LD DAVE G3 SERIES User manual

USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D´UTILISATION
MANUAL DE USUARIO
INSTRUKCJA OBSŁUGI
MANUALE D´USO
STINGER G3 SERIES
ACTIVE LOUDSPEAKER
LDEB82AG3 / LDEB102AG3 / LDEB122AG3 / LDEB152AG3
LDEB282AG3

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO
ENGLISH
PREVENTIVE MEASURES 3-4
INTRODUCTION 4-5
CONNECTIONS, CONTROLS AND INDICATORS 5-8
STAND FLANGE 8
USE AS A STAGE MONITOR 8
OPTIONAL ACCESSORIES 8-9
TECHNICAL SPECIFICATIONS 8-10
MANUFACTURER INFORMATION 11
DEUTSCH
SICHERHEITSHINWEISE 12-13
EINFÜHRUNG 13
ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 14-16
STATIVFLANSCH 17
VERWENDUNG ALS BÜHNENMONITOR 17
OPTIONALES ZUBEHÖR 17-18
TECHNISCHE DATEN 18-19
HERSTELLERERKLÄRUNGEN 20
FRANCAIS
MESURES PRÉVENTIVES 21-22
INTRODUCTION 22
CONNECTEURS, CONTRÔLES ET INDICATEURS 23-25
PUITS POUR PIED 26
UTILISATION COMME RETOUR DE SCÈNE 26
ACCESSOIRES OPTIONNELS 26-27
CARACTÉRISTIQUES TECHNIQUES 27-28
DÉCLARATIONS FABRICANT 29
ESPAÑOL
MEDIDAS DE SEGURIDAD 30-31
INTRODUCCIÓN 31
CONEXIONES, CONTROLES E INDICADORES 32-34
ADAPTADOR DE SOPORTE 35
USO COMO MONITOR DE ESCENARIO 35
ACCESORIOS OPCIONALES 35-36
CARACTERÍSTICAS TÉCNICAS 36-37
DECLARACIÓN DEL FABRICANTE 38
POLSKI
ŚRODKI OSTROŻNOŚCI 39-40
WPROWADZENIE 40
ZŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 41-43
KOŁNIERZ STATYWU 44
ZASTOSOWANIE JAKO MONITOR SCENICZNY 44
OPCJONALNE AKCESORIA 44-45
DANE TECHNICZNE 45-46
DEKLARACJE PRODUCENTA 47
ITALIANO
INDICAZIONI SULLA SICUREZZA 48-49
INTRODUZIONE 49
CONNESSIONI, ELEMENTI DI COMANDO E VISUALIZZAZIONE 50-52
FLANGIA PER STATIVO 53
UTILIZZO COME MONITOR DA PALCOSCENICO 53
ACCESSORI OPZIONALI 53-54
DATI TECNICI 54-55
DICHIARAZIONI DEL FABBRICANTE 56

ITALIANOPOLSKIESPAÑOL
FRANCAISDEUTSCHENGLISH
3
ENGLISH
YOU‘VE MADE THE RIGHT CHOICE!
We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience
as a manufacturer of high-quality audio products. Please read this User‘s Manual carefully, so that you can begin making optimum use of
your LD Systems product quickly.
You can find more information about LD-SYSTEMS at our Internet site WWW.LD-SYSTEMS.COM
PREVENTIVE MEASURES
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall mounts are properly installed and
secured. Make certain that the equipment is installed securely and cannot fall down.
7. During installation, observ e the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always
installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Keep a minimum distance of 20 cm around and above the device.
12. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in this case, observe the
special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases. Avoid direct sunlight!
13. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with liquids, such as vases or
drinking vessels, on the equipment.
14. Make certain that objects cannot fall into the device.
15. Use this equipment only with the accessories recommended and intended by the manufacturer.
16. Do not open or modify this equipment.
17. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
18. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.
19. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or if it has been damaged in anot
her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by
authorized, qualified personnel.
20. Clean the equipment using a dry cloth.
21. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.
22. Plastic bags must be kept out of reach of children.
23. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority
to operate the equipment.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS
24. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective
ground. Never deactivate the protective ground of a power cord.
25. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do not switch it on immediately.
Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.
26. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the
equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the
mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.
27. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power
adapter and the equipment connector.
28. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the
equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and
power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter
with wet hands.
29. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of
the equipment.
30. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an
authorised service centre.
31. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.
32. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed.
However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or
other damage. For this reason, always be careful when laying cables.
33. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

