Lantech IPES-0008A-12V User manual

Lantech
IPES-0008A-12V
8 10/100TX w/ 8 Booster PoE at/af
Injector Industrial Switch
User Manual
V1.00
Jun 2010

Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Content
Introduction.............................................................. 1
Features................................................................. 1
Technical Specification........................................... 2
Package Contents ................................................. 4
Safety Precaution .................................................. 4
Hardware Description.............................................. 5
Physical Dimension................................................ 5
Front Panel............................................................ 6
Top View................................................................ 6
LED Indicators....................................................... 7
Ports....................................................................... 8
Cabling................................................................... 9
Wiring the Power Inputs ......................................10
Wiring the Fault Alarm Contact...........................12
Mounting Installation..............................................13
DIN-Rail Mounting ................................................13
Wall Mounting.......................................................15
Hardware Installation..............................................16
Installation Steps ..................................................16
Network Application................................................17
Troubleshooting......................................................18

1
Introduction
IPES-0008A-12V Industrial Switch is a cost-effective solution, which meets the high
reliability requirements demanded by industrial applications, and also supports to
operate in the wide temperature -40°C ~ 75°C environments. Besides, the equipment
supports 12V or 48V DC power input and provides the PoE function with 48VDC
output for kinds of Powered Devices to receive power as well as data over an RJ-45
cable.
Features
System Interface/Performance
RJ-45 ports support Auto MDI/MDI-X Function
Embedded 4-port PoE Injection
Store-and-Forward Switching Architecture
Back-plane (Switching Fabric): 1.6Gbps
2K MAC Address Table
Power Input
DC 12V/48V Redundant Power Input
Operating Temperature
Wide Operating Temperature: -40°C ~ 75°C
Case/Installation
IP-30 Protection
Installation in a Pollution Degree 2 environment
DIN Rail and Wall Mount Design
Provides EFT protection 3,000 VDC for power line
Supports 6,000 VDC Ethernet ESD protection

2
Technical Specification
The technical specifications of IPES-0008A-12V Industrial Switch are listed as follows.
Communications
Compatibility
IEEE 802.3, 802.3u, 802.3x, 802.3af
LAN
10/100Base-T
Transmission Speed
Up to 100 Mbps
Interface
Connectors
8 x RJ-45 (8-port 10/100TX)
6-pin removable screw terminal (Power & Relay)
LED Indicators
Unit: Power1, Power2, P-Fail, PoE
Ethernet port: Link/Active, Speed
PoE
Power Output
Per port 48 VDC, 15.4 Watts
Pin Assignment
RJ-45 port #1 ~ # 4 support IEEE 802.3af
End-point, Alternative A mode.
Positive (VCC+): RJ-45 pin 1, 2.
Negative (VCC-): RJ-45 pin 3, 6.
Data (1,2,3,6 )
Power
Power Consumption
10 Watts (Max.); POE Power Budget:240 Watts
(48V input); 90W(12V); 120W(24V input)
Power Input
External Power Supply: DC 12~48V, Redundant
power D12V~DC 48V and connective removable
terminal block.
Fault Output
1 Relay Output

3
Mechanism
Dimensions (WxHxD)
74mm (W) x 115mm (D) x 152mm (H)
Enclosure
IP-30, Metal shell with solid mounting kits
Mounting
DIN-Rail, Wall Mount
Protection
ESD (Ethernet)
6,000 VDC
Surge (EFT for power)
3,000 VDC
Power Reverse
Yes
Overload current protection
Yes
Environment
Operating Temperature
Standard: -20°C~60°C /-4°F~140°F
E models:-40°C~75°C / -40°F~167°F
Operating Humidity
5% ~ 95% (non-condensing)
Storage Temperature
-40 ~ 85oC
Storage Humidity
5% ~ 95% (non-condensing)
Certifications
EMC
FCC Class A
CE EN61000-6-2
CE EN61000-6-4
CE EN61000-4-2 (ESD)
CE EN61000-4-3 (RS)
CE EN61000-4-4 (EFT)
CE EN61000-4-5 (Surge)
CE EN61000-4-6 (CS)
CE EN61000-4-8 (Magnetic Field)
Free Fall
IEC60068-2-32
Shock
IEC60068-2-27
Vibration
IEC60068-2-6

4
Package Contents
Please refer to the package contents list below to verify them against the checklist.
IPES-0008A-12V Industrial Switch (with DIN-Rail Bracket)
User manual
Removable Terminal Block
Optional Wall-mount Kit** (2 wall-mount bracket with screws)
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.
Safety Precaution
Attention
IF DC voltage is supplied by an external circuit, please use a protection
device on the power supply input.

5
Hardware Description
In this paragraph, the Industrial switch’s hardware specs, ports, cabling information, and
wiring installation will be described.
Physical Dimension
IPES-0008A-12V Industrial Switch dimensions (W x D x H) is 48.6mm x 95mm x 140mm,
the detail dimensions as Figure-1
Figure-1: Mechanical Dimensions

6
Front Panel
The Front Panel of IPES-0008A-12V Industrial Switch is shown below Figure-2
Figure-2: Front Panel of the PoE Injectors Industrial Switch
Top View
The top view of IPES-0008A-12V Industrial Switch has one terminal block connector of
two DC power inputs and Relay circuit contact. Please refer to Figure-3 for further
information.
Figure-3: Top View of the PoE Injectors Industrial Switch