Lantech IGC-0101DSFP User manual

Lantech
IGC-0101DSFP
IPGC-0101DSFP
10/100/1000T (PoE at) to 100/1000M
SFP Industrial Switch Converter
User Manual
Oct 2020

Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Content
Overview............................................................1
Introduction: IGC-0101DSFP.................................. 1
Introduction: IPGC-0101DSFP................................ 2
Packing List............................................................ 3
Safety Precaution ................................................... 3
Hardware Description.........................................4
Front Panel............................................................. 4
Top View ................................................................ 5
Wiring the Power Inputs.......................................... 5
Wiring the Fault Alarm Contact ............................... 6
LED Indicators........................................................ 7
DIP-Switch.............................................................. 7
Ports....................................................................... 8
Cabling................................................................... 9
Mounting Installation........................................13
DIN-Rail Mounting ................................................ 13
Wall Mount Plate Mounting................................... 15

Rack-mounting ..................................................... 16
Hardware Installation .......................................18
Installation Steps .................................................. 18
Troubles shooting.............................................20

FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. It may cause
harmful interference to radio communications if the equipment is not installed and used in
accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

1
Overview
Introduction: IGC-0101DSFP
The Lantech IGC-0101DSFP is an Industrial Converter converting from
10/100/1000BaseT to 100/1000M-FX dual speed. It supports 10K bytes
jumbo frame.
Auto-sensing LLF and Power Fault LED/relay alarm setting by DIP
switch
Featured with LLF (Link Loss Forwarding) function, Lantech
IPGC-0101DSFP is able to auto cut off connection if one end of
connection is down. When copper port disconnects, it will auto turn off
fiber port. When fiber port disconnects, it will auto turn off copper port.
Smart LLF function alert central side switch immediate remedy action
when connection is lost. Power Fault LED and relay alarm can be off by
DIP switch.
Dual power input from 18V~72VDC/18~36VAC with galvanic
isolation
IGC-0101DSFP supports dual wide range input from 18V~72VDC
(standard model) and 18~36VAC (AC model) with galvanic isolation that
is good for various application including vehicle, railway, solar panel etc.
Hardened design with extended temperature range
It provides ±2000V EFT and ±6000V ESD protection, which can reduce
unstable situation caused by power line and Ethernet. It has high
reliability and robustness coping with extensive EMI/RFI phenomenon,
environmental vibration and shocks usually found in Automation,
transportation, surveillance, Wireless backhaul, Semi-conductor factory
and assembly lines.
The -E model can be used in extreme environments with an operating
temperature range of -40°C to 75°C.
19” Rack mount-able kit for up to 10 converters mounting
The optional 19” rack-mount kit can be mounted with up to 10
converters.

2
Introduction: IPGC-0101DSFP
The Lantech IPGC-0101DSFP is an Industrial Converter converging
from 10/100/1000BaseT to 100/1000M-FX dual speed with 802.3at/af
PoE support. It supports 10K jumbo frame.
Auto-sensing LLF and Power Fault LED/relay alarm setting by DIP
switch
Featured with LLF (Link Loss Forwarding) function, Lantech
IPGC-0101DSFP is able to auto cut off connection if one end of
connection is down. When copper port disconnects, it will auto turn off
fiber port. When fiber port disconnects, it will auto turn off copper port.
Smart LLF function alert central side switch immediate remedy action
when connection is lost. Power Fault LED and relay alarm can be off by
DIP switch
.
Dual DC input power
IPGC-0101DSFP supports dual input from 9.5V~57VDC (12V model) or
44V~56VDC (48V model) for various application including vehicle,
railway, solar panel etc.
Hardened design with extended temperature range
It provides ±2000V EFT and ±6000V ESD protection, which can reduce
unstable situation caused by power line and Ethernet. It has high
reliability and robustness coping with extensive EMI/RFI phenomenon,
environmental vibration and shocks usually found in Automation,
transportation, surveillance, Wireless backhaul, Semi-conductor factory
and assembly lines.
The -E model can be used in extreme environments with an operating
temperature range of -40°C to 75°C.
19” Rack mount-able kit for up to 10 converters mounting
The optional 19” rack-mount kit can be mounted with up to 10
converters.

3
Packing List
1 x 10/100/1000 to Mini-GBIC Industrial Switch Converter
1 x Terminal Block
Safety Precaution
Attention
IF DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.

4
Hardware Description
In this paragraph, we will introduce the Industrial switch converter’s
hardware spec, port, cabling information, and wiring installation.
Front Panel
The Front Panel of the IGC-0101DSFP/IPGC-0101DSFP is shown as
below.
Front Panel of the Industrial Switch Converter

5
Top View
The top panel of the Industrial Switch Converter is equipped one
terminal block connector of two DC power inputs.
Top panel of the Industrial Switch Converter
Wiring the Power Inputs
Please follow the steps below to insert the power wire.
1. Insert the positive and negative wires into the V+ and V- contacts on the
terminal block connector.

