND ON TOOL. Serious injury could occur if the
tool is tipped or if the cutting tool is unintentionally
contacted.
21. CHECK DAMAGED PARTS. Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function -- check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced.
22. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter only.
23. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER
OFF. Don't leave tool until it comes to a complete stop.
24. Dust generated is FLAMMABLE –DO NOT SMOKE when
using Finisher.
25. Keep generators and covers IN PLACE and in proper
working order.
26. Observe all SAFETY WARNINGS on the machine and in this
manual.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 3
OPERATING THE LANDIS FINISHER S755 (G2) / S755 XL (G2)
RISK OF INJURY
•DISCONNECT TOOLS BEFORE SERVICING AND LOCK THE SWITCHES.
•EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN THE
SANDER IS IN USE.
•EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST, WHICH COULD CAUSE EYE
INJURY.
•AVOID KICK BACK BY SANDING IN ACCORDANCE WITH THE DIRECTIONAL ARROWS.
•CLOSE SANDING DOORS BELT BEFORE OPERATING THE MACHINE.
•CLOSE THE MAIN ACCESS DOOR AND FAN COVER BEFORE OPERATING THE MACHINE.
INSTALLATION
The S755 (G2) / S755 XL (G2) Landis Finisher should be located on a flat, firm surface,
in an area free of obstructions that could interfere with the safe operation of the
equipment. The finisher should be mounted on four wheels. In this way, the wheels
are practical to clean and move the machine.
•ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN AND MUST CONFORM TO ALL
STATE AND LOCAL ORDINANCES.
•DO NOT, UNDER ANY CIRCUMSTANCE, TAMPER WITH, MODIFY, OR ADAPT THE ELECTRICAL PLUG AND CORD
PROVIDED WITH THIS MACHINE.
ELECTRICAL CONNECTIONS
Electrical connection may be made by either plugging the provided electrical
cord into an appropriately wired electrical socket, or by wiring the machine
directly into an electrical disconnect box. The customer must ensure that the
voltage is 230 V.
•IF THE ELECTRICAL CORD, PLUG OR WIRING SHOULD BECOME FRAYED OR DAMAGED, REPLACE IT AT ONCE.
DO NOT ATTEMPT TO OPERATE THE MACHINE WITH FAULTY WIRING AS IT COULD RESULT IN SEVERE INJURY
OR DEATH.
NOTE: REFER TO THE MACHINERY IDENTIFICATION PLATE TO DETERMINE THE ELECTRICAL SPECIFICATIONS
OF THIS MACHINE IN RESPECT TO VOLTAGE, PHASE AND AMPERAGE REQUIREMENTS.
•DO NOT START FINISHER BEFORE CHECKING FOR PROPER SANDING BELT TRACKING.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 4
ELECTRICAL CONTROL BOX
The electrical control box is in front of the
machine. The motor is thermally
protected. In case of overload, the relay
will trip and shut the motor off. The
overload on the motor must be reset
after a short period of time (see page 25).
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is
equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. The conductor with insulation having an outer surface that is green
with or without yellow stripes is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor
to alive terminal.
Check with a qualified electrician or service personnel
if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding plugs, A, and 3-pole receptacles that
accept the tool's plug, B.
Repair or replace damaged or worn cord immediately.
Make sure the tool is connected to an outlet having the same configuration as the
plug. No adapter is available or should be used with this tool. If the tool must be
reconnected for use on a different type of electric circuit, the reconnection should
be made by qualified service personnel; and after reconnection, the tool should
comply with all local codes and ordinances.
A
B

