LEDX Snock 2000 User manual

Congratulations on your choice of LEDX Lights headlamp
You have chosen a quality product developed and manufactured in Sweden for
tough conditions. By using components of highest quality and giving you access to
our excellent service, we create long-lasting products thus reducing the
environmental impact. Please contact LEDX Lights service department for
maintenance and repair if you are experiencing any problems with Your product.
Safety regulations
Warning!
The light from the lamp is very powerful, avoid looking directly into the lamp or aiming
into your own or somebody else’s eyes. Close your eyes and move your head away from
the light beam if someone accidentally directs the light into your eyes. Don´t use
binoculars or any other powerful focusing optics to look at the light beam.
Don´t try to repair the lamp or the battery yourself, if for any reason it is not working.
Trying to open the battery yourself is associated with the risk of fire or explosion. Contact
LEDX Lights service for guidance in case you are experiencing any problems with your
product.
Heat dissipation:
The lamp can get very hot, appr. +70°C. If the lamp is used without adequate airflow,
outdoors or indoors, in a couple of minutes lamp effect will be gradually reduced to appr.
75%, or 1600 lumens. The lamp needs constant airflow through the cooling fins achieved
by movement to deliver full effect. The speed depends on the surrounding temperature,
but 6 km/h is considered to be a target value at +20°C.
The lamp has a built-in thermostat preventing the lamp from overheating. It automatically
reduces the effect if the temperature exceeds +70°C, the effect gradually increases when
the temperature goes down again.
Technology

Even the light beam gets very hot. The light from the lamp is very concentrated and can
reach the temperatures over +100°C close to the lamp. Don’t cover the lamp (for ex. put
it in a pocket or a bag) when the light is on, avoid aiming at the flammable objects when
near them. This could cause a fire or other damage.
NB:
Always disconnect the battery when the lamp isn’t in use, for example for transportation
or storage. This is to avoid the lamp turning on by accident and slowly draining the
battery. The lamp uses some energy if connected to the battery even when it is off,
though this energy usage is very low. There is a risk that the lamp can drain the battery
and destroy or seriously damage it.
Water resistance:
The lamp and the battery are weathertight and can withstand all weather conditions and
water splashes, but it shouldn’t be used under the water or washed with a high-pressure
cleaner. Meets IP65.
The lamp
Turn the lamp on
Connect the battery to the lamp, turn the lamp on by holding the switch-on button
(appr. 1 sec). Switch between effect modes by clicking the button, turn the lamp off
by holding the button. The lamp is in programme 5 with 3 effect modes and starts
with the lowest effect when delivered. Later the lamp starts in the effect mode which
was used when the lamp was switched off. If the battery is disconnected the lamp
will start at the low effect the next time it is switched on.
The lamp can easily be tilted up or down, it could feel a bit stiff when the lamp is new.
Usually, it is best to aim the lamp so the light goes straight forward, thus the lens and the
reflector distribute the light and you get the right amount of it where you need it.
Burning time
The table below shows the approximate burning times with the standard battery. The
lamp can be complemented with the LEDX Lights batteries with higher capacity if
longer burning times are desired. (Available from Feb 2022).
Programmed modes and power usage as well as burn time for different modes apply to
fully a charged battery and at appr. 20°C.

Programming
The lamp can be programmed to adjust to your own preferences:
The lamp can be programmed to adjust to your own preferences: click the switch
button 4 times quickly to activate the programming mode –the lamp shines. Click once
at a time and the lamp will answer by blinking, showing which mode you are in –for
example 3 clicks with the blinking sign in between them, the lamp will blink 3 times.
When you’ve chosen the mode, hold the button in to turn the lamp off. You are now in
your chosen mode, test to check it is the correct mode.
Reserve light
When there is just little energy left, the lamp gradually drops down to low effect and
shines for extra 60 min with 400 lm and thereafter for 30 min with 100 lm. It is even
possible to go directly to 100 lm and thus get extra burning time of 2h and 30 min.
1 h 30 min 400 lumens 60 min, 100 lumens 30 min
Programmed mode
Mode
Effect
5%
Effect
20%
Effect
40%
Effect
75%
Effect
100%
Blinks
1
1
x
1
2
2
x
x
x
2
3
3
x
x
3
4
4
x
x
x
x
x
4
5 (preselected)
5
x
x
x
5
Effect usage in watts
1
3,5
8
15
20
Light output in lumens
100
400
950
1600
2000
Burning time at 20°C
48
9 h
4 h
2 h
1 h 30
min

