LeCroy WaveAce 1000 series User manual

Operator’s Manual
WaveAce 1000/2000
Series Oscilloscopes

WaveAce 1000/2000
Oscilloscopes
Operator's Manual
May, 2012

LeCroy Corporation
700 Chestnut Ridge Road
Chestnut Ridge, NY, 10977-6499
Tel: [phone], Fax: [phone]
Warranty
NOTE: THE WARRANTY BELOW REPLACES ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS, OR ADEQUACY FOR ANY PARTICULAR PURPOSE OR USE. LECROY SHALL NOT BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN CONTRACT OR OTHERWISE. THE CUSTOMER IS RESPONSIBLE FOR THE
TRANSPORTATION AND INSURANCE CHARGES FOR THE RETURN OF PRODUCTS TO THE SERVICE FACILITY. LECROY WILL RETURN ALL PRODUCTS
UNDER WARRANTY WITH TRANSPORT PREPAID.
The oscilloscope is warranted for normal use and operation, within specifications, for a period of three years from shipment. LeCroy will either
repair or, at our option, replace any product returned to one of our authorized service centers within this period. However, in order to do this we
must first examine the product and find that it is defective due to workmanship or materials and not due to misuse, neglect, accident, or abnormal
conditions or operation.
LeCroy shall not be responsible for any defect, damage, or failure caused by any of the following: a) attempted repairs or installations by personnel
other than LeCroy representatives or b) improper connection to incompatible equipment, or c) for any damage or malfunction caused by the use of
non-LeCroy supplies. Furthermore, LeCroy shall not be obligated to service a product that has been modified or integrated where the modification
or integration increases the task duration or difficulty of servicing the oscilloscope. Spare and replacement parts, and repairs, all have a 90-day
warranty.
The oscilloscope's firmware has been thoroughly tested and is presumed to be functional. Nevertheless, it is supplied without warranty of any kind
covering detailed performance. Products not made by LeCroy are covered solely by the warranty of the original equipment manufacturer.
Internet: www.lecroy.com
© 2012 by LeCroy Corporation. All rights reserved.
Unauthorized duplication of LeCroy documentation materials other than for internal sales and distribution
purposes is strictly prohibited. However, clients are encouraged to distribute and duplicate LeCroy
documentation for their own internal educational purposes.
LeCroy, ActiveDSO, JitterTrack, WavePro, WaveMaster, WaveSurfer, WaveLink, WaveExpert, Waverunner, and
WaveAce are registered trademarks of LeCroy Corporation. Other product or brand names are trademarks or
requested trademarks of their respective holders. Information in this publication supersedes all earlier
versions. Specifications are subject to change without notice.
Manufactured under an ISO
9000 Registered Quality
Management System.
Visit www.lecroy.com to
view the certificate.
This electronic product is subject to disposal and
recycling regulations that vary by country and region.
Many countries prohibit the disposal of waste
electronic equipment in standard waste receptacles.
For more information about proper disposal and
recycling of your LeCroy product, please visit
www.lecroy.com/recycle.
WA1K2K-OM-E RevB
920673-00 RevB

WaveAce 1000/2000
WA1K2K-OM-E RevB i
TABLE OF CONTENTS
Welcome ........................................................................iv
Contact LeCroy for Support .......................................... iv
Thank You ..................................................................... iv
WaveAce 1000/2000 Models........................................... 1
Safety Requirements....................................................... 2
Safety Symbols............................................................... 2
Operating Environment ................................................. 4
Safety Certification ........................................................ 4
Cooling ........................................................................... 5
AC Power Source............................................................ 6
Power Consumption ...................................................... 6
Power and Ground Connections.................................... 6
Fuse Replacement........................................................... 8
(For Only WaveAce 2000 Models Only)......................... 8
Calibration...................................................................... 8
Cleaning ......................................................................... 8
Abnormal Conditions ..................................................... 9
Hardware ..................................................................... 10
Front Panel................................................................... 10
Back and Side Connections.......................................... 10
Basic Controls ............................................................... 12
Powering Up Your WaveAce........................................ 12
Front Panel Controls .................................................... 13
Probes .......................................................................... 20
Probes .......................................................................... 20
Probe Compensation ................................................... 20

