Lantronix ION001-A User manual

ION001-A
Single-Slot ION Chassis
Install Guide
Part Number 33419
Revision E March 2022

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 2
Intellectual Property
© 2022 Lantronix, Inc. All rights reserved. No part of the contents of this publication may be transmitted or
reproduced in any form or by any means without the written permission of Lantronix.
Lantronix is a registered trademark of Lantronix, Inc. in the United States and other countries.
All other trademarks and trade names are the property of their respective holders.
Patented: https://www.lantronix.com/legal/patents/; additional patents pending.
Warranty
For details on the Lantronix warranty policy, go to http://www.lantronix.com/support/warranty.
Contacts
Lantronix Corporate Headquarters
48 Discovery, Suite 250
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Tel: [phone], Tel: [phone], or https://www.lantronix.com/technical-support/
Sales Offices
For a current list of our domestic and international sales offices, go www.lantronix.com/about/contact.
Disclaimer
All information contained herein is provided “AS IS.” Lantronix undertakes no obligation to update the
information in this publication. Lantronix does not make, and specifically disclaims, all warranties of any
kind (express, implied or otherwise) regarding title, non-infringement, fitness, quality, accuracy,
completeness, usefulness, suitability or performance of the information provided herein. Lantronix shall
have no liability whatsoever to any user for any damages, losses and causes of action (whether in
contract or in tort or otherwise) in connection with the user’s access or usage of any of the information or
content contained herein. The information and specifications contained in this document are subject to
change without notice.
Revision History
Date
Rev
Notes
6/9/10
A
Initial release.
11/29/16
B
Update power supply PN, tie down, and contact information.
9/27/18
C
Update specifications.
2/26/20
D
Update MTBF.
3/11/22
E
Initial Lantronix rebrand.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 3
Contents
Product Description....................................................................................................................................... 4
Ordering Information ..................................................................................................................................... 4
Optional Accessories (sold separately) .................................................................................................... 4
Features ........................................................................................................................................................ 4
Kit Contents................................................................................................................................................... 4
Power Supply Included ................................................................................................................................. 4
Installation ..................................................................................................................................................... 5
Installing a Slide-In Card........................................................................................................................... 5
Powering the Chassis ............................................................................................................................... 6
Grounding the Chassis ............................................................................................................................. 6
Specifications ................................................................................................................................................ 7
Troubleshooting ............................................................................................................................................ 8
Related Manuals and Help............................................................................................................................ 8
Compliance Information ................................................................................................................................ 9
Declaration of Conformity ......................................................................................................................... 9
FCC Regulations ...................................................................................................................................... 9
Canadian Regulations ............................................................................................................................ 10

