Ledvance LMS User manual

LEDVANCE LMS
Sensor Value Microwave
MS-SV-MIC-CS-360-230V-IP20
WARNING:
NOT FOR PRINT
PRODUCTION!
This PDF file is for reference only and not to
be used for the creation of production art.
Colour printouts and screen displays should
not be used for colour approval as colours
may vary from device to device. The colour
values for this file are defined in either
Pantone (PMS), HKS, or in process colours
(CMYK).
For obtaining hard-copies in actual size (1:1)
you need to enter the proper settings in your
printer options.
㮍⥠⋀⢏⠐⛛䤢⍗
弜⣩
㦻3')㠖㖰⅔⇫⃉♑䏶㠖ↅ᧨ ₜ厌⺕㦻㠖㫲䞷
ℝ◿Ⓠ䞮ℶ㒥劔Ⓟ⇫嚁㨦ᇭ
㦻㠖㫲䤓ㇸ唁㓢◿䓗㦻㒥␅⦷䟄厠⻞ヤ₼㣍䯉
䤓唁ㇸ᧨ₜ♾䞷ℝ㦏兗䤓唁ㇸ♑䏶ᇭ⥯⃉䫻ↅ
㒥幍⮖䤓ぽ㆑᧨♾厌抯㒟唁ㇸ䤓⋞ぽᇭ㦏兗㷲
㆞䤓唁ㇸ庆挄䏶䟀唁㨎◰䓖306᧨
+.6㒥劔&0<.槡儱煓煠`㓏⸩󱁹䤓唁ㇸᇭ
啴㦻㠖㖰䤓㓢◿ↅ尐噆♥ 䤓☮ⱚ⻉⺇᧨權
⦷㓢◿折欈₼⇫⒉䦇ㄣ䤓幍函ᇭ
11080857 MS-SV-MIC-CS-360-230V-IP20 UI LEDV v2.indd 1 4/9/2019 4:54 PM

LEDVANCE LMS Sensor Value Microwave
black
score dimension 148 x 210 mm
2
Installation Guide and product diagram
How to Install:
a. Switch off the power.
b. Fix the bottom on the selected position with the inflated screw through the screw holes at the side of the sensor.
c. Connecting the power and the load to sensor according to the wire connection diagram.
d. Switch on the power and test it according to the testing guide.
Wire Connection diagram:
(See the right figure)
a. Connect N, L with power;
b. Connect A, N with load
Product Features:
a. Microwave motion sensor with integrated photocell sensing function can help to save power consumption via
turn on and turn off the power according to its setting; It detects human motion within its detection range.
b. Selectable time delay period from 10 seconds to 15 minutes via knob switch;
c. Selectable daylight sensing level from 10 lux to 2000 lux via knob switch.
d. The sensor can detect the signal passing through the door, glass or thin walls which are not made of metal
material;
Product Specification:
a. Microwave: High-Frequency 5.8GHz CW radar, ISM band
b. Power Input: 220-240V/AC
c. Input Frequency: 50/60Hz
d. Detection Range: 360°
e. Installing Height: 1.5~4m
f. Ambient Light (Selectable): <10-2000LUX
g. Time-Delay (Selectable):
• Min.:10sec±3sec;
• Max.: 15min±3min;
h. Nominal Power Consumption: 0.9W
i. Transmission Power: <10mW
j. Maximum Rated Load:
• 2000W (incandescent lamp)
• 1000W (energy-saving / led-lamp)
k. Detection Motion Speed: 0.6~1.5m/s
l. Detection Distance (selectable): 8m (radius)
Selectable Functions via Knob:
a. Selectable daylight luminance level: Sensing luminance level can work both in the daytime and at night when
you select the “sun” position (max) via knob. It can work in the environment when the luminance less than
10LUX when it is adjusted on the “moon” position (min). As for the adjustment pattern, please refer to the testing
pattern.
b. Time-Delay is added continually: When sensor receives the second induction signal after the first induction, it
will perform the time delay period again according to the 2nd induction.
c. Selective time delay period length: It can be set according to the consumer’s desire. The minimum delay period
is 10sec±3sec. The maximum delay period is 15min±3min.
Note: The high-frequency output of this sensor is only <10Mw- which
is just one 100th of the transmission power of a mobile phone
or the output of a microwave oven.
11080857 MS-SV-MIC-CS-360-230V-IP20 UI LEDV v2.indd 2 4/9/2019 4:54 PM