Operator's Manual
ii WA1K2K-OM-E RevB
Viewing Waveforms...................................................... 21
Turning On Traces........................................................ 21
Setting Up the Display ................................................. 21
Understanding Display Information ............................ 22
Auto Setup ................................................................... 25
Vertical Settings and Channel Controls .......................... 27
Vertical Settings and Channel Controls ....................... 27
Choosing Coupling ....................................................... 27
Limiting Bandwidth...................................................... 28
Adjusting Sensitivity..................................................... 29
Setting Probe Attenuation........................................... 30
Inverting Waveforms ................................................... 31
Setting the Digital Filter ............................................... 31
Unit and Skew Settings ................................................ 32
Acquisition Types.......................................................... 34
Acquisition Types......................................................... 34
Zooming Waveforms ................................................... 37
Triggering ..................................................................... 39
Trigger Types................................................................ 39
Edge Triggering ............................................................ 39
Pulse Triggering ........................................................... 40
Video Triggering........................................................... 41
Slope Triggering ........................................................... 42
Alternative Triggering .................................................. 43
Analyzing Waveforms ................................................... 45
Analyzing Waveforms .................................................. 45
Measuring with Cursors............................................... 45

WaveAce 1000/2000
WA1K2K-OM-E RevB iii
Parameter Measurements........................................... 49
Waveform Math .......................................................... 55
FFT Spectrum Analyzer ................................................ 57
Creating Reference Waveforms................................... 59
Save and Recall............................................................. 62
Saving and Recalling Oscilloscope Settings.................. 62
Saving and Recalling Waveforms................................. 64
Saving and Printing Waveform Pictures ...................... 66
Saving Data as a .CSV File ............................................ 68
Recalling Factory Settings ............................................ 70
Using the SAVE ALL Screen .......................................... 74
Utilities......................................................................... 79
Utility Menu................................................................. 79
Print Setup ................................................................... 88
Updating the System Software.................................... 90
Using Pass/Fail ............................................................. 93
Using Record................................................................ 96
Setting and Displaying the Date/Time ....................... 100
Reference ....................................................................102
Using WaveStudio...................................................... 102
WaveAce Specifications............................................. 105
Certifications.............................................................. 105
CE Declaration of Conformity .................................... 105
UL and cUL ................................................................. 107
China RoHS Compliance............................................. 107
Contact LeCroy for Support ....................................... 109
Index ...........................................................................113

Operator's Manual
iv WA1K2K-OM-E RevB
Welcome
Thank you for purchasing a LeCroy WaveAce product. This Operator's Manual includes
important safety and installation information for your WaveAce 1000/2000 Oscilloscope,
along with operating procedures to get you started capturing, viewing, and analyzing your
waveforms.
This WaveAce Operator's Manual provides information in the following manner:
Get acquainted with your new instrument by reviewing topics covering Hardware
(explaining the physical features of your new instrument) and Basic Controls.
Viewing Waveforms includes instructions on setting up your display and using the
auto setup function.
The next sections provide information on Vertical Settings, Sampling Modes, and
Triggering.
Analyzing Waveforms lists waveform measurements and parameter
measurements. This section also provides procedures for using Math functions and
Creating Reference Waveforms.
Remaining sections cover step-by-step procedures for Saving and Recalling
oscilloscope setups, waveforms, .CSV files, and waveform pictures. This section also
provides procedures to recall factory settings. Finally, we provide a Reference
section including certification and contact information.
Contact LeCroy for Support
When your WaveAce 1000/2000 Oscilloscope is delivered, verify that all items on the
packing list or invoice copy have been shipped to you. Contact your nearest LeCroy
customer service center or national distributor if anything is missing or damaged. If you do
not contact us immediately, we cannot be responsible for replacement. If you have any
problems with your product, please refer to the Contact LeCroy for Support (on page 109)
topic at the end of this Operator's Manual. You can also refer to additional support
materials at www.lecroy.com, or the Online Help (located in the Help menu on your
instrument).
Thank You
We truly hope these materials provide increased comprehension when using LeCroy's fine
products.
Sincerely,
David C. Graef
LeCroy Corporation
Vice President and Chief Technology Officer

