Landscape Forms Carousel User manual

ASSEMBLE WITH CARE! Pangard IIPolyester Powdercoat is a strong, long-lasting finish. To
protect this finish during assembly, place unwrapped powdercoated parts on packaging foam or
other non-marring surface. Do not place or slide powdercoated parts on concrete or other hard
or textured surface –this will damage the finish causing rust to occur. Use touch-up paint on any
gouges in the finish caused by assembly tools.
WARNING! ALL 3-SEAT TABLES AND ALL TABLES USED WITH METAL
UMBRELLAS MUST BE FASTENED SECURELY TO HARD SURFACING TO
PREVENT TIPPING.
Installation Guide
Carousel dining height table
www.landscapeforms.com Ph: 800.521.2546
Date: January 31, 2020
Page 1 of 4
dining ht SUPPORT ‘A’
1X – 3 seat
Backless
Grid seat
Backless
perf seat
Backed
grid seat
Backed
perf seat
Hoop
seat
Included components:
•Support ‘A’ and ‘B’ for 3 or 4 seat units
•Support ‘A’, ‘B’ and ‘C’ for 5 or 6 seat units
•Seats (qty and style depends on order)
•1 tabletop per unit, with attaching hardware
•(1) ¼-20 x 2-1/4” Phillips pan head machine
screw and lock nut
1X per seat - 3/8-
16 x 1-1/2”
indented hex
head machine
screw
1X per seat –
3/8 washer
dining ht SUPPORT ‘B’
1X – 3 seat
1X – 4 seat
1X – 6 seat
dining ht SUPPORT ‘C’
1X – 5 seat
1X – 6 seat
dining ht SUPPORT ‘B’
1X – 5 seat
dining ht SUPPORT ‘A’
1X – 4 seat
NOTCH
AT 90°
dining ht SUPPORT ‘A’
1X – 5 seat
1X – 6 seat
NOTCHES
AT 60°
39” square wood
Tabletop
42” dia tabletop
Steelhead solid
42” dia tabletop,
Marneaux or Catena
42” dia wood
Tabletop
42” dia tabletop
Steelhead perf
Adapter
Plate -3 seat
unit only
Tools required:
•protective padding
•Phillips head screwdriver
•Non-corrosive anchors, maximum Ø3/8” [9mm] –3 for 3-seat unit, 4 for 4-seat unit,
6 for 5 or 6 seat units
•9/16” wrench (for seats)
•5/32” hex key
•7/16” wrench (for umbrella hardware)
PROCEDURE FOR ASSEMBLING SEATS: See Fig 11. This should be done after
assembling supports to tabletop.
Note: These instructions apply to all seat styles for Carousel units. Seats were NOT
designed to swivel. Allowing the seat to swivel will damage the finish and the
product.
1. Slide seat stem into tube on support. Backless seats should be installed with
the flat part of the stem facing in toward the center of the table.
2. Align threaded hole in seat stem with hole in support tube. This may require
lifting the seat slightly.
3. Insert washer and hex head machine screw through the support hole and
tighten. Screws are coated with a dry thread locking compound that cures in 24
hours. Wiggle seats and tighten as necessary until seat is securely fastened.

