LED World HUEDA Assembly instructions

1/7
ŸSecurely mount the Hueda Controller
ŸThis product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance
with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage
Class 2 power supply (12-24V DC Max). Failure to use a Class 2 power supply may cause re or serious injury
and will void the limited warranty.
ŸEnsure applicable wire is installed between driver, xture and any controls in between. When choosing wire,
factor in voltage drop, amperage rating and type (in-wall rated, Plenum rated, wet location rated, etc.).
Inadequate wire installation could overheat wires and cause re.
ŸThis product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near
water (or the possibility of in the future).
ŸDo not modify this product beyond the instructions in this guide or the limited warranty will be voided.
ŸWiring diagrams in this installation guide for basic installations. Please carefully review your installation before
proceeding with a qualied electrician familiar with low voltage wiring.
ŸNever install the HUEDA™ Controller in with other high voltage Junction Box as there is a risk of shock hazzard!
National Electric Code requires electrical conductors to be separated by a barrier within the box or in a
separate box!. Install only in the provide Junction box.
IMPORTANT NOTE
Install Hueda DMX controller in a separate box rated for Low voltage use. NEC codes requires conductors shall not be
placed in any raceway, compartment, outlet box, junction box, or similar tting with conductors of electric light or power.
Safety & Warnings
Before you begin, read all warnings and installation instructions.
Wire Ends:
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure
all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 24 to 18 AWG
gauge wire for output terminals.
WIRE 6-8MM (0.25-0.30”)
Included Items in Box
ŸCAT5 Wire
ŸMounting Junction Box
ŸInstructions
INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
2/7
Zone Control
Dynamic Modes
RGBW Control
Color Wheel
Scroll through to nd specic color.
Power
Press to turn ON/OFF device
H
zones
U E D A
12 3
TM
Three Choices of White
Brightness Control
Press to select/deselect zones 1-3
Operation Overview
Press to turn ON/OFF Red,
Green,Blue and White color
Long press to adjust brightness
of individual color
Long press to increase/decrease
brightness
Press to cycle through the choices of white
Long press adjusts speed of dynamic
color changing mode.
Install in accordance with the NEC and local regulations.
Installation Overview
ŸTurn power OFF at main circuit breaker and verify the power is off.
ŸDetermine an accessible location for a compatible low voltage driver to be installed between the main
breaker and DMX controller. Determine a location to install additional accessories such as DMX decoders,
xtures etc. Ensure applicable wire is installed between all components. When choosing wire, factor in
voltage drop, amp rating and type to prevent re or electric shock.
ŸRemove the existing wall plate and switch. Pull switch from identify wires and disconnect from switch.
ŸRemove existing switch box from wall and install the included DMX controller switch box. Additional tools
may be required to t DMX controller switch box in the wall.
ŸMake wiring connections. See ‘Wiring Connections’ and ‘Mounting Diagram’ for additional information.
ŸReplace wiring back into switch box. Mount and align DMX decoders/xtures. See ‘Setting the DMX
Address’.
Remote Operation
ŸThe DMX controller can also be con also be controlled remotely via wi- with a compatible
ios/Android tablet or mobile device using our application “HUEDA”.
ŸPlease see our HUEDA™ web page for application instructions.
http://www.ledworldlighting.com/product/dmx-color-controllers/hueda-led-controller/
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15

