LAZBOY Sawyer User manual

Page 1 of 4
Sawyer 6PC Seating Set
Loveseat
Owner’s Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE.
CALL OUR CUSTOMER SERVICE HOTLINE AT
[phone]
8am-5pm (EST), Monday - Friday
La-Z-Boy® is a registered trademark of La-Z-Boy Incorporated and is used under license to
BJI,Inc. © 2017 La-Z-Boy Incorporated.

Page 2 of 4
For warranty and other helpful information, please visit www.lazboyoutdoor.com or call 1-877-592-7514,
Monday-Friday, 8AM-5PM (EST) or email us at [e-mail].
Care and Maintenance
Be careful to never allow water to build up in frames as this will cause corrosion and freeze damage in cold
climates. Wash all frames with a solution of mild soap and water. Rinse with clean water and dry with a soft
absorbent cloth towel. Frames can be treated with a liquid wax for maximum protection against UV rays and/or
salty damp air. If your set includes cushions, slings, and/or an umbrella they may be cleaned by hand with a
solution of soap and water with a clean water rinse. (Never machine wash cushions, slings or umbrella covers
as this will result in shrinkage or damage).
After cleaning cushions tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry
fabric goods).
Do not use bleach or solvents to clean any product! This will void the warranty.
Lack of original receipt will void warranty!
CAUTION: Read all the instructions before assembly.Failure to do so may result in faulty assembly and
potential injury!
Assemble product on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging the item.
Seek assistance to assemble bulky or heavy items.After final alignment, make sure all bolts and nuts are
securely tightened with screw head covers pressed in place.
Note:Do not allow children to play with plastic wraps or small parts to prevent potential choking hazard.
PARTS LIST
PART#
DESCRIPTION
PICTURE
Q’TY
A
Seat Frame
1
B
Seat
1
C
Bolt M6 x 15MM
6
D
M6 Washer
6
E
M6 Bolt Cover
6

Page 3 of 4
F
Open Wrench
2
G
Seat Cushion
2
H
Back Cushion
2
I
Toss P i l l o w
2
Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Place the seat frame (A) on a flat surface.(Figure 1)
Figure 1
Step 2. With the help of another person, carefully place the seat (B) into the seat frame.
Connect the seat to the seat frame with bolts (C), washers (D) by using open wrench (F), then
cover the bolts with bolt covers (E). (Figure 2&3)
Figure 2 Figure 3

Page 4 of 4
Step 3.Place the seat cushions (G), back cushions (H) and the toss pillows (I) on the seat. Your
loveseat is now ready to use. (Figure 4 )
Figure 4
Look under lounge chairs and ottomans for cushions.

Page 1 of 6
Sawyer 6PC Seating Set
Coffee Table
Owner’s Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE.
CALL OUR CUSTOMER SERVICE HOTLINE AT
[phone]
8am-5pm (EST), Monday - Friday
La-Z-Boy® is a registered trademark of La-Z-Boy Incorporated and is used under license to
BJI,Inc. © 2017 La-Z-Boy Incorporated.

Page 2 of 6
For warranty and other helpful information, please visit www.lazboyoutdoor.com or call 1-877-592-7514,
Monday-Friday, 8AM-5PM (EST) or email us at [e-mail].
Care and Maintenance
Be careful to never allow water to build up in frames as this will cause corrosion and freeze damage in cold
climates. Wash all frames with a solution of mild soap and water. Rinse with clean water and dry with a soft
absorbent cloth towel. Frames can be treated with a liquid wax for maximum protection against UV rays and/or
salty damp air. If your set includes cushions, slings, and/or an umbrella they may be cleaned by hand with a
solution of soap and water with a clean water rinse. (Never machine wash cushions, slings or umbrella covers
as this will result in shrinkage or damage).
After cleaning cushions tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry
fabric goods).
Do not use bleach or solvents to clean any product! This will void the warranty.
Lack of original receipt will void warranty!
CAUTION: Read all the instructions before assembly.Failure to do so may result in faulty assembly and
potential injury!
Assemble product on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging the item.
Seek assistance to assemble bulky or heavy items.After final alignment, make sure all bolts and nuts are
securely tightened with screw head covers pressed in place.
Note:Do not allow children to play with plastic wraps or small parts to prevent potential choking hazard.

Page 3 of 6
PARTS LIST
PART#
DESCRIPTION
PICTURE
Q’TY
A
Table R i m with Gl a s s
1
B
Table L e g
4
C
Short Leg Connector
2
D
Long Leg Connector
2
E
Leg Connecting Plate
1
F
M6 x 15 Bolt
20
G
Washer
20
H
Cover
20
I
Open Wrench
2
Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Take the glass out from table rim then put it on a soft surface.
Step 2. Carefully place the table rim (A) upside down on a non-abrasive surface.(Figure 1)
Figure 1

Page 4 of 6
Step 3.Then loosely attach the legs (B) to the table top (A) with bolts (F) and washers (G) by
using open wrench (I). (Figure 2 )
Figure 2
Step 4. Attach short leg connector (C) to table legs (B) with bolts (F) and washers (G) by using
open wrench (I). (Figure 3 )
Figure 3
Step 5. Then assemble one of the long leg connector (D) to the table legs (B) with bolts (F) and
washers (G) by using open wrench (I). (Figure 4 )
Figure 4

Page 5 of 6
Step 6. Insert the leg connecting plate (E) to the one of the long leg connector (D). (Figure 5)
Figure 5
Step 7. Then insert the leg connecting plate (E) to the other long leg connector(D) and at the
same time assemble the long leg connector to the table legs with bolts (F) and Washers (G).
(Figure 6)
Figure 6
Step 8. Check the alignment of all table legs (B) and adjust if necessary. Once the alignment is
correct, tighten all bolts (F) with open wrench (I).
Step 9. Cover all bolts (F) with bolt covers (H). Then carefully turn the table right side up.
Step 10. Place the glass on the table rim as shown in figure 7. Your table is now ready to use.
(Figure 7)
Figure 7

Page 6 of 6
Warning:
a..Do not crawl, stand, or sit on glass table tops.
b..Do not set or lay heavy items on glass table tops.
c..Avoid extreme hot & cold items being placed on glass table tops.
d..This glass table top is produced with tempered glass which is designed to
safely shatter in small pieces when impacted or stressed beyond strength
limitations.