WaveAce 1000/2000
WA1K2K-OM-E RevB 1
WaveAce 1000/2000 Models
WaveAce 1000/2000 models are available in two and four channel
versions. The following table shows the two and four channel models and
their rated bandwidths.
Two Channel WaveAce Models
Four Channel WaveAce Models
1001 - 40 MHz
1002 - 60 MHz
1012 - 100 MHz
2002 - 70 MHz
2012 - 100 MHz
2022 - 200 MHz
2032 - 300 MHz
2004 - 70 MHz
2014 - 100 MHz
2024 - 200 MHz
2034 - 300 MHz

Operator's Manual
2 WA1K2K-OM-E RevB
Safety Requirements
This section contains information and warnings that must be observed to
keep the instrument operating in a correct and safe condition. You are
required to follow generally accepted safety procedures in addition to
the safety precautions specified in this section.
Safety Symbols
Where the following symbols appear on the instrument's front or rear
panels, or in this manual, they alert you to important safety
considerations.
This symbol is used where caution is required. Refer to the accompanying
information or documents in order to protect against personal injury or
damage to the instrument.
This symbol warns of a potential risk of shock hazard.
This symbol is used to denote the measurement ground connection.
This symbol is used to denote a safety ground connection.
On (Supply). This is the AC mains connect/disconnect switch at the back
of the instrument (if provided).

WaveAce 1000/2000
WA1K2K-OM-E RevB 3
Off (Supply). This is the AC mains connect/disconnect switch at the back
of the instrument (if provided).
This symbol shows that the switch is a Standby (power) switch located on
the front of the oscilloscope. Pressing this button toggles the
oscilloscope's state between operating and Standby mode. This switch is
not a disconnect device. The instrument can only be placed in a complete
Power Off state by flipping the main power switch on the rear of the
instrument (if provided) to the off (Zero) position or by removing the
power cord. In cases where no main power switch is provided, removing
the main power cord is the disconnect device.
This symbol is used to denote Alternating Current.
CAUTION
The CAUTION sign indicates a potential hazard. It calls attention to a
procedure, practice or condition which, if not followed, could possibly
cause damage to equipment. If a CAUTION is indicated, do not proceed
until its conditions are fully understood and met.
WARNING
The WARNING sign indicates a potential hazard. It calls attention to a
procedure, practice or condition which, if not followed, could possibly
cause bodily injury or death. If a WARNING is indicated, do not proceed
until its conditions are fully understood and met.
CAT I
Installation (Overvoltage) Category rating per EN 61010-1 safety standard
and is applicable for the oscilloscope front panel measuring terminals.
CAT I rated terminals must only be connected to source circuits in which
measures are taken to limit transient voltages to an appropriately low
level.

Operator's Manual
4 WA1K2K-OM-E RevB
Operating Environment
The instrument is intended for indoor use and should be operated in a
clean, dry environment. Before using this product, ensure that its
operating environment is maintained within these parameters:
Temperature: 10 to 40 °C.
Humidity: Maximum relative humidity 80 % for temperatures up to 31 °C
decreasing linearly to 50 % relative humidity at 40 °C (or at the upper
operational temperature limit).
Altitude: Up to 10,000 ft (3,048 m) at or below 25 °C.
Note: Direct sunlight, radiators, and other heat sources should be taken into
account when assessing the ambient temperature.
WARNING
The oscilloscope must not be operated in explosive, dusty, or wet
atmospheres.
CAUTION
Protect the oscilloscope's display touch screen from excessive impacts
with foreign objects.
CAUTION
Do not exceed the maximum specified front panel terminal voltage
ratings. Refer to Specifications for more details. The specifications for
maximum allowable voltages are located on a label on the front of the
oscilloscope.
Safety Certification
The design of the instrument has been verified to conform to applicable
EN 61010-1, UL 61010-1 2nd Edition and CSA C22·2 No·61010-1-04 safety
standards for the following limits:

