12V
DC Output
LISTED
6
Years
Limited Manufacturer
Warranty
Select a suitable location capable of supporting the weight of the transformer. Use
the four keyholes on the transformer case. Screw cover closed. Mount the unit at a
height greater than 1ft (30cm) from the ground.
ŸThe driver must be installed in a well-ventilated area free from explosives gases and vapors. Proper operation requires for free ow of air. Do not install
inside a cabinet smaller than 12 W x 12 H x 15 L inches. If you are installing multiple drivers, keep a minimum space of 5" (127mm) between each driver.
For Indoor or Outdoor use.
ŸOperate only within specied ambient temperature range of 4°F (-20°C) to 104°F (40°C). Operating at cooler surrounding air temperature will extend driver life.
ŸAll wiring must be in accordance with NEC/CEC, low voltage Class 2 circuit. For wire runs inside of walls, use properly certied CL2 or better cabling and
appropriate mounting hardware. If you are unclear as to how to install and wire this product, contact a qualied licensed electrician. Failure to install this device
properly may result in electrical shock or re.
ŸDo not overload. Total wattage of all LED xtures used must not exceed the 180 watt rating of this power supply. Maximum of 48 watt in each output for continuous
use.
ŸRoute and secure wires so they will not be pinched or damaged.
ŸDo not install Class 2 low voltage wiring in the same run(s) as AC main power.
PRECAUTIONS BEFORE INSTALLING
INSTALLATION GUIDELINES
MOUNTING
INPUT CONNECTIONS / GROUNDING
OUTPUT CONNECTIONS (LOW VOLTAGE)
ŸFor all wire connections use only UL/CSA listed wire nuts or wago connectors of
suitable size and type.
ŸUse 3/8” (1/2” KO) cable connectors (not included) to secure wire.
ŸMaximum of 12AWG through branch circuit conductor suitable for 105°C
(221°F) permitted in box.
ŸRemove the wiring cover (2 screws). Remove the wiring compartment
knockout and install strain reliefs (not included). With power turned off at the
breaker, route the input wires. Connect one wire to black(L) and one wire to
white(N) to the corresponding pigtail wire.
ŸIf used outdoor, must have knockouts point downwards. Use only outdoor rated
UL/CSA listed strain relief (water tight).
ŸThe Driver case MUST be grounded in accordance with the NEC/CEC. Connect
the ground wire to the driver green wire.
Model: MD-012-180VWJ2V2
12VDC 180W Class 2 Constant Voltage LED Driver
1-800-387-4081
ledworldlighting.com ledworld.ca |
5”(127mm) min spacing between drivers
If used outdoors, the knockouts must point downward
Knockouts
Install strain reliefs
(Note: Use water tight strain relief
for outdoor location installation)
Input Output
Black (L)
White (N)
Green (G)
Black (V-)
Red (V+)
3x60
Watts
3x5
Amps
ŸMeasure the output voltage for proper voltage to LED xture.
ŸWARNING - Do not interconnect output terminations. Risk of Fire or Electric
Shock.
ŸConnect the wires of the light xture to the driver wires - positive to the red(+)
wire and negative to black(-) wire.
ŸAfter all wiring completion, screw in wiring cover.
Wiring cover
+ +
ŸOnly qualied personnel should install the unit.
ŸRead all instructions before installation. To be sold with instructions.
ŸCheck the wire markings to ensure they match the wiring diagram on this installation guide.
ŸEnsure the unit has the proper input/output voltage and output wattage for your application.
ŸTurn off power at breaker before starting.
ŸInstallation must comply with the National Electrical Code (Article 450) and Canadian Electrical Code.
Use appropriate UL/CSA listed
wire nuts or wago connectors (not included) to connect wires
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 09/13/23
Copyright © 2023 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
1/2