2 h 30 min 100 lumens
Battery
Li-Ion-battery with USB-C-charging, battery indicator and back light.
The battery needs to be charged before use, connect the included USB-C cable to your
phone charger, your computer’s USB-A port or equivalent, connect USB-C end to your
battery. Depending on the charger’s capacity the charging takes 4 –8 hours if the battery
is empty. Don’t charge the battery at temperatures lower than +2°C.
Don’t store the low charged battery, if there is 20 - 40 % capacity left (1LED visible)
you should charge it within a week, if there is less than 20% left (1LED blinking) You
should charge it within a couple of days to avoid damage. For long-time storage (a
few months or longer) charge the battery to 40-60% and store it in a dry, preferably
cool place, not warmer than normal room’s temperature. Check the charging status
every three months and charge it if needed.
The battery effect reduces with low temperatures, avoid using the battery if it’s
temperature is lower than -20°C. Li-Ion batteries have long life time and can be charged
multiple times, however the battery’s capacity and burning time with it will be reduced
with time.
Reset the battery
Test resetting the battery by connecting the USB-C cable and charging the battery for a
couple of seconds if LED-indicator can’t be activated.
Battery indicator
Charging status is indicated by blinking LEDs
turned on gradually; all 5 LEDs are constantly
on when the battery is fully charged.
The same LEDs show the rest capacity left in
the battery when not connected to the charger.
Click on the marked touch-button on the
battery to activate the LED-panel.
Red backlight
By holding the touch-button You can
activate the strobing backlight from the
LEDs on
Capacity %
appr.
5
95-100%
4
80-95%
3
60-80%
2
40-60%
1
20-40%
1 blinking
1-20%

LED 1, 3 and 5. One short click in this mode will give You a constant light. Turn the
backlight off by holding the button in.
Click mounting
The lamp and the battery can be easily moved between the headgear and different
mountings in the LEDX Lights systems thanks to the new LEDX Lights LX-mount.
LEDX Lights systems
The lamp and the battery are the heart in LEDX Lights big systems ofdifferent lamps,
batteries and accessories. Most of them are compatible with each other. LEDX
Lights offers a wide range of accessories for the lamp to give you the opportunity to
combine the best accessories with your unique needs. The lamp and the battery can
be mounted on basically any type of helmets, there are mountings for firearms
(compatible with Weaver and Picatinny), bike handlebars, etc. Extension cables,
cables for connection to external 12V DC, etc. Check the attached accessory guide
or visit https://ledx.se for the latest updates on the accessories.
Specification:
LED 2pcs LED Cree
Lighting system X-pand
Mounting system LX-mount
Connections LX-connector

Size Weight
Lamp 66x52x29mm 71 g
Battery Li Ion
37Wh max/min, 1h30min - 48 h 88x50x36mm 200 g
Lamp with the headgear 125 g
Lamp with the headgear and battery 325 g
Power consumption max appr. 20 W
IP-class IP65
Warranty
3 year warranty against manufacturing defects on Snok 2000 as well as all the other
parts in the system except the battery where the following applies.
3 year warranty against manufacturing defects on the battery but with the deduction
of 1/3 of a new price after one year and 2/3 after 2 years.
Warranty applies only if the lamp is used with LEDX batteries or connected to the
external DC with max 12V using the LEDX Lights protective cables to protect against
temporary over-voltage and short circuit.
This limited warranty applies only to the original customer. LEDX Lights guarantees that
within the period of three (3) years from the purchase date your product is free from defects
in function and materials when used normally. LEDX Lights is responsible to repair or
replace your product under warranty. Please contact your dealer if the lamp shows defects
under warranty time. Attach your proof of purchase when returning the lamp or sending it for
reparation. Returns or repairs within warranty are not possible without the proof of purchase.
This warranty doesn’t apply if the product has been modified or if it has been installed, used,
repaired or maintained in any other way than instructed by LEDX Lights. Warranty doesn’t
apply if the product has been an object of an abnormal physical or electrical use or
negligence, misuse or accident.
Warranty doesn’t cover normal wear. LEDX Lights is not responsible for any direct or
indirect consequences or injuries caused by use of this product. Under no circumstances is
LEDX Lights responsibility greater than the amount you have paid for the product.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the limitations or exclusions above may eventually not apply without
exceptions.
The product You buy from us should be free from defects when you get it. In the unlikely
event your product has any defect, You should notify us within 14 days after receiving the
product.
As a consumer You have a legal right for claims for up to three years from the purchase, but
within reasonable time (two months) from the day the defect was detected.
Contact us on [e-mail] for a quicker service, give us Your full name, attach a copy
of Your order or receipt, a short description of the defect, a picture of the damage if it is
possible as well as Your contact details (address, phone number and e-mail).
Never leave the battery empty or almost empty, make sure to charge it as soon as
possible. An empty battery left for a long period of time is at risk of being damaged
and unable to be charged again.

Kontakt
LEDX of Sweden AB
Göteborgsvägen 10
504 35 Borås
Phone: [phone]
Webbsite: ledx.se
e-mail: [email protected]