4
DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
CAUTION:
To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts
inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an
electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation.After use, wait for a
cool-down period of at least 10 minutes before handling or transporting the device.
Warning! This device is designed for use below 2000 metres in altitude.
Warning! This product is not intended for use in tropical climates.
CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!
This device is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident
prevention rules and regulations. As a manufacturer,Adam Hall is obligated to notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL)
that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged exposure to
volumes in excess of 90 dB.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INTRODUCTION
Stinger®G3 Series - Workhorse Loudspeakers For Pros
Exceptional sound, reliable performance and unparalleled value across the board - that’s LD Systems’ Stinger®G3 Series.
Real workhorses for demanding applications, these loudspeakers have been engineered to provide truly professional
sound reinforcement solutions. The Stinger®G3 line includes active and passive models that are simply outstanding in
their class. Custom designed drivers with high power handling and BEM modelled waveguides deliver immaculate audio
quality, extended low frequency response and coherent coverage.
Sporting lightweight Class D power stages, active Stinger®G3 models are capable of huge sound pressure levels.The multi-purpose
tops feature up to a massive 500 watts RMS output and carefully tailored presets for flat response, fullrange, satellite or floor monitor
applications. LD Systems’ proprietary DynX®DSP technology ensures perfect time alignment and distortion-free performance even
at maximum levels. Producing tremendous low end punch and definition with up to 800 watts RMS output power, Stinger®G3
subwoofers include user-friendly presets for rapid system integration and cardioid array configurations.

ITALIANOPOLSKIESPAÑOL
FRANCAISDEUTSCHENGLISH
5
CONNECTIONS, CONTROLS AND INDICATORS
8
7
4
5
3
2 2
11
6
3
1INPUT LINE / MIC CH 1 & 2
Balanced microphone or line input (XLR / 6.3 mm jack combo) for channels 1 and 2 (CH 1 + CH 2). It is also possible to use unbalanced
microphone cables (Mono jack). Switching to the corresponding setting is done using the MIC / LINE N 3 switch.
2GAIN CH 1 & 2
Volume controller for channels 1 and 2 (CH 1 + CH 2).Turning the controller to the left decreases the volume; turning it to the right increases it.
3LINE / MIC
Switch for switching the input impedance and the signal boost for channels 1 and 2 (CH 1 + CH 2). Please set the volume controller of the
corresponding channel to minimum (left stop) before connecting a playback device or microphone. To connect a playback device with a
line level (e.g. mixer, keyboard), select the LINE setting (LED indicator MIC is not lit); to connect a microphone, select the MIC setting (LED
indicator MIC is lit).
4MODE
Switch to switch between DSP presets. The different presets are retrieved by repeatedly pressing the switch (check the LED indicator).
FULL-RANGE: Preset for operating the loudspeaker without any additional subwoofer (bass boost, presence cut and treble boost).
SATELLITE: Optimal setting for operating with a subwoofer (high-pass filter at 90 hertz, presence cutback and treble boost).
MONITOR: Preset for operating the speaker as a stage monitor (bass cutback to compensate for ground coupling,
treble cutback for optimum, prominent sound at close range).
FLAT: Linear frequency response in DSP preset when using an external equaliser for manual adjustment to the sound situation at hand.
All Stinger®G3 enclosures are made of rigid, low-resonance birch ply. They are coated with non-abrasive, impact resistant
polyurea for superior strength and unrivaled durability. Integrating LD Systems’ Dual-Tilt pole mount, multiple suspension
points, stacking recesses and ergonomic handles the Stinger®G3 Series has been designed for touring musicians, rental
companies and installation applications. The large selection of Stinger®accessories includes smart wall and truss mounting
hardware plus a stackable dolly board to facilitate transport. Isn’t it time you saddled up?

6
DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
FULL-RANGE
20 Hz 100 Hz 1 kHz 20 kHz
20 Hz 100 Hz 1 kHz 20 kHz
SATELLITE
20 Hz 100 Hz 1 kHz 20 kHz
MONITOR
20 Hz 100 Hz 1 kHz 20 kHz
FLAT