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 5
LOCKOUT PROCEDURES
PREPARATION
1. Notify all affected workers that a lockout is required and
the reason for the lockout of the machine.
MACHINE OR EQUIPMENT SHUTDOWN AND ISOLATION
1. If the equipment is operating, shut it down by the normal stopping procedure (turn
off the main switch). We recommend to install a padlock to the Electrical control
panel.
2. Disconnect the electrical plug from the electrical source.
APPLICATION OF LOCKOUT / TAGOUT
1. Lock out and tag the switch with an assigned, individual lock. A worker will not be
protected unless he/she uses his/her own padlock.
2. If more than one worker is working on the same piece of equipment at the same
time, each one should lock out the equipment, by placing a personal lock and tag
on the group lockout device when he/she begins work, and should remove those
devices when he/she stops working on the machine or equipment.
3. Locks and tags should clearly show the name of the person who applied the device,
the date, and the reason for the lockout. This identifies who is servicing the
machinery or equipment. In a multiple lockout/tagout situation, it will also identify
any worker(s) who may not have finished working.
4. Locks and tags must be durable enough to withstand the environment in which they
are to be used. Information on the locks and tags should remain legible.
5. Locks must be substantial enough to prevent removal without the use of excessive
force. Tags must be substantial enough to prevent accidental or inadvertent
removal.
6. Both locks and tags are to be standardized by color, shape, or size. Tags should be
easily recognized and provide appropriate information about the lockout.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 6
RELEASE FROM LOCKOUT / TAGOUT
1. Before locks and tags are removed and electricity is restored to the machine,
inspect the work area to ensure that non-essential items have been removed and
that machine components are operationally intact.
2. Ensure workers are a safe distance from any potential hazard.
3. The lock and tag should be removed from each energy-isolating device by the
worker who applied the lock and tag.
4. Notify affected workers that locks and tags have been removed.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 7
Power Switch
Emergency Button
START-UP
•EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN
SETTING UP THE MACHINE. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND
DUST, WHICH COULD CAUSE EYE INJURY.
Before shipment, your Landis Finisher S755 (G2) / S755 XL (G2) was checked at the
factory for proper adjustment and operation. However, due to the possibility of
jarring or damage during handling and shipping, it is necessary to check that the
machine is in proper working order before use.
•BEFORE INITIAL START UP, TURN SANDING BELTS BY HAND TO ENSURE THAT ALL PARTS ARE FREE. DO NOT
START FINISHER BEFORE CHECKING FOR PROPER SANDING BELT TRACKING.
BEFORE CONNECTION TO AN ELECTRICAL POWER SUPPLY
1. Check that the main switch is off.
2. Rotate the sanding belts to see that all parts are free and not
binding. Continue for one complete rotation of the sanding belt,
checking both belts for tears or other damage. You can tell that
one complete revolution has been made when the joint of the
sanding belt has gone by the front pulley twice.
3. Rotate the trimmer section by moving the sole trimmer guard
and turning the feather edge back guard by hand. Make sure
the guards according to the position of the knife. Manual
adjustment procedure page 11.
Trimmer
Brushes
Sanding
Belt
Blower

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 8
4. Rotate the Naumkeag head by hand to see that the sanding pad is not
damaged and the shaft is not bent.
•AS WITH ANY PIECE OF ELECTRICAL EQUIPMENT, THERE IS AN EVER PRESENT HAZARD OF ELECTRICAL
SHOCK WHEN OPERATING OR TOUCHING THE FINISHER. ENSURE THE MACHINE IS PROPERLY GROUNDED
AT ALL TIMES.
•DO NOT FORCE THE EQUIPMENT. IT WILL DO THE JOB BETTER AND SAFER AT THE RATE FOR WHICH IT WAS
DESIGNED.
BEFORE STARTING THE SANDING BELT MOTOR, CHECK THAT THE SANDING BELT
IS TRACKING PROPERLY, AS FOLLOWS
1. “Jog” the sanding belt motor by quickly hitting the “start”
then “stop” button such that the belt turn slowly, then
stop.
2. Continue jogging the motor and check the belt to see
that it stays roughly centered on its forward pulley.
3. Tracking adjustment handle is located to the left of the sanding
belt:
A. Clockwise rotation of the adjustment moves the
belt to the left
B. Counterclockwise rotation moves the belt to the right.
Adjust accordingly as required so that the belt is
tracking properly while running slowly.
4. Start completely the sanding motor. Fine adjust the tracking
of the belt at full speed.
•AS THE INDIVIDUAL SANDING BELTS WEAR FROM USE, IT WILL BECOME
NECESSARY TO MAKE MINOR TRACKING ADJUSTMENTS TO KEEP THE SANDING
•BELTS CENTERED.
Tracking adjustment
B
A

