Ledj VersiLED 6 Wireless DMX Controller User manual

Order code: LEDJ324
VersiLED 6 Wireless
DMX Controller
User Manual
BLACKOUT STROBE
M1 M4
M2 M5
M3 M6
CHANNEL
MODE
0
100
80
60
40
20
R G W A UV/D
0
100
80
60
40
20
0
100
80
60
40
20
0
100
80
60
40
20
0
100
80
60
40
20
SPEED
30
SEC
0.1
SEC
1-10
1
11-20
2
21-30
3
31-40
4AUTO SOUND
RUN MODE
B
DIMMER/
STROBE
SPEED
SOUND
SENSITIVITY
0
100
80
60
40
20
R G B
RGBW
MIX
AUV
MIX
W A UV
A UVR G B W
MACRO
1
8
7
6
5
4
3
2
M1: RGB
M2: RGBW
M3: RGBWAD
M4: RGBWAUV
M5: RGBWA
M6: RGBWAUVD
VersiLED 6 Wireless
DC INPUT
DC 9V-12V
300mA min
DMX OUTPUT
PAIR
1 = Ground
2 = Data -
3 = Data +
2
1
3
VersiLED 6 Wireless
www.prolight.co.uk
POWER
ON OFF
IO
STATUS

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 100~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Prolight
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This xture is for professional use only - it is not designed
for or suitable for household use. The product must be
installed by a qualied technician in accordance with local
territory regulations. The safety of the installation is the
responsibility of the installer. The xture presents risks of
severe injury or death due to re hazards, electric shock
and falls.
• WARRANTY: One year from date of purchase.

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 3
Product overview & technical specications
The VersiLED 6 Wireless from LEDJ is a universal DMX controller designed for controlling multi colour LED xtures.
Suitable for use with RGB, RGBW/RGBA, RGBWA or RGBWAUV products, with or without dimmer channels the
controller may be used for LED par cans, panels or even LED strip lights. The on-board W-DMX transmitter allows
for wireless DMX control.
VersiLED 6 Wireless DMX Controller
• Can control up to four xtures/groups from RGB through to
RGBWA+UV, each xture may be set individually
• Master dimmer function, even for RGBWA+UV products
• Separate RGBW and Amber/UV colour mix on fader control
• LTP control system for intuitive operation
• Strobe function with adjustable speed (1-20Hz)
• Built-in W-DMX Sweden transmitter for wireless operation
Specications VersiLED 6 Wireless
Power supply DC 9V-12V, 300mA min
(by adaptor included)
Dimensions 60 x 250 x 120mm
Weight 1.1kg
Order code LEDJ324
01 - RGBWAUV/D channel faders
02 - Fixture/group buttons & LED
indicators
03 - Channel mode selection & LED
indicators
04 - Run mode select (auto or sound)
05 - Blackout button
06 - Strobe button
07 - RGBW colour mix
08 - Amber/UV colour mix
09 - Colour macro fader
10 - Speed control
11 - Strobe speed/sound sensitivity/
master dimmer
12 - W-DMX Antenna
13 - W-DMX Status Indicator
14 - W-DMX Pair Button
15 - 3-Pin DMX output
16 - DC power input (centre +ve)
17 - Power on/off switch
In the box:
1 x controller,
1 x power adaptor
& 1 x user manual
BLACKOUT STROBE
M1 M4
M2 M5
M3 M6
CHANNEL
MODE
0
100
80
60
40
20
R G W A UV/D
0
100
80
60
40
20
0
100
80
60
40
20
0
100
80
60
40
20
0
100
80
60
40
20
SPEED
30
SEC
0.1
SEC
1-10
1
11-20
2
21-30
3
31-40
4AUTO SOUND
RUN MODE
B
DIMMER/
STROBE
SPEED
SOUND
SENSITIVITY
0
100
80
60
40
20
R G B
RGBW
MIX
AUV
MIX
W A UV
A UVR G B W
MACRO
1
8
7
6
5
4
3
2
M1: RGB
M2: RGBW
M3: RGBWAD
M4: RGBWAUV
M5: RGBWA
M6: RGBWAUVD
VersiLED 6 Wireless
DC INPUT
DC 9V-12V
300mA min
DMX OUTPUT
PAIR
1 = Ground
2 = Data -
3 = Data +
2
1
3
VersiLED 6 Wireless
www.prolight.co.uk
POWER
ON OFF
IO
STATUS
01
151413
12
16 17
02
04 05 06
03 07 08 09 10 11

