Led world Hueda h-r009pd Instruction manual

HUEDA™ RF Receiver/Controller

1/4 Copyright © 2016 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

Model: H-R009PD

ŸThis product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the

National Electric Code, and local regulations. Disconnect power before installing or servicing. Only power with a

regulated (listed) constant voltage Class 2 power supply (12-24V DC). Never use this product with dimmable or

magnetic dimmable power source(driver).

ŸEnsure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in

voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could

overheat wires and cause re.

ŸThis product is rated for indoor installation and can be used for dry locations. Avoid the direct sun light.

ŸDo not modify this product beyond the instructions in this guide or the warranty will be voided.

ŸWiring diagrams in this installation guide for basic installations. Please carefully review your installation before

proceeding.

ŸAlways be sure to mount this unit in an area with proper ventilation to avoid overheating.

ŸPlease check if the output voltage of any LED power supplies used comply with the working voltage of the product.

ŸNever connect any cables while power is on and always assure correct connections to avoid short circuits before

switching on.

ŸPlease ensure that the cable is secured tightly in the connector

ŸFor updated information please consult your supplier.

Safety & Warnings

1-800-387-4081

ledworldlighting.com ledworld.ca |

Before you begin, read all warnings and installation instructions (as they may have been updated from previous versions ).

Improper installation(s) present hazards, which can result in personal injury or property damage.

Warning: Input voltage must be identical to output voltage

of the LED Fixture!

Exposed wire should not be more than 6- 8 mm long

tinned. Do not allow Wires to cross and insure all

exposed wire is fully inserted into the terminals. Use 22 to

16 AWG gauge wire for output terminals.

WIRE 6-8MM (0.25-0.30”)

1. Product Operation Overview:

LE D

PRI:

Uin=1 2-36 V D C

Iin=2 0.5A

SEC:

Uout= 4x(12-3 6)VD C

Iout= 4x5A

Pout= 4x(60-1 80)W

LE D C ON TR OL LER

H-R009PD

Lear ning Ke y

Repe ater Si gnal

Receiver Repeater

Jumper

Learning Button Power Input (12/24VDC)

RGBW LED Light Output

V+

V-

Data In/Out

GND

Data+ In

Data- In

Data+ Out

Data- Out

2. Product Parameters:

Part No.

Input Voltage

Current

Output

H-R009PD

12V~36V DC

4 x 5A

4 x (60-180)W

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 03/03/16

2/4 Copyright © 2016 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

Model: H-R009PD 1-800-387-4081

ledworldlighting.com ledworld.ca |

Note: Each hand remote controls 4 zones (areas) and with each zone one can have a maximum

of 8 wireless receivers. Each receiver can be controlled by 8 different remote controllers. If more

than 8 receivers are required in one zone, then please refer to section 5.2 “optional wiring

diagram for direct wire and wireless connections”.

f. The Connected LED light will blink to confirm zone designation and corresponding color will light

Press at learning button on receiver over 5 seconds until LED light flash, unpairs the receiver.

d. Press desired zone button on remote control, then touch color wheel on

remote control .

3.1 Pairing Guide:

b. Turn ON handheld remote control.

c. Press learning button on receiver.

a. Wire according to connection diagram

4. Product Dimension:

156mm (6.14”)

166mm (6.53”)

53.4mm (2.10”)

23mm (0.90”)

3.2 Reset/Unpairing Guide:

HUEDA™ RF Receiver/Controller

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 03/03/16

3/4 Copyright © 2016 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

Model: H-R009PD 1-800-387-4081

ledworldlighting.com ledworld.ca |

Receiver Repeater One receiver can connect multiple repeaters of under 100m (328ft) using

CAT5 wire.

