LEDVANCE LMS Sensor Value Infrared
3
black
score dimension 148 x 210 mm
How to Install:
a. Switch off the power.
b. Loosen the screw in the back and unload the bottom (refer to figure 1).
c. Find the wire hole in the bottom and pass the power wire through hole. Connect the power wire into connection-
wire column according to the connection-wire diagram.
d. Fix the bottom with inflated screw on the selected position. (refer to figure 2)
e. Install back the sensor on the bottom, tighten the screw and then test it.
f. After finishing installing, turn on the power and then test it.
Wire Connection diagram:
(See the right figure)
Testing Before Using:
a. Turn the TIME knob anti-clockwise to the minimum (-). Turn the LUX knob clockwise to the maximum (sun).
b. Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After warm-up
30sec, the sensor can start work. If the sensor receives the induction signal, the lamp will turn on. When no
induction signal is received within 10sec±3sec, the load should stop working and the lamp would turn off.
c. Turn LUX knob anti-clockwise on the minimum (moon). If luminance level is more than 10LUX, the sensor would
not work, and the lamps stop working. If the ambient light is less than 10LUX (darkness), the sensor would work.
Under no induction signal condition, the sensor should stop working within 10sec±3sec.
Note: When testing in daylight, please turn LUX knob to (SUN)
position, otherwise the sensor lamp could not work! If the load is
>60W, the distance between lamp and sensor should be longer
than 60cm.
Product Features:
a. Infrared motion sensor with integrated photocell sensing function can help to save power consumption via turn
on and turn off the power according to its setting; It detects human motion within its detection range.
b. Infrared motion sensor cannot receive the induction if there is glass, wood or metal materials in between within
detection range;
c. Selectable time delay period from 10 seconds to 7 minutes via knob switch;
d. Selectable daylight sensing level from 10 lux to 2000 lux via knob switch.
Product Specification:
a. a. Detection method: Infrared motion sensor with photocell integrated
b. Working temperature: -20~+40°C
c. Power Input: 220-240V/AC
d. Input Frequency: 50/60Hz
e. Detection Range: 180°
f. Installing Height: 1.8~2.5m
g. Ambient Light (Selectable): <10-2000LUX
h. Time-Delay (Selectable):
• Min.:10sec±3sec;
• Max.:7min±2min;
i. Nominal Power Consumption: 0.5W
j. Transmission Power: <10mW
k. Maximum Rated Load:
• 1200W (incandescent lamp)
• 300W (energy-saving / led-lamp)
l. Detection Motion Speed: 0.6~1.5m/s
m. Detection Distance (selectable): 8m max. (<24°C)
Selectable Functions via Knob:
a. a. Selectable daylight luminance level: Sensing luminance level can work both in the daytime and at night when
you select the “sun” position (max) via knob. It can work in the environment that the luminance is less than
10LUX when it is adjusted to the “moon” position (min). As for the adjustment pattern, please refer to the testing
pattern.
b. Time-Delay is added continually: When sensor receives the second induction signal after the first induction, it
will perform the time delay period again according to the 2nd induction.
c. Selective time delay period length: It can be set according to the consumer’s desire. The minimum delay period
is 10sec±3sec. The maximum delay period is 15min±3min.
Installation Guide and product diagram
INSTALLATION ADVICE:
As the detector responds to changes of temperature, please avoid the following situations:
a. Avoid directing the detector towards objects with highly reflective surfaces, such as mirrors etc.
b. Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light etc.
c. Avoid directing the detector towards objects that may move in the wind, such as curtains, tall plants etc.
11080851 MS-SV-INF-WS-AD-180-230V-IP44-A UI LEDV v2.indd 3 4/9/2019 4:52 PM