ITALIANOPOLSKIESPAÑOL
FRANCAISDEUTSCHENGLISH
7
5STATUS LEDS
ON: Lights up once the system is properly connected to the power mains and switched on.
SIGNAL: Lights up as soon as an audio signal is present.
LIMIT: Lights up if the loudspeaker system is operating in the clipping range. A short flash of the LED in this instance is
not critical. To protect the system, an excessive signal level is gently turned down by the built-in limiters.
If the limiter LED lights up permanently or for longer periods, reduce the volume level. Failure to do so may result in a distorted
sound and damage to the speaker system.
PROTECT: Lights up if the system is overloaded/overheated. The amplifiers are muted automatically. Upon
reaching normal operating conditions, the device reverts to normal operating mode after a few minutes.
6LINE OUT MONO MIX
Balanced line output with 3-pin male XLR socket. The incoming signal consists of a mix of signals from channels 1 and 2 (CH 1 + CH 2).
7POWER
Blue power input socket for power supply to the device. A suitable power cable is included.
8POWER ON / OFF
On / Off switch for the power supply of the device.
WHAT DOES LD SYSTEMS DynX®DSP STAND FOR?
DSP stands for Digital Signal Processing, DynX® comprises the Limiter, EQ, Compressor and Crossover features. The digital signal processing
ensures maximum audio performance with maximum clarity and protects the PA system from overload.
WHAT EXACTLY DOES DynX®DSP DO?
The limiter function protects the speakers and prevents distortions caused by overload. Separate limiters for the bass, midrange and high
range attenuate the signal when the level exceeds a value which could have a negative effect. Each limiter is optimised for one of the
three seamlessly contiguous frequency ranges (multi-band limiter). The system can be operated in this manner with a higher overall sound
pressure as extreme peaks are automatically lowered, so that the total volume does not need to be reduced.
The Multiband EQ works over the entire frequency range and optimises the overall sound of the system.
The crossovers divide the audio signal according to the frequency range of the respective speakers, namely the subwoofer and the
tweeter. The amplitude and running-time optimisation of the crossover ensures that all frequencies are output evenly and reach the listener
at the same time.

8
DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
STAND FLANGE
The speakers have a stand flange with a 0° angle socket (rear position) and a socket with a 5° tilt angle (front position). Examples of use:
Use the socket with a 0° angle for standing audiences and the socket with a 5° tilt angle for seated audiences.
USE AS A STAGE MONITOR
Thanks to the monitor DSP preset and the universal housing, the EB102AG3, EB122AG3 and EB152AG3 models can also be used as
fully-fledged stage monitors. Non-slip rubber rails provide stability; the monitor tilt angle is 54°.
OPTIONAL ACCESSORIES
The speakers in the Stinger G3 Series feature several flying and mounting points. Wall and ceiling mounts, clamps and U-brackets are
available as optional accessories, as well as durable protective covers for all models.
LDEB82AG3: Protective Cover Item No.: LDEB82G3PC
Swivel wall mount Item No.: LDEB82G3WMB
Tilt and swivel wall mount Item No.: LDEB82G3WMB1
Truss Super Clamp Item No.: LDEBG3SCP
LDEB102AG3: Protective Cover Item No.: LDEB102G3PC
Swivel wall mount Item No.: LDEB102G3WMB
Tilt and swivel wall mount Item No.: LDEB102G3WMB1
Truss Super Clamp Item No.: LDEBG3SCP
LDEB122AG3: Protective Cover Item No.: LDEB122G3PC
Swivel wall mount Item No.: LDEBG3WMB
Tilt and swivel wall mount Item No.: LDEBG3WMB1
EasyMount®Fly Bracket Item No.: LDEBG3TMB