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 4
Initial setup:
Connect the supplied mains power adaptor to the DC power input on the controller and then to a
suitable mains voltage supply (100-240VAC~50/60Hz).
The controller can be used to control 3, 4, 5 or 6 colour LED products each with or without a
dimmer channel.
The controller is based around LTP (Last Takes Precedence) across its control surface, this means the
last command executed on the controller will override the previous command. Because of this, the
controller is easy to use for those who carry little knowledge of DMX controllers.
DMX channel assignment:
The controller has preset DMX start addresses for each of the four xtures. Please set your xture to the
following DMX addresses.
Please note: If two or more xtures are set to the same DMX address they will receive the same
DMX commands.
Master dimmer:
The controller also has an additional Master Dimmer function. While holding down the Blackout
button, use the strobe/dimmer fader to adjust the overall master intensity. This function will operate for
all xtures regardless of xture selection. The master dimmer function will override all outputs including
sound and auto modes. If you have used the master dimmer to dim your xture(s) to zero you will have
to dim them back up in order to use manual dimming/colour mixing again.
01) RGBWAUV/D channel faders:
The RGBWAUV/D faders are used to create a manual colour mix. First select the xture groups
as required from the four xture groups and then use the faders to adjust the colour and intensity
as required.
02) Fixture/group buttons and LED indicators:
The xture/group buttons are used to select or deselect xtures. Next to each button is an LED
indicator, this will illuminate when the xtures are selected.
Please note: the xture/group button will ash to indicate this was the last xture/group to be used.
Operating instructions
Fixture Number Group DMX Start Address
1001
2011
3021
40 31

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 5
03) Channel mode selection and LED indicators:
The controller can be used to control up to four xtures/groups from RGB through to RGBWA+UV,
each xture may be set individually to suit the DMX channels of your LED xtures from RGB up to and
including RGBWAUV+Dimmer. Select the desired xture/group using the xture/group buttons, then
select the channel mode. Unselect the xture/group and then repeat the process for each of the four
xture/groups until set. Please note: When using Mode 6, the dimmer channel output value will be 255,
this enables you to colour mix and then use the master dimmer detailed above.
Fader allocation VS Mode chart:
04) Run mode select (auto or sound):
The built-in colour macro’s may be triggered by either sound control or auto with speed control.
Press the Run Mode button to change between sound or auto control. The LED indicator will
illuminate to show the Run Mode. Use the macro fader to select the macro from 1-8 and then use the
speed and sound sensitivity faders to adjust the auto speed or sound sensitivity.
05) Blackout button:
The blackout control can be used for instant blackout (off) commands of the xtures controlled by the
VersiLED 6 controller. The blackout button is a global command and will control the xtures regardless
of any xture/group selection.
Press and hold the blackout button to enable the Master Dimmer function and at the same time use the
strobe speed/dimmer fader to control overall intensity of the dimmer channels. This will also function as
a global command and will control the xtures regardless of any xture/group selection.
06) Stobe button:
Press and hold the Strobe button to activate a white strobe across the xtures selected on the xture/
group. While holding the button, the strobe speed can be adjusted using the strobe speed/sound
sensitivity/dimmer fader. The strobe speed is adjustable 1Hz-20Hz. Please note: If the master dimmer
function has been set to zero then the strobe will not operate. Please set the master dimmer back up for
the strobe to function again.
07) RGBW colour mix:
The RGBW colour mix fader can be used for rapid selection of static colours. Push the fader to fade from
Red, through Green and Blue up to full on at the upper limit of the fader.
Operating instructions
Mode Fader 1 Fader 2 Fader 3 Fader 4 Fader 5 Fader 6 DMX Allocation
M1 RGB Red Green Blue - - - RGB
M2 RGBW Red Green Blue White - - RGBW
M3 RGBWAD Red Green Blue White Amber Dimmer RGBWA + CH6 Master Dimmer
M4 RGBWAUV Red Green Blue White Amber UV RGBWAUV
M5 RGBWA Red Green Blue White Amber - RGBWA
M6 RGBWAUVD Red Green Blue White Amber UV RGBWAUV + CH7 (xed at 255)