3/7
MountingWiring Connections
DO NOT connect directly to 120VAC.
See ‘System Diagram for a general system design.
Pop off faceplate with a athead screwdriver
Install with the included DMX controller wall box.
GND Data + Data -
Vin GND
Reset
Switch
1 2 3
From 12-24V
To DMX Decoder
or DMX xture
Setting the DMX Address
Zone 1: Set to address ‘001’ (will be xed to address 001 – 004)
1 2 3 4 5 6 78 9 10
ONDIP
001 002 004 008 016 032 064 128 256
FUN
ON
OFF
Zone 2: Set to address ‘005’ (will be xed to address 005 – 008)
1 2 3 4 5 6 78 9 10
ONDIP
001 002 004 008 016 032 064 128 256
FUN
ON
OFF
Zone 3: Set to address ‘009’ (will be xed to address 009 – 012)
1 2 3 4 5 6 78 9 10
ONDIP
001 002 004 008 016 032 064 128 256
FUN
ON
OFF
Each DMX decoder or DMX xture need to be addressed correctly so the controller can distinguish between
each one. To pair a DMX decoder or xture to a specic zone of the controller (1-3), set each decoder/xture
to one of the following addresses
Each zone of the controller is xed with 4 DMX
addresses to control the 4 channels:
Ch1 – Red, CH2 – Green, CH3 – Blue, CH4 – White or X
INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
WARNING!!! Never install the HUEDA™ Controller in with other high voltage Junction Box as there is a risk of shock
hazzard! National Electric Code requires electrical conductors to be separated by a barrier within the box or in a
separate box!. Install only in the provide Junction box
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15

4/7
Pinout Connection Guide
RJ45 568B Connection Pinout
1
RJ45 568B Pinout Table
Pin No. Wire Color Function
1 White/Orange Data +
2 Orange Data -
3 White/Green None
4 Blue None
5 White/Blue None
6 Green None
7 White/Brown May be used as 2nd ground
8 Brown Ground
Pin No. Function
1 Ground
2 Data -
3 Data +
XLR-3 Connection Pinout
2 3 4 5 6 7 8
XLR-3 Pinout Table
1
2
3
1
2
3
Female Male
The following diagrams/tables indicate the appropriate connections for patching your own CAT5/RJ45, and
XLR-3 splice cables. These diagrams are for general reference and may slightly differ between different cable
manufacturers.
Mode Description
1 Full Color Fade #1
2 Reverse Rainbow Fade
3 Random Full Color Fade
4 7 Color Jump
5 RGB Fade In / Fade Out
6 RGB Fade In to Off
7 RGB On to Fade Out
8 RGB Jump
9 Full Color Fade #2
10 Pastel Color Fade In / Fade Out
Dynamic Mode Chart
The Dyna mic Mode tool pl ays facto ry-
programmed scenes. Choose up to 10 different
scenes. Short press switches/pauses the mode.
Long press adjusts speed of the dynamic mode
Troubleshooting
For thorough troubleshooting of LED strip light and xtures, see LED xture installation guides.
LED xtures not responding to touch
LED xture responding incorrectly
ŸEnsure the blue indicator light is on by pressing ‘Power Button’.
ŸEnsure the appropriate zone number was pressed prior to controlling the DMX decoder/xture. For example, if you
know the xture is addressed to zone 1, press 1 prior to controlling.
ŸEnsure the individual zone has not been turned off. Pressing zones 1-3 will turn the specic zone ON/OFF. Additionally,
long pressing R, G, B, W will increase/decrease individual brightness and tapping will turn R, G, B, W ON/OFF.
ŸEnsure the DMX decoder/xture is addressed properly. For example, address ‘001’ will respond to zone 1 of the
controller.
See ‘Setting the DMX Address’ on page-2 for additional addressing information.
Ensure all wiring connections are correct. Reversing the Data + and Data - will cause lights to icker and not respond to
controller.
ŸPower connections of all components (drivers, DMX decoders/xtures, DMX controller).
ŸDMX Data connections -see ‘Pinout Connection Guide’ and ‘System Diagram’ for Rj45 hard-wiring connections.
ŸDMX decoder PWM output connections -see ‘System Wiring Diagram for CH 1-4 connections
INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15