ITALIANOPOLSKIESPAÑOL
FRANCAISDEUTSCHENGLISH
9
TECHNICAL SPECIFICATIONS
Model number: LDEB82AG3 LDEB102AG3 LDEB122AG3 LDEB152AG3 LDEB282AG3
Product type: PA loudspeaker PA loudspeaker PA loudspeaker PA loudspeaker PA loudspeaker
Type: active active active active active
Low/mid driver
dimensions:
8“ 10“ 12“ 15“ 2 x 8"
Low/mid driver
dimensions (mm):
203.2mm 254mm 304.8mm 381mm 2 x 381mm
Woofer magnet: Ferrite Ferrite Ferrite Ferrite Ferrite
Woofer brand: Custom-made Custom-made Custom-made Custom-made Custom-made
Woofer voice coil: 2“ 2“ 2.5“ 3“ 2"
Woofer voice coil
(mm):
50.8 mm 50.8 mm 63.5 mm 76.2 mm 50.8mm
Horn: BEM optimzed CD
horn
BEM optimzed CD
horn
BEM optimzed CD
horn
BEM optimzed CD
horn
BEM optimzed CD
horn
HF driver dimensions: 1“ 1“ 1“ 1“ 1"
HF driver dimensions
(mm):
25.4 mm 25.4 mm 25.4 mm 25.4 mm 25.4mm
HF driver magnet: Ferrite Ferrite Ferrite Ferrite Ferrite
HF driver brand: BMS BMS BMS BMS BMS
HF driver voice coil: 1“ 1“ 1“ 1“ 1"
HF driver voice coil
(mm):
25.4mm 25.4 mm 25.4 mm 25.4 mm 25.4mm
Amplifier: Class D Class D Class D Class D Class D
Dispersion (H x V): 90 x 50° 90 x 50° 90 x 50° 90 x 50° 90 x 50°
Power RMS: 300 W 300 W 500 W 500 W 500W
Peak power: 600 W 600 W 1000 W 1000 W 1000W
Frequency response: 70 - 20000 Hz 65 - 20000 Hz 58 - 20000 Hz 50 - 20000 Hz 58 - 20000Hz
Max. SPL (peak): 125 dB 127 dB 131 dB 133 dB 131dB
Protection circuits: Over voltage,
over-current, tem-
perature, multiband
peak limit (DYNX)
Over voltage,
over-current, tem-
perature, multiband
peak limit (DYNX)
Over voltage,
over-current, tem-
perature, multiband
peak limit (DYNX)
Over voltage,
over-current, tem-
perature, multiband
peak limit (DYNX)
over voltage,
over-current, tem-
perature, multiband
peak limit (DYNX)
Input sensitivity: - 9dBu - 9dBu - 5dBu - 5dBu - 5dBu
Controls: 2 x Gain, Mode, 2 x
MIC/LINE
2 x Gain, Mode, 2 x
MIC/LINE
2 x Gain, Mode, 2 x
MIC/LINE
2 x Gain, Mode, 2 x
MIC/LINE
2 x Gain, Mode, 2 x
MIC/LINE
Indicators: On, signal, limit,
protect, mode (full-
range, satellite,
monitor, flat), MIC
On, signal, limit,
protect, mode (full-
range, satellite,
monitor, flat), MIC
On, signal, limit,
protect, mode (full-
range, satellite,
monitor, flat), MIC
On, signal, limit,
protect, mode (full-
range, satellite,
monitor, flat), MIC
On, Signal, Limit,
Protect, Mode (Full-
range, Satellite,
Monitor, Flat), MIC
Line/ Mic inputs: 2 x (switchable) 2 x (switchable) 2 x (switchable) 2 x (switchable) 2 x (switchable)
Line/ Mic input
connectors:
XLR, 6.3 mm jack XLR, 6.3 mm jack XLR, 6.3 mm jack XLR, 6.3 mm jack XLR, 6.3 mm Jack
LDEB152AG3: Protective Cover Item No.: LDEB152G3PC
Swivel wall mount Item No.: LDEBG3WMB
Tilt and swivel wall mount Item No.: LDEBG3WMB1
EasyMount®Fly Bracket Item No.: LDEBG3TMB
LDEB282AG3: Protective Cover Item No.: LDEB282G3PC
Swivel wall mount Item No.: LDEB282G3WMB
Tilt and swivel wall mount Item No.: LDEB282AG3WMB1
Truss Super Clamp Item No.: LDEBG3SCP

10
DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
Line outputs: 1 1 1 1 1
Line output connec-
tors:
XLR XLR XLR XLR XLR
Operating voltage: 100 V AC - 120
V AC /
200 V AC - 240 V
AC, 50 - 60 Hz (au-
tomatic conversion)
SMPS
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
Power consumption
(max.):
300 VA 300 VA 600 VA 600 VA 600 VA
Ambient temperature
(in operation):
0° - 40°C 0° - 40°C 0° - 40°C 0° - 40°C 0° - 40°C
Relative humidity
(in operation):
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
Cabinet material: 12 mm Plywood 12 mm Plywood 15 mm Plywood 15 mm Plywood 12 mm Plywood
Cabinet surface: Polyurea Polyurea Polyurea Polyurea Polyurea
Cabinet construction: vented vented vented vented vented
Monitor angle: n.a. 54° 54° 54° n.a.
Width: 270mm 325mm 390mm 480mm 270mm
Height: 457mm 527mm 627mm 737mm 756mm
Depth: 290mm 308mm 377mm 455mm 290mm
Weight: 10.5 kg 12.7 kg 20.1 kg 26.8 kg 20.5 kg
Features: M10 thread for
superclamp, ergo-
nomically shaped
insert handle,
aluminium dual-tilt
flange (0°/ 5°),
prepared for u-frame
wall mount, prepared
for gravity multi
purpose wall mount
M10 thread for
superclamp, ergo-
nomically shaped
insert handle,
aluminium dual-tilt
flange (0°/ 5°),
prepared for u-frame
wall mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
2 x ergonomically
shaped insert
handles, aluminium
dual-tilt flange (0°/
5°), multifunctional
cabinet design,
rugged steel grille,
flying points, poly-
urea coating, quick-
mount flying frame
adapter, prepared
for u-frame wall
mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
2 x ergonomically
shaped insert
handles, aluminium
dual-tilt flange (0°/
5°), multifunctional
cabinet design,
rugged steel grille,
flying points, poly-
urea coating, quick-
mount flying frame
adapter, prepared
for u-frame wall
mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
M10 Thread for
SuperClamp, 2
x ergonomically
shaped insert
handles, aluminium
Dual-tilt flange
(0°/ 5°), rugged
steel grille, flying
points, polyurea
coating, prepared for
U-frame wall mount,
prepared for Gravity
multi purpose wall
mount