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 4
Product Description
The Lantronix ION001-A Single Slot chassis is designed for installing a single Lantronix ION slide-in card.
The ION001-A is a 1-slot ION chassis that is design for network edge deployments, allowing a single ION
card to be deployed as a stand-alone unit. This chassis provides a method of mounting one single-wide
ION slide-in media converter module and includes an external AC power supply.
Ordering Information
Part Number
Description
ION001-A
1-Slot Chassis for the ION Platform, AC Powered. The Single-Slot ION chassis is
intended for installing any 6W or less ION slide-in card.
Optional Accessories (sold separately)
Part Number
Description
SPS-2460-SA
External Power Supply 24-60 VDC and 24-42 VAC RMS. For use with all Lantronix
stand-alone media converters and some chassis.
IONFP
ION Blank face plate
WMBP
Wall Mount Bracket: 5" [127 mm]
WMBD
DIN Rail Mount Bracket: 5″ [127 mm]
SFP Modules
SFP and SFP+ modules supported on some slide-in cards; see the Lantronix SFP
webpage.
Features
•Desktop installation
•Supports WMBP wall mount brackets
•Unmanaged Chassis
•Supports any ION slide-in card that requires 6 Watts or less of power (C4120-1048 is not supported)
•Fan-less design
•External AC power
•Supports IP addressable managed ION slide-in cards
Kit Contents
The ION001-A kit includes:
□One ION001-A Single Slot chassis
□One Power Supply
□One Power Cord
□Four rubber feet
□One documentation postcard
Power Supply Included
To order the corresponding country specific power supply, add the extension from the list below to the
end of the SKU; Ex: ION001-A-NA: -NA = North America, -LA = Latin America, -EU = Europe, -UK = United
Kingdom, -SA = South Africa, -JP = Japan, -OZ = Australia; -BR = Brazil.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 5
Installation
Installing a Slide-In Card
CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the
slide-in card, into the single-slot chassis. Failure to observe this caution could result in damage to the
slide-in card. Note: The maximum power delivery capacity for the ION001-A Single Slot chassis is 6
Watts. To install a slide-in-card into the single-slot chassis:
1. Refer to the user guide that came with the slide-in card to ensure that any DIP switches or jumpers
on the module’s circuit board are set correctly for the site installation.
2. Carefully align the slide-in card to the chassis installation guides and slide it fully into the installation
slot, as shown below.
3. Ensure that the slide-in card is firmly seated inside the chassis.
4. Push in and rotate the attached panel fastener screw to secure the slide-in card to the single-chassis
frame.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 6
Powering the Chassis
To supply power to the single-slot chassis:
1. Connect the barrel connector on the power adapter to the ION001-A back panel Power port.
2. Connect the power adapter plug to AC power.
3. Use the cable tie down to secure the power supply cord and the barrel connector.
4. Verify that the single-slot chassis is powered by observing the lit LED(s) on the installed slide-in card.
See the related slide-in card manual for LED and other details.
For an optional DC power source see the SPS-2460-SA External Power Supply 24-60 VDC and 24-42 VAC
rms go to https://www.lantronix.com/products/sps-2460-sa/.
Grounding the Chassis
The single-slot chassis comes equipped with grounding lugs located on its back panel. They require a
grounding conductor wire terminated with a two-hole, compression-type, grounding connector (not
provided). The grounding wire (must be a copper conductor) is not included with the chassis and must be
provided by the customer/installer. The electrical-conducting path from the single-slot chassis must:
•Flow via the grounding lugs to the common bonding network (CBN) for telecom installations, or to
an alternative approved grounding system (if required) for non-telecom installations.
•Be of sufficiently low impedance to conduct fault currents likely to be imposed on the converter.
•Enable proper operation of any over-current protection devices.
Ground Wire Size
The wire size of the Protective Earth (ground) conductor should be greater than or equal to the wire size
of the power source conductors. The power-source conductor wire size is installation dependent and
sized to accommodate acceptable IR losses between the power source and the device power terminal.
The device terminal block accommodates #6 wire lugs. A #6 wire lug typically terminates #16 - #20 wire;
with #18 most common.
Connecting the Ground Wire
The conductor must be fastened to the grounding lugs with the enclosed antirotation star-washers and
lug-nut fasteners. The torque requirement for the connector lug-nut fastener is specified by the
connector’s manufacturer.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 7
Grounding Method
The conductor must be fastened to the grounding lugs with the enclosed antirotation star-washers and
lug-nut fasteners. The torque requirement for the connector lug-nut fasteners is specified by the
connector’s manufacturer. To properly ground the single-slot chassis:
1. Obtain one (1) two-hole, compression-type, grounding connector.
2. Attach the grounding conductor to the chassis by placing the two-hole connector onto the
grounding lugs and fasten with the enclosed lock washers/lug-nuts at the proper torque (per the
manufacturer’s specification).
3. Attach the opposite end of the grounding conductor to the common-bonding network (CBN) for
telecom, or to earth ground (if required) for non-telecom installations.
Specifications
For Lantronix Model ION001-A Single Slot chassis or equivalent. Note: The ION001-A Single Slot chassis
is Class A compliant.
Status LEDs None, Power indicator is on the slide-in card
Dimensions Width: 4" [102 mm] W x 7.1” [180 mm] D x 1.2” [30.48 mm] (H)
Power Supply External AC/DC power supply included, 120-240VAC input, 12VDC Output
(See selected Slide-In Card manual for power consumption data)
Operating Temp. 0°C to 50°C
Storage Temp. -40°C to +85°C
Humidity 5% to 95% (non-condensing)
Altitude 0 – 10,000 ft.
Weight 2 lbs. [0.9 kg]
Compliance UL listed, EN55022, EN55024, CE Mark, FCC Class A, CISPR Class A
MTBF With Power Supply:
•191,800 hours (MIL-HDBK-217F)
•527,500 hours (Bellcore7 V5.0)
Without Power Supply:
•5,600,000 hours (MIL-HDBK-217F)
•15,500,000 hours (Bellcore7 V5.0)
Warranty Lifetime

