Landscape Forms Strata Beam Bench User manual

Benchoptions
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoatisastrong,long‐lastingfinish.Toprotect
thisfinishduringassembly,placeunwrappedpowdercoatedpartsonpackagingfoamorothernon‐
marringsurface.Donotplaceorslidepowdercoatedpartsonconcreteorotherhardortextured
surface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthe
finishcausedbyassemblytools.
PROCEDUREFORINSTALLATION:
1. Prepareproperconcreteslabasrequired.
2. Freestandingbenchshipswithglidesinstalled.Benchcanbesetinplace.
Important!
•DoNOTdragbenchacrossconcreteorotherroughsurfaces.
•DoNOTliftthebenchbythearms
•DoNOTliftthebackedbenchbythebackpanel.
•DoNOTdropthebench–lowergentlyintoplace.
ForSURFACEMOUNTbench:
1. Tipbenchontoprotectivematerial.Leaveglidesinstalled.
2. Installsurfacemounttaboneachsupport,asshowninFig.1.
3. Setbenchinplaceandmarkholelocations.
4. Movebenchanddrillholesaccordingtodiameteranddepthrequiredbysurface
mountanchormanufacturer.Clearholesofdebris.
5. Setbenchbackinpositionandinstallsurfacemountanchorspermanufacturer’s
instructions.
ForEMBEDDEDbench:
1. Tipbenchontoprotectivematerial.Removeglides.
2. InstallthreadedrodsintosupportsasshowninFig.2.
3. Supportbenchandsetintoposition.
4. Tracearoundthreadedrodstomarkholelocations.
5. Movebenchanddrillholesperanchoringepoxymanufacturer’srecommendations.
Clearholesofdebris.
6. Testfitbenchintoposition,ensuringthatthethreadedrodsarenotrestingonthe
bottomofthedrilledholes.
7. Removebenchandfillholeswithepoxy.
8. Setbenchinposition.Wipeawayexcessepoxybeforeitbeginstocure.
Toadjustlevelingglides:
1. Thestainlesssteelglideshaveflatsidestoallowa1‐1/4”thinwrenchtoadjust.
Includedcomponents:
•Benchshipsfullyassembled
•Forsurfacemount:(2)eachsurfacemt tabs,3/8‐16x5/8”Flatheadcapscrews
•Forembedded:(4)3/8‐16threadedrods
ToolsRequiredforSurfacemountorEmbeddedoption:
•Safetyglasses
•Hammerdrillwithmasonrybits
•(2)non‐corrosiveanchors,max3/8”diameter(surfacemountoption)
•7/32”hexkey(surfacemountoption)
•1‐1/4”thinwrenchforadjustingorremovingfreestandingglides
•Chemicalanchoringadhesive(HiltiHITRE500orequivalent)(embeddedoption)
•Properliftingequipmentwithprotectivepadding(benchesweighbetween280lbs‐
345lbs)
Installation Guide
STRATA Beam Bench
www.landscapeforms.com Ph: 800.521.2546
Date: March 27, 2018
Page 1 of 2
2x–surface
Mounttabs
2x–FHCS
(surfacemt only)
4x– threadedrod
(embeddedonly)
Straight,backless
Straight,backed

Installation Guide
STRATA Beam Bench
www.landscapeforms.com Ph: 800.521.2546
Date: March 27, 2018
Page 2 of 2
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoatisastrong,long‐lastingfinish.Toprotect
thisfinishduringassembly,placeunwrappedpowdercoatedpartsonpackagingfoamorothernon‐
marringsurface.Donotplaceorslidepowdercoatedpartsonconcreteorotherhardortextured
surface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthe
finishcausedbyassemblytools.
Fig.3– Embeddedanchoringdetail
MELDSTONE
SUPPORT
[472mm]
(1819/32”)
REFERENCE
ONLY
Fig.1– Attachsurfacemounttabs
LEAVE GLIDES
INSTALLED
3/8‐16FLATHEAD
CAPSCREW
SURFACE
MOUNTTAB
Fig.2–Installthreadedrodsforembedment
3/8‐16THREADED
RODS
HOLEFORSURFMT
TAB–DONOTUSE
Fig.4–benchproperlifting,backed(shown)orbackless
STRAPS