ITALIANOPOLSKIESPAÑOL
FRANCAISDEUTSCHENGLISH
11
Line outputs: 1 1 1 1 1
Line output connec-
tors:
XLR XLR XLR XLR XLR
Operating voltage: 100 V AC - 120
V AC /
200 V AC - 240 V
AC, 50 - 60 Hz (au-
tomatic conversion)
SMPS
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
SMPS, 100 V AC -
120 V AC / 200 V
AC - 240 V AC, 50
- 60 Hz (automatic
conversion)
Power consumption
(max.):
300 VA 300 VA 600 VA 600 VA 600 VA
Ambient temperature
(in operation):
0° - 40°C 0° - 40°C 0° - 40°C 0° - 40°C 0° - 40°C
Relative humidity
(in operation):
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
<80% (non con-
densing)
Cabinet material: 12 mm Plywood 12 mm Plywood 15 mm Plywood 15 mm Plywood 12 mm Plywood
Cabinet surface: Polyurea Polyurea Polyurea Polyurea Polyurea
Cabinet construction: vented vented vented vented vented
Monitor angle: n.a. 54° 54° 54° n.a.
Width: 270mm 325mm 390mm 480mm 270mm
Height: 457mm 527mm 627mm 737mm 756mm
Depth: 290mm 308mm 377mm 455mm 290mm
Weight: 10.5 kg 12.7 kg 20.1 kg 26.8 kg 20.5 kg
Features: M10 thread for
superclamp, ergo-
nomically shaped
insert handle,
aluminium dual-tilt
flange (0°/ 5°),
prepared for u-frame
wall mount, prepared
for gravity multi
purpose wall mount
M10 thread for
superclamp, ergo-
nomically shaped
insert handle,
aluminium dual-tilt
flange (0°/ 5°),
prepared for u-frame
wall mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
2 x ergonomically
shaped insert
handles, aluminium
dual-tilt flange (0°/
5°), multifunctional
cabinet design,
rugged steel grille,
flying points, poly-
urea coating, quick-
mount flying frame
adapter, prepared
for u-frame wall
mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
2 x ergonomically
shaped insert
handles, aluminium
dual-tilt flange (0°/
5°), multifunctional
cabinet design,
rugged steel grille,
flying points, poly-
urea coating, quick-
mount flying frame
adapter, prepared
for u-frame wall
mount, prepared
for gravity multi
purpose wall mount,
monitor rubber
rail feet
M10 Thread for
SuperClamp, 2
x ergonomically
shaped insert
handles, aluminium
Dual-tilt flange
(0°/ 5°), rugged
steel grille, flying
points, polyurea
coating, prepared for
U-frame wall mount,
prepared for Gravity
multi purpose wall
mount
MANUFACTURER´S DECLARATIONS
MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY
You can find our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Decla-
rations-LDSYSTEMS_DE_EN_ES_FR.pdf. To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,
61267 Neu Anspach / Email: [email protected] / +49 (0)6081 / 9419-0.
CORRECT DISPOSAL OF THIS PRODUCT
(valid in the European Union and other European countries with a differentiated waste collection system)
This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid
environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste
and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased
this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed
with other commercial waste for disposal.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation
CE Compliance
Adam Hall GmbH states that this product meets the following guidelines (where applicable):
R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017
Low voltage directive (2014/35/EU)
EMV directive (2014/30/EU)
RoHS (2011/65/EU)
The complete declaration of conformity can be found at www.adamhall.com.
Furthermore, you may also direct your enquiry to [email protected].