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 9
INSTRUCTION FOR SANDING BELT
1. While grinding be careful that you avoid any contact to the parallel moving band.
An injury of your hand or a damage of the material can result.
2. After working with the sanding belt it must be switched off immediately.
3. Before starting the sanding belts check in any case:
-Are sanding belts strained?
-Is the dust suction switched one?
-Is the respective suction vent open?
To have a efficient dust suction, keep open the appropriate vent.
For sanding metal, keep the vent close and do not use the dust suction.
Although the filter materials is fire proof impregnated the flying sparks could result in
fire!
SANDING BELT REPLACEMENT
•EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN
THE WORK AREA WHEN CHANGING SANDING BELT. EYE PROTECTION IS
REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST, WHICH COULD
CAUSE EYE INJURY.
Sanding belts are easily changed and are available upon
request in various grits to better suit your needs and.
•Sanding belt 24 grit, SKU: 45924
•Sanding belt 40 grit, SKU: 45940
•Sanding belt 80 grit, SKU: 45980
•Sanding belt 100 grit, SKU: 459100
•Sanding belt 120 grit, SKU: 459120
•Sanding belt 150 grit, SKU: 459150
•SOME SANDING BELTS ARE CONSTRUCTED TO ROTATE IN ONE DIRECTION ONLY. CHECK ARROW INSIDE
SANDING BELT FOR ROTATION. INCORRECT INSTALLATION CAN CAUSE SUDDEN BELT FAILURE RESULTING
IN SERIOUS INJURY TO OPERATOR AND OTHERS IN THE WORK AREA.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 10
TO REPLACE THE 4” WIDE SANDING BELT
1. Open sanding belt door.
2. Release pressure on the sanding belt by pulling
the black arm on top of the machine.
3. Reach in access door and remove the far end
of the belt of the idler first.
4. To install the new sanding belt, reverse the procedure
described above, then readjust the tracking as described
earlier in section “start-up”.
•DO NOT START FINISHER BEFORE CHECKING FOR PROPER SANDING BELT
TRACKING.
•DO NOT OPERATE MACHINE WITH ACCESS DOOR OPEN.
•NEVER LEAVE MACHINE RUNNING WHILE UNATTENDED. TURN IT OFF.
•AS INDIVIDUAL SANDING BELTS WEAR FROM USE, IT WILL BECOME NECESSARY TO MAKE MINOR TRACKING
ADJUSTMENTS TO KEEP SANDING BELTS CENTERED.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 11
TRIMMER SECTION
TO REMOVE THE SOLE CUTTER
1. You will need to use the lock tool at first to secure
and lock the shaft. (SKU: TBSHC)
2. Remove the cutter retaining screw
(left hand thread), (SKU: 83102220) and the washer
(SKU: F33116).
3. Pull cutter off the shaft.
4. To reassemble, reverse procedures.
TO REMOVE THE HEEL CUTTER
1. You will need to use the lock tool at first to secure and lock the
shaft. (SKU: TBSHC)
2. Unscrew the black knob at the back of the guard and remove
it by sliding to the left.
3. Remove the cutter retaining screw (left hand thread),
(SKU: 83102220) and the washer (SKU: SCT).
Wear protective gloves to manipulate the cutter. Retain the
retaining rod (SKU: TBSHC) and make a rotation towards the
bottom to remove the cutter on bayonet.
4. To reassemble, reverse procedures.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 12
TO CHANGE THE MINI BELT (IN OPTION)
1. You will need to use the lock tool at first to secure
and lock the shaft. (SKU: TBSHC)
2. Remove the screw (SKU: 83102220) (left hand thread)
and the washer (SKU: SCT).
3. Pull the rubber wheel out of the shaft.
4. Change the sandpaper belt.
5. Reverse procedures to reassemble.
TO ADJUST THE TRIMMER SHIELD (GSL)
1. Use an Allen key, provided, to release the shield (1/8’’).
2. The trimmer shield shouldn’t touch cutter,
turn set screw clockwise to move Shield
outward. Make adjustment to keep a small
gap between the shield and the cutter.
3. Adjust the trimmer shield up or down as
necessary. Turn knob counter clockwise
to raise shield vertically.
✓Maintenance is important, see our recommendations page 19-21.
Mini belt
TMS001002MA

