Lantech 5 10/100TX w/ 4 PoE Injector Industrial... User manual

Lantech
5 10/100TX with 4 PoE Injector
Industrial Switch
User Manual
V1.01
Nov-2007

FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Content
Introduction................................................................ 1
Features................................................................... 1
Package Contents.................................................... 2
Hardware Description ............................................... 3
Physical Dimension.................................................. 3
Front Panel .............................................................. 3
Top View.................................................................. 4
LED Indicators ......................................................... 5
Ports......................................................................... 6
Cabling..................................................................... 7
Wiring the Power Inputs........................................... 8
Wiring the Fault Alarm Contact................................ 9
Mounting Installation .............................................. 10
DIN-Rail Mounting.................................................. 10
Wall Mount Plate Mounting.................................... 12
Hardware Installation.............................................. 13
Installation Steps.................................................... 13
Network Application................................................ 14
Troubleshooting ...................................................... 15
Technical Specification........................................... 16

1
Introduction
The 5 10/100TX w/ 4 PoE Injector Industrial Switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications. Besides, the
industrial switch provides the PoE function for kinds of Powered Devices to receive
power as well as data over the RJ-45 cable.
Features
System Interface/Performance
¾RJ-45 ports support Auto MDI/MDI-X Function
¾Embedded 4-port PoE Injection
¾Store-and-Forward Switching Architecture
¾Back-plane (Switching Fabric): 1.0Gbps
¾2K MAC Address Table
Power Supply
¾DC 48V Redundant Power
Case/Installation
¾IP-30 Protection
¾DIN Rail and Wall Mount Design
Provides EFT protection 3,000 VDC for power line
Supports 6,000 VDC Ethernet ESD protection

2
Package Contents
Please refer to the package contents list below to verify them against the checklist.
5 10/100TX w/ 4 PoE Injector Industrial Switch
User manual
Pluggable Terminal Block
2 wall mount plates with screws
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.

3
Hardware Description
In this paragraph, the Industrial switch’s hardware spec, port, cabling information, and
wiring installation will be described.
Physical Dimension
5 10/100TX w/ 4 PoE Injector Industrial Switch dimension (W x D x H) is 30mm x 95mm
x 140mm
Front Panel
The Front Panel of the 5 10/100TX w/ 4 PoE Injector Industrial Switch is shown as below:
Front Panel of the PoE Injectors Industrial Switch

4
Top View
The top view of the 5 10/100TX w/ 4 PoE Injector Industrial Switch has one terminal
block connector of two DC power inputs.
Top View of the PoE Injectors Industrial Switch

5
LED Indicators
The diagnostic LEDs located on the front panel of the industrial switch provide real-time
information of system and optional status. The following table provides the description of
the LED status and their meanings for the switch.
LED Color Description
P1 Green
On Power input 1 is active
Off Power input 1 is inactive
P2 Green
On Power input 2 is active
Off Power input 2 is inactive
Fault Red
On Power input 1 or 2 has failed
Off Power input 1 and 2 are both functional, or no power
inputs
FWD (1 ~ 4) Green On The port is supplying power to the powered-device
Off No powered-device attached or power supplying fails
1 ~ 5 (RJ-45)
Green
(Upper
LED)
On Connected to network
Flashing Networking is active
Off Not connected to network
Yellow
(Lower
LED)
On Full-duplex link
Flashing Collision occurs
Off Half-duplex link or link down

6
Ports
RJ-45 ports
The UTP (RJ-45) Fast Ethernet ports will auto-sense for 10Base-T or 100Base-TX
connections. Auto MDI/MDIX means that the switch can connect to another switch or
workstation without changing straight through or crossover cabling. See the below
figures for straight through and crossover cable schematic.
RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
Note “+” and “-” signs represent the polarity of the wires that make up each wire
pair.
All ports on this industrial switch support automatic MDI/MDI-X operation, user can use
straight-through cables (See figure below) for all network connections to PCs or servers,
or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of
the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the
cable. The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X port pin outs.
Pin MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)

7
Straight Through Cable Schematic
Cross Over Cable Schematic
Cabling
Twisted-pair segment can be connected with unshielded twisted pair (UTP) or
shielded twisted pair (STP) cable. The cable must comply with the IEEE 802.3u
100Base TX standard for Category 5. The cable between the converter and the link
partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.