Legacy Sconce User manual

2
Registration
3. Owners Record
4. The Cabinetry / Our Commitment
Setup
5. Unpacking Your Speakers
6. Speaker Installation
12. Hook up Cables
13. Amplification
Technology
14. Designer’s Note
15. Specifications

3
The model and serial numbers are located on the rear of the unit. Record
these numbers in the spaces provided below. Refer to them when calling
upon your dealer regarding this product.
Model No. _______________________________
Serial No. _______________________________
Date of purchase: _________________________
Thank you for selecting a Legacy Loudspeaker System. These hand-
crafted instruments will provide you with many years of listening
enjoyment. Please take a few moments to read this brief manual to insure
maximum benefit from your speaker system.

4
Handcrafted
Each Sconce cabinet is impeccably finished with select veneers. The
exquisite finish is hand-rubbed several times to assure a patina at home
with the most elegant decor.
Our Commitment
A great deal of forethought, love and satisfaction is instilled in each piece
of Legacy workmanship. We take pride in getting to know many of our
customers on a first name basis.
Your purchase is backed by the renown “Legacy Satisfaction Guarantee”.

5
Your new speaker system has been very carefully packaged to insure that
it travels to you safely. A double-wall outer carton protects each speaker
with heavy V-board corner protectors. Custom foam end caps are used to
protect the elegant cabinetry, and a plastic liner is provided as
waterproofing. Please save this packing for future transportation. If cartons
become damaged or misplaced, new ones can be purchased from Legacy
Audio.

6
Precautions
If you have any doubts about your ability to properly install in-wall
loudspeakers, you should use the services of a custom installer.

7
Installing the Sconce On-Wall Loudspeakers
Packing List
Sconce Speaker with pre-attached mounting keys
Wall Plate
Installation Manual
Tools Required
Pencil
Level
Phillips Screwdriver
Tape Measure

8
Installation Preparation:
1. Determine and mark the location of all speakers. Use of a level will be helpful to assure
the proper orientation. Sconce speakers may be installed either horizontally or vertically.
Sconce Surround speakers can only be installed in the vertical position. Consider the
location of pipes, wires or other materials that may be affected by drilling or installing
fasteners into the wall.
2. Install suitable speaker wire from your electronic components to the location of where the
speaker terminal plate will rest, once installed, and leave enough wire length to allow easy
connection to both the receiver/amplifier and the speaker. Legacy Audio recommends the
use of up to 16-gauge wire for the Sconce speaker system. If installing in the wall be sure
that the wire meets local electrical code.

9
Mounting Sconce:
1. Install the provided metal wall plate as shown (Figure 1) with a minimum of (4), #8 Pan
Head Screws, making sure that the proper side of the wall plate is placed against the wall.
Note that the Sconce speaker has two pre-attached diamond shaped keys mounted to the
back panel. These keys will align with the corresponding diamond shaped keyholes in the
wall plate.
Consider the position and orientation of the speaker when attached with corresponding key
points. Use screws long enough to provide at least one-inch penetration into the wall stud
or masonry surface. If using the minimum number of mounting screws, insure that at least
one screw is installed on each side of the back plate keyhole area.
It is recommended that on-wall speakers be installed where all fasteners or screws are
imbedded into a wall stud or masonry component. Other options may include the use of
mollies or toggles depending upon the wall materials and thickness.
Caution: Improper mounting of the speaker to the wall could result in the speaker falling,
creating a dangerous condition. You should engage the services of a professional installer
if you are not fully qualified to mount these speakers on a wall.

10
2. Using at least two people, lift the Sconce speaker close to the back plate and make
necessary wire connections insuring correct wire polarity.
3. Place the Sconce speaker onto the back plate aligning the metal keys into the keyhole
areas of the wall plate. Firmly press the speaker down and slide into the wall plate to
secure the speaker.