ASSEMBLE WITH CARE! Pangard IIPolyester Powdercoat is a strong, long-lasting finish. To protect
this finish during assembly, place unwrapped powdercoated parts on packaging foam or other non-
marring surface. Do not place or slide powdercoated parts on concrete or other hard or textured
surface –this will damage the finish causing rust to occur. Use touch-up paint on any gouges in the
finish caused by assembly tools.
Installation Guide
Carousel dining height table
www.landscapeforms.com Ph: 800.521.2546
Page 2 of 4
TABLETOP ASSEMBLY:
Note: DO NOT DRAG unit across concrete or other rough surfaces. This could damage the
powdercoat on the bottom of the surface mount tabs.
1. Verify that surface mount tabs (if ordered) are securely fastened to support legs.
Tighten if necessary.
2. Place table top upside down on non-marring level surface.
3. For 3 seat units with any table style except Marneaux, place the square adapter plate
on top of cross bars of tabletop. Tabletops for 5 or 6 seat units will ship with the
adapter plate installed. Do not remove the adapter plate.
4. Place table support “A” (has 5” ring at center) upside down on table top and align
holes, see Fig 1, 3, 5 or 8.
5. Loosely fasten support to table top with screws provided.
-Catena/Steelhead tables include 1/4-20 x 3/4” Phillips truss head tapping screws
-Marneaux® includes (4) 1/4-20 x 3/4” Phillips pan head machine screws and washers.
One screw required at the outer hole in each plate.
-Square wood tabletop includes 1/4-20 x 1” Phillips pan head machine screws.
6. Hold table support “B” upside down and carefully lower it over support “A” so bar on
“B” fits into notch on “A”. Loosely fasten support “B” to table top, see Fig 2, 4 6 or 9
7. For 5 or 6 seat units, lower support “C” over installed supports. Loosely fasten to
tabletop. See Fig 7 or Fig. 10.
The use of power drivers is not recommended. Threads or threaded inserts may be
damaged or broken due to over-torqueing.
3. Install hardware. Tighten all table top fasteners until snug, then tighten additional
1/4 turn.
4. Turn table right side up using at least two people.
Fig. 2 –3 Seat table to support install (Marneaux tabletop)
SCREW
MARNEAUX
TABLETOP
SUPPORT
‘A’
ROUND ADAPTER
PLATE – FACTORY
INSTALLED
SUPPORT ‘B’
WASHER
Fig. 1 –3 Seat table to support install (not Marneaux)
SCREW
TABLETOP
(NOT
MARNEAUX)
SUPPORT
‘A’
SQUARE
ADAPTER
PLATE
SUPPORT ‘B’
Date: January 31, 2020

Installation Guide
Carousel dining height table
www.landscapeforms.com Ph: 800.521.2546
Page 3 of 4
Fig. 3 –4 Seat table to support install (not Marneaux)
SCREW
TABLETOP
(NOT
MARNEAUX)
SUPPORT
‘A’
SUPPORT ‘B’
Fig. 4 –4 Seat table to support install (Marneaux tabletop)
SCREW
MARNEAUX
TABLETOP
SUPPORT
‘A’
NO METAL
ADAPTER
PLATE
SUPPORT ‘B’
WASHER
Fig. 6 –5 Seat support ‘B’ install (not Marneaux)
SCREW
SUPPORT ‘A’
SUPPORT ‘B’
Fig. 7 –5 support ‘C’ install (not Marneaux)
SCREW
SUPPORT ‘C’
Fig. 5 –5 Seat support ‘A’ install (not Marneaux)
SCREW
TABLETOP
(NOT
MARNEAUX)
SUPPORT ‘A’
NOTCHES AT 60°
FACTORY
INSTALLED
ADAPTER
PLATE
Date: January 31, 2020

Installation Guide
Carousel dining height table
www.landscapeforms.com Ph: 800.521.2546
Page 4 of 4
Fig. 9 –6 Seat support ‘B’ install (Marneaux)
SCREW
SUPPORT ‘B’
WASHER
Fig. 8 –6 Seat support ‘A’ install (Marneaux)
SCREW
TABLETOP
(MARNEAUX
SHOWN)
SUPPORT ‘A’
NOTCHES AT 60°
WASHER
Fig. 10 –6 support ‘C’ install (Marneaux)
SCREW
SUPPORT ‘C’
WASHER
Fig. 11 –Install seat
FLAT SIDE
OF SEAT
STEM FACES IN
BACKLESS
GRID SEAT
SHOWN
MACHINE
SCREW
WASHER
SURFACE MOUNT INSTALLATION:
1. Place unit in desired position and mark anchor locations through holes provided in surface
mount tabs.
2. Move unit and drill holes.
3. Clear the holes of dust and debris using compressed air.
4. Place unit in desired position and install all of the anchors. After all anchors are installed,
tighten as recommended by anchor manufacturer.
5. Periodically check fasteners and tighten if required.
UMBRELLA ASSEMBLY:
1. To install umbrella, slide umbrella pole through hole in table and into tube on support
“B”.
2. Align holes in base tube and umbrella pole. Insert long 1/4-20 machine screw and secure
with lock nut.
CAUTION: Do not let go of the umbrella until the pole has been secured.
WARNING! All 3 seat units must be anchored. All units used with metal umbrellas must be
anchored.
Date: January 31, 2020