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 6
Operating instructions
08) Amber/UV colour mix:
The Amber/Ultra Violet colour mix fader can be used for rapid selection of static colours. Push the fader
to fade from Amber through to Ultra Violet up to full on at the upper limit of the fader. The fader may be
used in conjunction with the RGBW colour mix to add Amber or Ultra Violet into the RGBW mixed colours.
09) Colour macro fader:
The VersiLED 6 controller has built in RGBWAUV colour macro’s that can be triggered by sound with
adjustable sensitivity or auto with speed control. Select the desired xture/groups and then use the
macro fader to select from one of the eight internal colour macros. The auto speed can be set using
the speed fader, while the sound sensitivity can be set using the strobe speed/sound sensitivity/master
dimmer fader.
10) Speed control:
The speed control fader is used to adjust the speed of the built in colour macros.
11) Strobe speed/sound sensitivity/master dimmer:
The strobe speed/sound sensitivity/master dimmer fader provides control for multiple functions
on the controller.
12) W-DMX antenna:
Transmits the W-DMX Signal.
13) W-DMX mode indicator:
When this LED is illuminated red it indicates that the controller is paired with xtures.
When this LED is not illuminated it indicates that the controller is not paired with xtures.
Macro Channel Value Description
N/A 000-007 Blackout
1 008-038 RGB Change
2 039-069 RGB Fade
3 070-100 RGBW Change (RGB used as white)
4 101-131 RGBW Fade (RGB used as white)
5 132-162 Red/Green Change
6 163-193 Red/Blue Change
7 194-224 Green/Blue Change
8 225-255 10 Colour Change (Uses RGB only)

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 7
Operating instructions
14) W-DMX status indicator:
15) W-DMX Pair Button:
To pair the controller with receiving xtures press and hold the “PAIR” button for 2 seconds,
the controller will now pair with all unlinked receivers in range.
To unlink the controller with receiving xtures press and hold the “PAIR” button for 3 seconds,
the controller will now unlink with all linked receivers.
16) 3-Pin DMX output:
DMX output connection. 3-pin XLR output socket. Pin 1 = Ground, Pin 2 = data –ve, Pin 3 = data +ve
17) DC power input (centre +ve):
Centre positive type connection. 9-12VDC, 300mA minimum regulated type.
18) Power on/off switch:
Use this switch to power the controller on/off.
On 900ms, off 100ms - the controller is linked to a transmitter, however there is no DMX signal
Continuously On - the controller is linked to the receivers, DMX signal is being transmitted
On 100ms, off 100ms - the controller is trying to establish a connection/connection has been lost
On 500ms, off 500ms - the controller is unlinking all receivers

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 8
DMX setup
Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.
Please quote: CABL10 – 2m CABL11 – 5m CABL12 – 10m3-Pin:
CABL185 – 2m CABL187 – 5m CABL188 – 10m5-Pin:
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”
from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104,
105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in
the chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.
DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”
XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest
cable path possible. The order in which xtures are connected in a DMX line does not inuence the
DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a
DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,
no matter where it is located in the DMX chain.
DATA cable (DMX cable) requirements (for DMX operation):
This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output, please check
the xtures specications as to which your unit accepts.
Also remember that DMX cable must be daisy chained and cannot be split.

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 9
Notice:
Be sure to follow the diagrams below when making your own cables.
Do not connect the cables shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLRs
outer casing. Grounding the shield could cause a short circuit
and erratic behaviour.
Line termination:
When longer runs of cable are used,
you may need to use a terminator on
the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90,
5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
Termination reduces signal
transmission problems and
interference. It is always
advisable to connect a DMX
terminal, (resistance 120
Ohm 1/4W) between pin 2
(DMX-) and pin 3 (DMX+) of
the last xture.
5-Pin
1
2 4
5
3
3-Pin
1 2
3
Pin Conguration
3-Pin 5-Pin
Pin 1 - Ground
Pin 2 - Negative
Pin 3 - Positive
– Pin 4 - N/C
– Pin 5 - N/C
1
2
3
1
2
3
DMX 512
3-Pin XLR output
DMX 512
3-Pin XLR input
GROUND
DMX +
DMX –
DMX 512
5-Pin XLR output
DMX 512
5-Pin XLR input
1
2
45
3
12
4
5
3
GROUND
N/C
DMX –
N/C DMX +
1 ground
3 hot
2 cold
3-Pin XLR male 3-Pin XLR female
2 cold
3 hot
1 ground
2 cold
1 ground 5 N/C
3 hot 4 N/C
5-Pin XLR male 5-Pin XLR female
4 N/C
5 N/C 1 ground
3 hot 2 cold

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 10
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.

www.prolight.co.uk VersiLED 6 Wireless DMX Controller User Manual 11

www.prolight.co.uk 12 VersiLED 6 Wireless DMX Controller User Manual