5/7
System Wiring Diagram
V+
Ch1 Ch2 Ch3 Ch4
Data IN
Data OUT
DMX Data
Output
Power
Input
L
N
AC Power
50/60Hz
Class 2 Low Voltage Driver *
G
N
L
t
u
p
n
I
t
u
p
t
u
O
V+
V-
HUEDA™ Controller
DMX Decoder (LT-840)
RGB Strip Light / Fixture
CH4-W connection: only utilized for white LED strip.
Wall Washer / DMX-512 Fixture
AC Power
50/60Hz
RJ45 / XLR-3
Adapter Connector
RJ45 Splice Cable
Wiring Connections
Brown Ground
White/Orange Data +
Orange Data -
R
G
B
DC+ DC-
V+
Ch1 Ch2 Ch3 Ch4
Data IN
RGB Strip Light / Fixture
R
G
B
DC+ DC-
D- GNDGND D+
SR-2811DMX(US)
Vin
Channel Color
Channel 1 - Red
Channel 2 - Green
Channel 3 - Blue
Channel 4 - White (optional)
* Use a compatible Class 2 constant voltage driver. It is recommended to load the driver no more than 80%.
For additional information and questions please contact our technical support.
AC Power
50/60Hz
G
N
LV+
V-
AC Power
50/60Hz
G
N
LV+
V-
Method 1 :
DMX Decoder (LT-840)
Data OUT
Class 2 Low Voltage Driver *
Class 2 Low Voltage Driver *
The following wiring diagram is as an example system connectivity. CAT5 (RJ45 connections) cables are the most
effective solution for transmitting DMX-512 signals. XLR-3 cables may also be installed but require an additional
adapter for connecting to DMX decoders (LT-840). With DMX decoders like LT-840, it is possible to transmit signal
wireless with use of LC-512X wireless sticks. Always review each component’s installation guide for detailed and up-
to-date wiring instructions. Install in accordance with NEC and local regulations.
Max 500mA
INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
+-
Make sure that
wires cannot
cross
+-
Make sure that
wires are screwed tight
and fully inserted
wrong correct
Warning
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15
D- GNDGND D+Vin
Orange
White/Orange
Brown
VDC
VDC
Power In DMX Data Out
_+

6/7
V+
Ch1 Ch2 Ch3 Ch4
Data IN
Data OUT
DMX Data
Output
Power
Input
Class 2 Low Voltage Driver *
HUEDA™ Controller
RGB Strip Light / Fixture
CH4-W connection: only utilized for white LED Strip.
Wall Washer / DMX-512 Fixture
AC Power
50/60Hz
RJ45 / XLR-3
Adapter Connector
RJ45 Splice Cable
Wiring Connections
Brown Ground
White/Orange Data +
Orange Data -
R
G
B
DC+ DC-
V+
Ch1 Ch2 Ch3 Ch4
Data IN
RGB Strip Light / Fixture
R
G
B
DC+ DC-
D- GNDGND D+
SR-2811DMX(US)
Vin
Channel Color
Channel 1 - Red
Channel 2 - Green
Channel 3 - Blue
Channel 4 - White
* Use a compatible Class 2 constant voltage driver. It is recommended to load the driver no more than 80%.
For additional information and questions please contact our technical support.
AC Power
50/60Hz
G
N
LV+
V-
AC Power
50/60Hz
G
N
LV+
V-
Method 2 :
Class 2 Low Voltage Driver *
White/Green VDC - (GND)
White/Blue VDC + (Vin)
CAT5 ( Rated For Inside Wall use)
DMX IN
Data + Data - Ground
DMX Decoder (LT-840)
DMX Decoder (LT-840)
Data OUT
Class2 Power Input
INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
+-
Make sure that
wires cannot
cross
+-
Make sure that
wires are screwed tight
and fully inserted
wrong correct
Warning
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
VDC+VDC-
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15
D- GNDGND D+Vin
VDC
VDC
Power In DMX Data Out
_+
White/Green
White/Blue
Orange
White/Orange
Brown

INSTALLATION SHEET
HUEDA™-Multi Zone LED Controller INSTALLATION SHEET
HUEDA™-Multi Zone LED Color Controller
7/7
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
ŸThis device may not cause harmful interference, and
ŸThis device must accept any interference received, including interference that may cause undesired
operation.
Note: The manufactures is not responsible for any radio or tv interference caused by unauthorized modications
to this equipment. Such modications could void the user's authority to operate the equipment.
Federal Communications Commission (FCC) Statement
Scan QR code to download HUEDA™ Application
Download
EasyLighting EasyLife App
From
Google Play Store
Download
HUEDA App
From
IOS App Store
Copyright © 2015 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.4 10/19/15