WaveAce 1000/2000
WA1K2K-OM-E RevB 5
Installation (Overvoltage) Categories II (Mains Supply Connector)
& I (Measuring Terminals).
Pollution Degree 2.
Protection Class I.
PLEASE NOTE THE FOLLOWING:
Installation (Overvoltage) Category II refers to local distribution
level, which is applicable to equipment connected to the mains
supply (AC power source).
Installation (Overvoltage) Category I refers to signal level, which is
applicable to equipment measuring terminals that are connected
to source circuits in which measures are taken to limit transient
voltages to an appropriately low level.
Pollution Degree 2 refers to an operating environment where
normally only dry non-conductive pollution occurs. Conductivity
caused by temporary condensation should be expected.
Protection Class 1 refers to grounded equipment, in which
protection against electric shock is achieved by Basic Insulation
and by means of a connection to the protective ground conductor
in the building wiring.
Cooling
The instrument relies on forced air cooling with an internal fan and
ventilation openings. Care must be taken to avoid restricting the airflow
around the apertures (fan holes) at the sides of the oscilloscope. Ensure
adequate ventilation by leaving the required 5 cm (2 inch) minimum gap
around the sides of the instrument.
CAUTION
Do not block the ventilation holes located on both sides of the
oscilloscope.
CAUTION
Do not allow any foreign matter to enter the oscilloscope through the
ventilation holes, etc.

Operator's Manual
6 WA1K2K-OM-E RevB
AC Power Source
100 to 240 VAC (±10%) at 50/60/400 Hz (+10%); Installation Category:
300V CAT II
No manual voltage selection is required because the instrument
automatically adapts to line voltage.
Power Consumption
< 50 Watts for all models (depending on accessories installed - probes,
USB devices, etc.).
Power consumption in Standby Mode: < 5 Watts.
Power and Ground Connections
The instrument is provided with a 10A/250V 18AWG rated grounded
cord set containing a molded three-terminal polarized plug and a
standard IEC-60320 (Type C13) connector for making line voltage and
safety ground connections. The AC inlet ground terminal is connected
directly to the frame of the instrument. For adequate protection against
electrical shock hazard, the power cord plug must be inserted into a
mating AC outlet containing a safety ground contact.
WARNING - Electrical Shock Hazard
Only use the power cord provided with your instrument.
Any interruption of the protective conductor inside or outside of the
oscilloscope, or disconnection of the safety ground terminal creates a
hazardous situation. Intentional interruption is prohibited.
In Standby mode, the oscilloscope is still connected to the AC supply. The
instrument can only be placed in a complete Power Off state by flipping
the main power switch on the rear of the instrument (if provided) to the
off (Zero) position or by removing the power cord. In cases where no
main power switch is provided, removing the main power cord is the
disconnect device.

WaveAce 1000/2000
WA1K2K-OM-E RevB 7
CAUTION
Always use the Power Switch or File → Shutdowncommand in the
software to properly shut down your instrument. Never substitute this
practice by pulling the instrument power cord from the socket or
shutting down a connected power strip.
CAUTION
The outer conductors of the front panel BNC terminals for all input
channels are connected to the instrument's chassis and therefore to the
safety ground.

Operator's Manual
8 WA1K2K-OM-E RevB
Fuse Replacement
(For Only WaveAce 2000 Models Only)
Set the instrument Standby (power) switch to Standby mode, flip the
mains power switch to the OFF (0) position, and disconnect the power
cord before inspecting or replacing the fuse. Open the black fuse holder
(located at the rear of the instrument below the main power switch)
using a small, flat-bladed screwdriver. Remove the old fuse, replace it
with a new 5 X 20 mm T rated 1.25 A/250 V fuse, and reinstall the fuse
holder.
WARNING
For continued fire protection at all line voltages, replace fuse with the
specified type and rating only. Always disconnect the power cord before
replacing the fuse.
Calibration
The recommended calibration interval is one year. Calibration should be
performed by qualified personnel only.
Cleaning
Clean only the exterior of the instrument, using a damp, soft cloth. Do
not use chemicals or abrasive elements. Under no circumstances allow
moisture to penetrate the instrument.
Avoid electrical shock hazard by unplugging the power cord from the AC
outlet before cleaning.
WARNING - Electrical Shock Hazard
No operator serviceable parts inside.
Do not remove covers.
Refer servicing to qualified personnel.