Receiver/Repeater setting jumper

Receiver 1

LE D

PR I :

Uin =1 2- 36 V DC

Iin =2 0. 5A

SE C :

Uou t= 4x (1 2- 36 )V D C

Iou t= 4x 5A

Pou t= 4x (6 0- 18 0) W

LED C O N T R O L L E R

H-R009P D

Lea rni ng K ey

Rep eater S ignal

Class 2 Regulated

Power Supply

12-24VDC

110V-230VAC

Receiver 2 (Repeater)

LE D

PR I :

Uin =1 2- 36 V DC

Iin =2 0. 5A

SE C :

Uou t= 4x (1 2- 36 )V D C

Iou t= 4x 5A

Pou t= 4x (6 0- 18 0) W

LED C O N T R O L L E R

H-R009P D

Lea rni ng K ey

Rep eater S ignal

Receiver 3 (Repeater)

LE D

PR I :

Uin =1 2- 36 V DC

Iin =2 0. 5A

SE C :

Uou t= 4x (1 2- 36 )V D C

Iou t= 4x 5A

Pou t= 4x (6 0- 18 0) W

LED C O N T R O L L E R

H-R009P D

Lea rni ng K ey

Rep eater S ignal

Receiver Repeater

RGB/W LED Strip

RF remote H-2819S

(Optional)

5.2 Optional Wiring Diagram for direct wire and wireless connections

[V+]

[V-]

V+

V-

V+

Power Input

RGBW Output

CAT5 Cable

5.1 Wiring Diagram:

Output V+ is common anode for RGBW LED

Receiver

LE D

PR I :

Uin=1 2- 36 V D C

Iin =2 0. 5A

SE C :

Uou t= 4x (1 2- 36 )VD C

Iou t= 4x 5A

Pou t= 4x (6 0- 18 0) W

LED C O N T R O L LER

H-R009 PD

Lea rn ing K ey

Rep eater S ignal

Class 2 Regulated

Power Supply

12-24VDC

110V-230VAC

Receiver Repeater

RGB/W LED Strip

RF remote H-2819S

(Optional)

[V+]

[V-]

[W]

[B]

[G]

[R]

[+]

V+

V-

V+

Power Input

RGBW Output

Make sure that

wires cannot

cross

Make sure that

wires are fully inserted

wrong correct

Note: Verify with a pull on the wire to test if wire is securely connected

Receiver 1 is connected wirelessly with RF remote

Receiver 2 is in slave mode connected by wire

Receiver 3 is in slave mode connected by wire

Note: Jumper should be

in receiver mode

(default is receiver mode)

Note: Jumper is in receiver mode

Note:

Jumper

is in repeater

mode

Securely mount with

screw to surface

AC Power

50/60Hz

V+

V-

Class 2 Regulated Driver

(12~24VDC)

AC Power

50/60Hz

V+

V-

Class 2 Regulated Driver

(12~24VDC)

(Red Wire)

(Black Wire)

(Red Wire)

(Black Wire)

(Red Wire)

(Black Wire)

D1+

Signal Out

D1-

D2+

D2-

Signal In

HUEDA™ RF Receiver/Controller

Use this method if the distance of the controller (ex. hand remote) is farther than 75 ft to the RF Color Receiver (H-R009PD)

Wire Color may vary, usually Black wire

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 03/03/16

RGB/W LED Fixture

Power Input

Model: H-R009PD 1-800-387-4081

ledworldlighting.com ledworld.ca |

4/4 Copyright © 2016 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

Federal Communications Commission (FCC) Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

Note: The manufactures is not responsible for any radio or tv interference caused by unauthorized

modications to this equipment. Such modications will void the user's authority to operate the

equipment and warranty.

THREE YEAR LIMITED LIGHTING WARRANTY

LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other

warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective.

This Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and

claims must be submitted to them. Use only with LED World’s regulated class 2 power supply.

LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from,

connected with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill,

anticipated or otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault

or wrongdoing (including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has

been advised of the possibility of such loss or damage being incurred.

If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return

authorization number.

HUEDA™ RF Receiver/Controller

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.2 03/03/16

HUEDA™

(LW-2814DMX)

HUEDA™ Hub

(H-2818WIN)

5CH DMX Decoder

(H-DMX2108A-5M-3)

RF RGBW Receiver

(Outdoor)

(H-R009FA(W))