Landscape Forms Carousel User manual

Instructions Assembly Installation Operation
Page 1 of 2
10/2014
Carousel Table with Four Seats
Table Components:
(2) table/seat supports
(1) table top
(4) seats
Note: Marneaux tabletop ships with a circular adapter plate installed, do not remove.
Hardware:
(18) 1/4" x 3/4" Phillips tapping screws for Steelhead and Catena table top OR
(4) 1/4-20 x 3/4” Phillips machine screws with washers for Marneaux table tops
(6) 3/8-16 x 1” hex head machine screws with washers for seats
(1) 1/4-20 x 2-1/4 Phillips machine screw and lock nut for umbrella (sold separately)
(Glides for freestanding support and anchor tabs for surface mount support are factory installed.)
Tools Required:
#3 Phillips screwdriver for Steelhead, Catena, and Marneaux table tops
9/16" socket and ratchet for seat screws
HANDLE WITH CARE! Pangard IIpolyester powder coat is a strong, long-lasting finish. Protect this finish from damage during
assembly. Place unwrapped powder coated parts on packaging foam or other non-abrasive surface. Do not place or slide
powder coated parts on concrete or other hard or abrasive surfaces – this will damage the finish causing corrosion to occur. Use
touch-up paint to repair any finish abrasions.
Assembly:
1. Lay table top upside down on a non-marring surface.
2. Place support A (has 5" ring at center) upside down on table top. Insert screws loosely (6 for Steelhead and Catena or 2 at
ends of plates for Marneaux).
SUPPORT "A”
3. Hold support B upside down and carefully lower it over support A. Place bar of support B into notch in ring on support A.
Insert screws loosely as before.
SUPPORT "B"
Carousel Table with Four Seats continued
4. Tighten all table top fasteners until snug, then tighten additional 1/4 turn. [The use of power drivers is not
recommended with Marneaux tabletops. Threaded inserts may be damaged or broken due to over-torquing.]
5. Turn table right side up, using at least 2 people.

Instructions Assembly Installation Operation
Page 2 of 2
6. Slip stems on seat bottoms into tubes on support. Assemble backless seats with threaded end of hole or flat side of stem
toward center of table. Carefully align threaded hole in stem with hole in tube. This may require lifting the seat slightly.
Insert 3/8-16 x 1” long hex head machine screw with washer through the support hole and tighten. Screws are coated
with dry thread locking compound that cures in 24 hours. Wiggle seats and tighten as necessary until seat is securely
fastened.
WARNING: Seats were NOT designed to swivel. If seating is properly installed and screws are tightened, the seats will
not move. Allowing the seating to swivel will damage the finish and the product.
7. To install umbrella, slide umbrella pole through hole in table and into socket tube on support. Insert 1/4-20 x 2-1/4 screw
through holes in socket and umbrella pole and secure with lock nut.
Recommended procedure for surface mounting to hard-surfacing:
1. Place unit in desired position. Mark hole locations through anchor brackets.
2. Move unit to allow access for drilling holes.
3. Drill holes at marked locations for appropriate anchors. Note: Anchors must be no larger than 3/8" diameter. Corrosion
resistant anchoring hardware is recommended.
4. Although the installer is responsible for anchoring procedure and hardware, we suggest the following:
Poured concrete: 3/8" diameter, stud or sleeve type expansion anchor, minimum 2-1/2" long.
Pavers: If pavers are installed over poured concrete, use 3/8" diameter, stud type expansion anchor with enough length
to go through brick and into concrete.
Wood deck (at least 2" nominal thickness): 3/8" diameter hex head lag bolt, at least 2" long.
5. If using expansion anchors, install anchor leaving approximately 3/4" thread protruding from surface. Place unit in position,
install hex nut with washer and tighten carefully to avoid marring finish.
6. If using lag screws, place unit in position, install lag with washer and tighten carefully to avoid marring finish.