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 13
BRUSH UNIT
1. Open the dust damper below the polishing wheels.
2. Switch on the device by pressing the green button for the
sander.
3. Never grap into the running device! Switch off the device
immidiately after using it!
4. Change the polishing brushes in the following direction:
-Switch off the machine by pressing the main switch off
-Loosen the retaining screws on
the polishing
fittings flange using allen key.
-Installed the new brush on the
bayonet tighten the fittings.
-Check the set-screws before
operating with the unit for a tight
fit.
Only for S755 XL (G2): contains tow brushes at left are fixed and two brushes at right
are on bayonet.
NAUMKEAG
It is possible to adjust the blasting angle using the handles
on the right of the motor. Open the naumkeag vent
before using this tool.
Set screw (2)

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 14
OPEN DUST VENT
Pull down the handle at the right of the machine to open the
dust vent. Do the reverse procedure to close it.
SAND PAPER REPLACEMENT
The sand paper can be obtained in various grit to suit your needs
and are easily changed.
•Sandpaper 80 grit, SKU: PN80
•Sandpaper 100 grit, SKU: P100
•Sandpaper 120 grit, SKU: PN120
TO REPLACE THE SAND PAPER
1. Unscrew the nut.
2. Move up the washer and change de sand paper.
3. If necessary, it is possible to change the pad (PN)
according to its wear. Repeat the procedure for
changing paper.
CLOSE
OPEN

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 15
DUST BAG AND DUST DRAWER
Dust composed of leather, rubber and plastic is combustible
and can readily be set on fire by a lighted cigarette or sparks.
This can occur whether the dust is in the dust bag or the
machine duck work leading to the dust bag. Do not sand or
grind metal with the finisher.
The cleaner you keep the dust bag, the less likely you are to
burn a hole in it. Failure to shake the dust bag and empty the
dust drawer daily will not only increase this likelihood, but will
also cause a significant loss of dust extraction from the
sanding, trimming and brushing areas.
✓Maintenance is important, see our recommendations page 17 & 22.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 16
ACCESSORIES
•EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN
THE WORK AREA WHEN USING THE ACCESSORIES SUPPLIED WITH THE LANDIS
FINISHER. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS
AND DUST, WHICH COULD CAUSE EYE INJURY.
ALL ACCESSORIES ARE MOUNTED ON BAYONET FITTING
One end of the sanding shaft is machined to accommodate bayonet fitting
(quick change). Extra tools and sanding wheels are available on request.
When removing the quick change fittings, use the special black spanner wrench
(CCL) supplied with the machine. To remove, engage the spanner in the hole
near the end of the bayonet fitting and apply a sharp rap downward. Before
putting on a fitting be sure the opening ends are cleaned. Hand tightening is
sufficient to hold the fitting in proper position.
N.B. When properly mounted, the bayonet fitting will tighten itself by rotating it in the socket in the
opposite direction of the sanding belt rotation.
•FAILURE TO PROPERLY MOUNT THE ADAPTOR WILL RESULT IN FLYING APART AND POSSIBLE INJURY TO THE
OPERATOR AND OTHERS IN THE WORK AREA.
•THESE QUICK CHANGE ACCESSORIES SHOULD BE PROPERLY ENGAGED ON THE SHAFT TO ENSURE SAFE
OPERATION. MAKE SURE PIN ON SHAFT ENGAGES THE ADAPTOR CORRECTLY.
•THE ACCESSORY MUST BE POSITIONED IN THE MAIN SHAFT SO THAT IT TIGHTENS ITSELF AS IT IS BEING USED.
HEEL BREASTER ON BAYONET
A Heel breaster mounted on a quick change adaptor is
provided with your Finisher and can be used only on the left side
of the main shaft.
/
The breaster has a left handed screw assembly, designed to
tighten during rotation only on the left side of the machine.
Be careful to install the half-moon sandpaper in the groove of the aluminium
breaster. Failure to properly install it will cause vibration when sanding.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 17
MAINTENANCE
A properly maintained machine will give you years of satisfactory service, where
as an abused machine will not. We strongly recommend that you observe the
following procedures for your own benefit and safety.
EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN
SERVICING THE MACHINE. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST,
WHICH COULD CAUSE EYE INJURY.
DAILY AND WEEKLY MAINTENANCE
Clean your S755 (G2) / S755 XL (G2) Finisher daily.
DUST BAG
Shake dust bag regularly with the
handle on the top of the machine.
DUST DRAWER
1. Open the front door if the finisher and turn the
2 handles to open dust drawer.
2. Empty dust drawer daily.
3. The magnets will keep close the front door.
Magnet

