Landscape forms Arne User manual

INSTALLATIONPROCEDUREFORLIGHTPOLE:

1. Liftthelightpoleintopositionovertheinstalledanchors(refertoArneanchorkit

installationguide)asshowninFig.1.Ensurethatthebaseplateisrestingonallfour

washers.

2. InstallwasherandhexnutasshowninFig.2.

3. Plumbandlevelthepoleandtightenallanchors.

4. Installluminaire.Refertopage2formountingluminairetopole.

5. Makeelectricalconnections.Refertowiringdiagram.

6. Installthetopcaponthepole(shippedwiththepole).Iftheunithasatwistlock

receptacle,assemblethereceptacleandthetopcapasshowninFig.3andconnect

wiringbeforeinstallingthetopcap.

7. InstallthenutcoversasshowninFig.4.

ToolsRequired

•Safetyglasses

•Wrenches:1‐1/4”for4.5mand6mpolesor1‐5/8”for8m(5in/7in)and10m(5in/8in)pole

•Wiringtoolsandconnectors

•Properpersonnel,craneorliftforhoistingunitontoanchors

•Level

•Dimmingcontrol,ifrequired

•Hexkey5/32”fornutcovers

•Twistlockphotoeye,ifrequired

•4mmand6mmhexkeys

•13mmwrenches

•17mmsocketwrench

LandscapeFormsisnotresponsibleforsitepreparationandfootings.Refertothe

installationguidefortheArnelightanchorkitforinstallingtheanchorbolts.

CAUTION! Thisunitisheavy.Toavoidinjuryordamagetothefinish,werecommendusing

acraneorliftforhoistingtheunitontotheanchors.

WARNING! Polemountedluminairesmustbeattachedeitherbeforeorimmediately after

poleinstallation. Failuretodosomaycausevibrationdamagetothepoleandwillvoidthe

polewarranty.

ASSEMBLEWITHCARE! Toprotectthisfinishduringassembly,placeunwrappedpowdercoated partson

packagingfoamorothernon‐marringsurface.Donotplaceorslidepowdercoated partsonconcreteor

otherhardortexturedsurface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppainton

anygougesinthefinishcausedbyassemblytools.

Fig.2– Installpole

Fig.3– Installtwistlock

receptacletotopcap

Installation Guide

Arne Column mount LED Light

www.landscapeforms.com Ph: 800.521.2546

Date: November 6, 2017

Page 1 of 4

Fig.1–Poleorientation

HANDHOLE

ORIENTEDON

SIDEOPPOSITE

OFLUMINAIRE

SETBACK

SIDEWALK

Fig.4– Installnutcovers

4X‐ Nutcoverwith

1/4‐20x5/8”button

headcapscrew

Polewithbaseplate

4.5m 6m 8m 10m

Twistlockreceptacle,

optional

Polecap

Standard Fortwistlock

Shortingcapfor

Twistlock,optional

luminaire

Columnmount

bracket

Includedcomponents

Installation Guide

Arne Column mount LED Light

www.landscapeforms.com Ph: 800.521.2546

Date: November 6, 2017

Page 2 of 4

Columnmountstep1

Columnmountstep3

OPENGROMMET

Columnmountstep4

MAXTIGHTENING

TORQUE27Nm

Columnmountstep2

ANGULAR

LOCKING

EVERY10°

MAXIMUM

TIGHTENING

TORQUE27Nm

Columnmountstep5

DONOTDISASSEMBLE

THELOWERPART

CABLE:MAXTIGHTENING

TORQUE8Nm

SCREW:MAXTIGHTENING

TORQUE6Nm

LINE‐INPOWERCORD,NOT

INCLUDED.CABLEGLAND

ACCEPTSSIZE5‐12mmDIA

PROCEDUREFORWIRINGARNELEDLUMINAIRES:

TheArneluminaireshipsfullyassembledfromthefactory.

Thewiringschematicsaretobeusedtoconnecttheunittolinevoltage.Itistheresponsibilityoftheinstallertomakesure thatallconnectionsaremadeinaccordancewiththeNEC

andlocalbuildingcodes.