WaveAce 1000/2000
WA1K2K-OM-E RevB 9
Abnormal Conditions
Operate the instrument only as intended by the manufacturer.
If you suspect the oscilloscope's protection has been impaired,
disconnect the power cord and secure the instrument against any
unintended operation.
The oscilloscope's protection is likely to be impaired if, for example, the
instrument shows visible damage or has been subjected to severe
transport stresses.
Proper use of the instrument depends on careful reading of all
instructions and labels.
WARNING
Any use of the oscilloscope in a manner not specified by the
manufacturer may impair the instrument's safety protection.

Operator's Manual
10 WA1K2K-OM-E RevB
Hardware
Front Panel
The WaveAce 1000/2000 Series oscilloscopes provide an easy-to-use
front panel. The control buttons are logically grouped.
Note: While the following picture is from the 4 Channel version, besides the
extra channels, button and knob locations are essentially the same on the 2
Channel model.
Front panel buttons and knob locations on 4 Channel WaveAce Oscilloscopes. Layout is
very similar on 2 Channel models
Previously numbered front panel buttons and knob locations correspond
with the following explanations.
1. Power Button
2. Front USB (Type A) Connector
3. 1 KHz and Ground Probe Connectors
4. Menu On/Off, Menu Option, and Print Buttons
5. Front Panel Controls
6. Channel and External Trigger Input Connectors
Back and Side Connections
The following image shows back panel connection locations for the 4
Channel models.

WaveAce 1000/2000
WA1K2K-OM-E RevB 11
Back panel connection locations on the 4 Channel WaveAce Oscilloscope.
Previously numbered front panel buttons and knob locations on 4
Channel models correspond with the following explanations.
1. Pass/Fail Output
2. RJ-45 Connector
PLEASE NOTE THE FOLLOWING:
Contact a system administrator when connecting to any
internal LAN.
Use your WaveAce oscilloscope remotely by referring to
Using WaveStudio to Remotely Connect to your WaveAce
Oscilloscope (on page 102).
3. Rear USB (Type B and Type A, respectively) Connectors. Use the
Type B connector to attach a printer to your instrument. The Type
A connector is designated for memory stick use just like the one
on the Front Panel (on page 10).
Note: If you simultaneously connect separate memory sticks to both
the front and back Type A connectors, the WaveAce defaults to only
using the one attached to the front connector.
4. Power Shutoff Switch and Input Connector
5. Security Lock Receptacle
Note: The WaveAce 1000 model has a Power Input Connector and no Power
Shutoff Switch on the left side (facing) of the instrument instead of the back.

Operator's Manual
12 WA1K2K-OM-E RevB
Basic Controls
Powering Up Your WaveAce
1. Power On the oscilloscope by pressing the power button (located
on the lower front of the 2000 models and top left on the 1000
models, when facing the instrument).
2. The LeCroy Splash screen is shown. Press any key to continue (or,
after a brief period the grid display is shown).
3. The Grid Display is shown.

WaveAce 1000/2000
WA1K2K-OM-E RevB 13
Note: The screen size varies slightly between all WaveAce Series
Oscilloscopes. Therefore, the screen-shots in this documentation may
look more narrow or wide than they appear on your specific model.
However, the screens are all functionally the same and the slight
differences have no affect when following these instructions.
Front Panel Controls
Note: While the following pictures are from the 4 Channel version, besides the
extra channels, button and knob locations are essentially the same on the 2
Channel model.
Intensity/Adjust Knob
Intensity/Adjust knob - You can use the Adjust knob with many
functions, such as adjusting the holdoff time, moving cursors,