Landscape Forms Carousel User manual

ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.To
protectthisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamor
othernon‐marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardor
texturedsurface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonany
gougesinthefinishcausedbyassemblytools.
Toolsrequired:
•protectivepadding
•3/16hexkey
•Anchoringhardwarenotincludedforsurfacemountunits.PowersFastenersPower‐
Bolt®stainlesssteel3/8”x2‐1/4”hexheadsleeveanchorsarerecommended.(4
required)
•Hammerdrillwith3/8”diametercarbidetippeddrillbit
•Hammer
•Wrench
•9/16”wrench(forseats)
•5/32”hexkey
•7/16”wrench(forumbrellahardware)
WARNING!TABLESMUSTBEFASTENEDSECURELYTOHARDSURFACINGTO
PREVENTTIPPING.
Installation Guide
Carousel standing height table
www.landscapeforms.com Ph: 800.521.2546
Date: June 21, 2018
Page 1 of 3
Standinght SUPPORT‘A’ Standinght SUPPORT‘B’
Footrest
Includedcomponents:
•Support‘A’withsurfacemounttabs
•Support‘B’withsurfacemounttabs
•Footrest
•Seats(qty andstyledependsonorder)
•1tabletopperunit,withattachinghardware
•(1)¼‐20x2‐1/4”Phillipspanheadmachine
screwandlocknut
2X–1/4‐20x7/8”
Hexheadcapscrews
2X–1/4washer
30”dia tabletop,
MarneauxorCatena
27”squarewood
Tabletop
30”dia wood
Tabletop
30”squareMarneaux
Tabletop
Backless
Gridseat
Backless
perfseat
Backed
gridseat
Backed
perfseat
Hoop
seat
4X‐ 3/8‐16x1‐
1/2”indentedhex
headmachine
screw
4X‐ 3/8washer
PROCEDUREFORASSEMBLINGSUPPORTS:SeeFig1andFig2
Note:DONOTDRAGunitacrossconcreteorotherroughsurfaces.Thiscould
damagethepowdercoat onthebottomofthesurfacemounttabs.
1. Verifythatsurfacemounttabsaresecurelyfastenedtosupportlegs.Tightenif
necessary.
2. Slidesupport‘A’oversupport‘B’.Alignnotchinsupport‘A’overbarinsupport
‘B’.SeeFig.1.
3. Slidefootrestoverassembledsupportlegs,aligningtheholesinthefootrest
withtheholesinthesupportbar.
4. Securefootresttosupportlegswith(2)hexheadcapscrewsandwashers.See
Fig.2.

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 3
Fig.1– Assemblesupportlegs
BARONSUPPORT‘B’
NOTCHONSUPPORT
‘A’FITSOVERBAR
SUPPORT
‘A’
SUPPORT
‘B’
Carousel standing height table Date: June 21, 2018
TABLETOPASSEMBLY:SeeFig3.
Note:DONOTDRAGunitacrossconcreteorotherroughsurfaces.Thiscoulddamage
thepowdercoat.
1. Placetabletopupsidedownonnon‐marringlevelsurface.
2. Placeassembledsupportontabletop.Alignholesinbracketsonsupportwithholes
intabletop.
3. Looselyfastensupporttotabletopwithscrewsprovided.
‐Catena/Steelheadtablesinclude(12)1/4‐20x3/4”Phillipstrussheadtapping
screws
‐Marneaux®includes(4)1/4‐20x3/4”Phillipspanheadmachinescrewsand
washers.Onescrewrequiredattheouterholeineachplate.
‐Squarewoodtabletopincludes(12)1/4‐20x1”Phillipspanheadmachine
screws.
Theuseofpowerdriversisnotrecommended.Threadsorthreadedinsertsmaybe
damagedorbrokenduetoover‐torqueing.
4. Installhardware.Tightenalltabletopfastenersuntilsnug,thentightenadditional
1/4turn.
5. Turntablerightsideupusingatleasttwopeople.
PROCEDUREFORASSEMBLINGSEATS:SeeFig4.
Note:TheseinstructionsapplytoallseatstylesforCarouselunits.SeatswereNOT
designedtoswivel.Allowingtheseattoswivelwilldamagethefinishandtheproduct.
1. Slideseatstemintotubeonsupport.Backlessseatsshouldbeinstalledwiththeflat
partofthestemfacingintowardthecenterofthetable.
2. Alignthreadedholeinseatstemwithholeinsupporttube.Thismayrequirelifting
theseatslightly.
3. Insertwasherandhexheadmachinescrewthroughthesupportholeandtighten.
Screwsarecoatedwithadrythreadlockingcompoundthatcuresin24hours.
Wiggleseatsandtightenasnecessaryuntilseatissecurelyfastened,
SURFACEMOUNTINSTALLATION:
1. Placeunitindesiredpositionandmarkanchorlocationsthroughholes
providedinsurfacemounttabs.
2. Moveunitanddrillholes.
3. Cleartheholesofdustanddebrisusingcompressedair.
4. Placeunitindesiredpositionandinstallalloftheanchors.Afterallanchors
areinstalled,tightenasrecommendedbyanchormanufacturer.
5. Periodicallycheckfastenersandtightenifrequired.
UMBRELLAASSEMBLY:
1. Toinstallumbrella,slideumbrellapolethroughholeintableandintotubeon
support“B”.
2. Alignholesinbasetubeandumbrellapole.Insertlong1/4‐20machinescrew
andsecurewithlocknut.
CAUTION:Donotletgooftheumbrellauntilthepolehasbeensecured.
WARNING!Allstandingheightunitsmustbeanchored.

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 3 of 3
Fig.2– Attachfootrest
HOLESON
FOOTRESTALIGN
WITHHOLESON
SUPPORTBAR
HOLESFOR
SECURING
FOOTRESTTO
SUPPORTS
FOOTREST
HEXHEAD
CAPSCREW
WASHER
Carousel standing height table Date: June 21, 2018
Fig.4–Installseat
FLATSIDE
OFSEAT
STEMFACESIN
BACKLESS
GRIDSEAT
SHOWN
MACHINE
SCREW
WASHER
Fig.3–Installtabletop
SCREW
ASSEMBLED
SUPPORT
TABLETOP
(SQWOOD
SHOWN)
ATTACHATTHIS
LOCATIONFOR
MARNEAUX
TABLETOPS