LEDVANCE LMS Sensor Value Microwave
3
black
score dimension 148 x 210 mm
The wires come in and out from the bottom
The wires come in and out from the side
Installation Guide and product diagram
How to Install:
a. Switch off the power.
b. Fix the bottom on the selected position with the inflated screw through the screw holes at the side of the sensor.
c. Connecting the power and the load to sensor according to the wire connection diagram.
d. Switch on the power and test it according to the testing guide.
Wire Connection diagram:
(See the right figure)
a. Connect N, L with power;
b. Connect A, N with load
Product Features:
a. Microwave motion sensor with integrated photocell sensing function can help to save power consumption via
turn on and turn off the power according to its setting; It detects human motion within its detection range.
b. Selectable time delay period from 10 seconds to 15 minutes via knob switch;
c. Selectable daylight sensing level from 10 lux to 2000 lux via knob switch.
d. The sensor can detect the signal passing through the door, glass or thin walls which are not made of metal
material;
Product Specification:
a. Microwave: High-Frequency 5.8GHz CW radar, ISM band
b. Power Input: 220-240V/AC
c. Input Frequency: 50/60Hz
d. Detection Range: 360°
e. Installing Height: 1.5~4m
f. Ambient Light (Selectable): <10-2000LUX
g. Time-Delay (Selectable):
• Min.:10sec±3sec;
• Max.: 15min±3min;
h. Nominal Power Consumption: 0.9W
i. Transmission Power: <10mW
j. Maximum Rated Load:
• 2000W (incandescent lamp)
• 1000W (energy-saving / led-lamp)
k. Detection Motion Speed: 0.6~1.5m/s
l. Detection Distance (selectable): 8m (radius)
Selectable Functions via Knob:
a. Selectable daylight luminance level: Sensing luminance level can work both in the daytime and at night when
you select the “sun” position (max) via knob. It can work in the environment when the luminance less than
10LUX when it is adjusted on the “moon” position (min). As for the adjustment pattern, please refer to the testing
pattern.
b. Time-Delay is added continually: When sensor receives the second induction signal after the first induction, it
will perform the time delay period again according to the 2nd induction.
c. Selective time delay period length: It can be set according to the consumer’s desire. The minimum delay period
is 10sec±3sec. The maximum delay period is 15min±3min.
Note: The high-frequency output of this sensor is only <10Mw- which
is just one 100th of the transmission power of a mobile phone
or the output of a microwave oven.
Testing Before Using:
a. Turn the TIME knob anti-clockwise to the minimum (10s) and turn the LUX knob clockwise to the maximum
(sun).
b. When you switch on the power, the light will be on at once and 10sec±3sec later the light will be off automati-
cally. Then if the sensor receives induction signal again, it can work normally.
c. When the sensor receives the second induction signals within the first induction, it will restart to time from that
moment.
d. Turn LUX knob anti-clockwise to the minimum (-). If the ambient light is less than 10LUX (darkest), the inductor
load could work when it receives induction signal.
Note: When testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp could not
work! If the load is >60W, the distance between lamp and sensor should be longer than 60cm.
11080857 MS-SV-MIC-CS-360-230V-IP20 UI LEDV v2.indd 3 4/9/2019 4:54 PM

C10449058
G11080857
2019-09-04
Warnings:
a. The product should be installed by licensed electricians.
b. The product should not be installed on any moving objects or surface.
c. Please do not put any obstacles or unrest objects in front of the detection window to influence the detection.
d. Please do not put the sensor near the area which is having tremendous changes of temperature such as air
conditioner or central heater.
e. Please don’t open the case after installation.
f. In order to avoid the unexpected damage of product, please add a 6A safety insurance device whilst installing
the sensor such as fuse or safe tube.
Basic Malfunctions Detection and Troubleshooting
a. If the load cannot work:
a) Check the power and the load.
b) Whether the indicator light is turned on after sensing or not? If yes, please check the load.
c) If the indicator light does not turn on after sensing, please check if the working light corresponds to the
ambient light.
d) Please check if the working voltage corresponds to the power source.
b. The sensitivity is poor:
a) Please check if in front of the detection window there are any obstacles that disturb the signals receiving.
b) Please check the ambient temperature.
c) Please check if the signals source is in the detection fields.
d) Please check if the installation height is within the indicated height level.
c. The sensor can’t turn off the load automatically:
a) If there are continual signals in the detection fields.
b) If the time delay is set to the longest.
c) If the power input is following the instruction.
d) If the environment temperature changes a lot due to its installation location is very close to air conditioners or
central heater.
www.ledvance.com.au
 LEDVANCE Pty Ltd
ABN 34 050 103 181
Suite 2.1A
394 Lane Cove Road
Macquarie Park NSW 2113,
Australia
Ph [phone] / 1300 467 726
www.ledvance.com.au
11080857 MS-SV-MIC-CS-360-230V-IP20 UI LEDV v2.indd 4 4/9/2019 4:54 PM