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 8
CAUTION: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1,
DS3, Video Coax, etc., are intended to be connected to intrabuilding (inside plant) link segments that are
not subject to lightening transients or power faults. Copper based media ports, e.g., Twisted Pair (TP)
Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to
interbuilding (outside plant) link segments that are subject to lightening transients or power faults.
Failure to observe this caution could result in damage to equipment.
Troubleshooting
1. Is a media converter installed in the single-slot chassis?
NO
• Install a slide-in card, media converter into the single-slot chassis. See the Installation section.
• Proceed to step 2.
YES
• Proceed to step 2.
2. Is the Power LED on the media converter lit?
NO
• Is the power adapter the proper type and cycle frequency for the AC outlet? See the Specifications
section.
• Is the power adapter properly installed in the media converter and in the grounded AC outlet?
• Contact Technical Support.
YES
• Proceed to step 3.
3. Check the power requirement for the installed slide-in card:
• Power requirement must be 6 W or less.
• Contact Technical Support.
Related Manuals and Help
A printed documentation card is shipped with each ION001-A chassis.For Lantronix Documentation,
Firmware, App Notes, etc. go to https://www.lantronix.com/technical-support/.
Note that this manual provides links to third party web sites for which Lantronix is not responsible.
Other ION system and related device manuals include.
1. Product Documentation Postcard, 33504
2. ION Management Module (IONMM) Install Guide, 33420 and User Guide, 33457
3. ION System NID User Guides (33432, 33457, 33472, 33493, 33494, 33495, 33496, 33574)
4. SPS-2460-SA External Power Supply User’s Guide, 33455
5. Focal Point™3.0 Management Application User Guide, 33293
6. Release Notes (firmware version specific)
Note: Information in this document is subject to change without notice.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 9
Compliance Information
Declaration of Conformity
Manufacture’s Name: Lantronics, Inc.
Manufacture’s Address: 48 Discovery, Suite 250, Irvine, California 92618 USA
Declares that the products: ION001-A Series Single-Slot Chassis ION-001A
Conforms to the following Product Regulations:
EMC Directive 2004/108/EC; EN 55022:2006+A1:2007 Class A;
EN55024:1998+A12001+A2:2003; EN61000-3-2; EN6100-3-3; CFR Title 47 Part 15 Subpart B Class A;
Low Voltage Directive: 2006/95/EC
With the technical construction on file at the above address, this product carries the CE Mark
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
Place: Irvine, California
Date: April 27, 2022
Signature: Fathi Hakam
Full Name: Fathi Hakam
Position: Vice President of Engineering
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference. In which case, the user will be
required to correct the interference at the user’s own expense.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 10
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE
NETWORK. Failure to observe this caution could result in damage to the public telephone
network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EGMitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
In accordance with European Union Directive 2002/96/EC of the European Parliament and of the
Council of 27 January 2003, Lantronix will accept post usage returns of this product for proper
disposal. The contact information for this activity can be found in the 'Contact Us' portion of this
document.

Lantronix ION001-A Install Guide
33419 Rev. E https://www.lantronix.com/ 11
Lantronix Corporate Headquarters
48 Discovery, Suite 250
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Online: https://www.lantronix.com/technical-support/
Sales Offices
For a current list of our domestic and international sales offices, go to the Lantronix web site at
www.lantronix.com/about/contact.