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 18
4. Verify if the drawer is perfect adjusted to the seal. It’s possible
to adjusted the level of the drawer. Screw or unscrew the set
screw with an Allen Key. Make sure the block bellow is aligned
to the ledge.
5. Check seal sound drawer and replace if damaged or if it is not
sealed properly.
6. Check seal between the top of the drawer and the dust bag.
7. When the dust drawer is full, dust may spill when the drawer is
removed. Vacuum out the bottom of the machine before
sliding back the drawer.
N.B. The cleaner you keep the dust bag, the less likely you are to burn a
hole in them. Failure to shake the dust bag and empty the dust drawer daily
will only increase this likelihood, but also cause a significant loss of dust
extraction from the sanding, trimming and brushing areas.
RUBBER AND FELT WHEEL
Clean the rubber/felt surface to avoid accumulation of dust. If
there is too much accumulation, the sanding belt won’t stay on
the rubber/felt wheel and you will have problems with tracking.
IDLER WHEEL
Clean the flat surface to avoid accumulation of dust with a
scraper.

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 19
FILTERS
Change them (3 units) when necessary (SKU: G8PM300399).
Put the green side towards the outside of the machine.
TRIMMER CUTTER
1. Check trimmer cutter condition daily.
2. Check for wear on hardened steel cutters and sharpen if
necessary.
For carbide cutter, return to Landis for sharpen.
3. Check for broken teeth on the carbide cutter, if supplied with
your machine, replace cutter.
4. Clean with the air jet the trimmer section.
V-BELT
1. Check the belt with a complete turn by turning the sole trimmer.
2. Check its condition. If it is cracked, replace it.
•MOTOR REPLACEMENT REQUIRES WORKING WITH 220 VOLTS ELECTRICAL WIRING AND CAN BE
HAZARDOUS. PLEASE CALL A QUALIFIED ELECTRICIAN OR A LANDIS TECHNICIAN.
MOTOR
Clean each side of the motor and the wheels with a vacuum cleaner or an air
jet.
If you believe that the motor present an anomaly, please contact our customer
service at 1 800 634-0806.
Worn carbide cutter

Operator Manual S755 (G2) / S755 XL (G2) October 2017
Landis International - 20
•BE ABSOLUTELY CERTAIN TO RECONNECT THE ELECTRICAL WIRE TO THE PROPER TERMINALS.
•FAILURE TO DO SO CAN RESULT IN IMPROPER MOTOR ROTATION, A RUINED MOTOR, FIRE, OR INJURY TO
YOURSELF.
•DUST FROM FINISHER IS COMBUSTIBLE. DO NOT SMOKE WHILE CLEANING THE MACHINE AND DUST
COLLECTOR.
•DAMAGED DUST BAG OR DUST DRAWER SEALS WILL ALLOW THE ESCAPE OF COMBUSTIBLE MATERIALS
CAUSING A FIRE HAZARD AROUND THE MACHINE.
•CHECK DAMAGED PARTS. BEFORE FURTHER USE OF A TOOL, GUARD OR OTHER PART THAT IS DAMAGED,
CHECK CAREFULLY TO DETERMINE THAT IT WILL OPERATE PROPERLY AND PERFORM ITS INTENDED
FUNCTION. CHECK FOR MOUNTING OR ANY OTHER CONDITION THAT MAY AFFECT ITS OPERATION. A
TOOL, GUARD OR OTHER PART THAT IS HARMFULLY DAMAGED SHOULD BE PROPERLY REPAIRED OR
REPLACED.
•IF THE ELECTRICAL CORD, PLUG OR WIRING SHOULD BECOME FRAYED OR DAMAGED, REPLACE IT AT
ONCE.
•REPLACE ALL DOORS AND GUARDS BEFORE OPERATING THE MACHINE.
•DO NOT OPERATE MACHINE WITH SANDER HOUSING DOORS OPEN.
•AFTER MAKING ADJUSTMENTS, REMOVE ALL WRENCHES AND OTHER TOOLS BEFORE OPERATING THE
SANDER.
•USE EXTRA CAUTION WHEN STARTING THE FINISHER FOR THE FIRST TIME AFTER INSTALLING A NEW TOOL OR
PART.