6
2. To tighten the wire-clamp screws for preventing the DC wires to loose.
Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of terminal block connector as the
picture shows below. Inserting the wires, it will detect the fault status
which the power is failure or port link failure (for managed model) and form
an open circuit.
Note
The wire gauge for the terminal block should be in the range
between 12~ 24 AWG.
Insert the wires into the fault alarm contact (No. 3 & 4)

7
LED Indicators
There are few LEDs display the power status and network status
located on the front panel of the Industrial switch converter, each of
them has its own specific meaning as below table.
Table 2.1: Industrial Switch Converter LED Definition
LED
Color
Description
PWR1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
PWR2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 has failed
Off
Power input 1 and 2 are both functional,
or no power input
LNK/ACT
(fiber port)
Green
On
Connected to network
Flashing
Networking is active
Off
Not connected to network
PoE
(IPGC only)
Green
On
Link to PD(PoE device)
Off
Link to none PoE device
DIP-Switch
The DIP-Switch is used to configure operation mode for LLF (Link Lost
Forwarding) and power alarm. The default value of DIP-switch is OFF.
Table 2.2: Industrial Switch Converter DIP-Switch Definition
S/W
Status
Description
Fault
ON
Enable Power Alarm
OFF
Disable Power Alarm
SFP
Speed
100M
Set SFP speed as 100M
1000M
Set SFP speed as 1000M

8
Ports
RJ-45 ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for
10Base-T, 100Base-TX or 1000Base-T devices connections. Auto
MDI/MDIX means that you can connect to another switch or workstation
without changing straight through or crossover cabling. See figures as
below for straight through and crossover cable schematic.
RJ-45 Pin Assignments
Pin Number
Assignment
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Note
“+” and “-” signs represent the polarity of the wires that make up
each wire pair.
All ports on this industrial switch converter support automatic
MDI/MDI-X operation, you can use straight-through cables (See Figure
below) for all network connections to PCs or servers, or to other
switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one
end of the cable, are connected straight through to pins 1, 2, 3 and 6 at
the other end of the cable. The table below shows the 10BASE-T/
100BASE-TX /1000Base-T MDI and MDI-X port pin outs.
Pin MDI-X
Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)

9
Straight Through Cable Schematic
Cross Over Cable Schematic
Cabling
Twisted-pair segment can use unshielded twisted pair (UTP) or
shielded twisted pair (STP) cabling. The cable between the link partner
(switch, hub, workstation, etc.) and the converter must be less than 100
meters (328 ft.) long and comply with the IEEE 802.3ab 1000Base-T
standard for Category 5e or above.
Fiber segment using single-mode connector type must use 9/125μm
single-mode fiber cable. You can connect two devices in the distance of
10 km. Fiber segment using multi-mode connector type must use
50/125 or 62.5/125μm multi-mode fiber cable. You can connect two
devices up to 550m distances.
The small form-factor pluggable (SFP) is a compact optical transceiver
used in optical communications for both telecommunication and data
communication applications.
To connect the transceiver and LC cable, please follow the steps shown
below:
First, insert the transceiver into the SFP module. Notice that the triangle
mark is the bottom of the module.

10
Figure 2.8: Transceiver to the SFP module
Figure 2.9: Transceiver Inserted

11
Second, insert the fiber cable of LC connector into the transceiver.
Figure 2.10: LC connector to the transceiver
To remove the LC connector from the transceiver, please follow the steps
shown below:
First, press the upper side of the LC connector from the transceiver and pull it
out to release.
Figure 2.11: Remove LC connector

12
Second, push down the metal loop and pull the transceiver out by the plastic
part.
Figure 2.12: Pull out from the SFP module

13
Mounting Installation
DIN-Rail Mounting
The DIN-Rail is screwed on the industrial switch when out of factory. If
the DIN-Rail is not screwed on the industrial switch, please see the
following figure to screw the DIN-Rail on the switch. Follow the below
steps to hang the industrial switch.
1. Use the screws to screw on the DIN-Rail on the industrial switch
2. To remove the DIN-Rail, reverse the step 1.

14
3. First, insert the top of DIN-Rail into the track.
4. Then, lightly push the button of DIN-Rail into the track.
5. Check the DIN-Rail is tightly on the track.
6. To remove the industrial switch from the track, reverse steps above.

15
Wall Mount Plate Mounting
*Optional Wall Mount Kit required
Follow the steps below to mount the industrial switch with the wall mount
plates included.
1. To remove the DIN-Rail clip from the industrial switch, unscrew the
screws to remove the DIN-Rail clip.
2. Place the wall-mount plates on the rear panel of the industrial switch.
3. Use the screws to secure the wall-mount plates on the industrial
switch.
4. Use the hook holes at the corners of the wall-mount plates to hang the
industrial switch on the wall.
5. To remove the wall-mount plates, reverse the steps above.