Legacy Sconce Surround User manual

2
Registration
3. Owners Record
4. The Cabinetry / Our Commitment
Setup
5. Unpacking Your Speakers
6. Speaker Installation
10. Hook up Cables
11. Amplification
Technology
12. Designer’s Note
13. Specifications

3
The model and serial numbers are located on the rear of the unit. Record
these numbers in the spaces provided below. Refer to them when calling
upon your dealer regarding this product.
Model No. _______________________________
Serial No. _______________________________
Date of purchase: _________________________
Thank you for selecting a Legacy Loudspeaker System. These hand-
crafted instruments will provide you with many years of listening
enjoyment. Please take a few moments to read this brief manual to insure
maximum benefit from your speaker system.

4
Handcrafted
Each Sconce cabinet is impeccably finished with select veneers. The
exquisite finish is hand-rubbed several times to assure a patina at home
with the most elegant decor.
Our Commitment
A great deal of forethought, love and satisfaction is instilled in each piece
of Legacy workmanship. We take pride in getting to know many of our
customers on a first name basis.
Your purchase is backed by the renown “Legacy Satisfaction Guarantee”.

5
Your new speaker system has been very carefully packaged to insure that
it travels to you safely. A double-wall outer carton protects each speaker
with heavy V-board corner protectors. Custom foam end caps are used to
protect the elegant cabinetry, and a plastic liner is provided as
waterproofing. Please save this packing for future transportation. If cartons
become damaged or misplaced, new ones can be purchased from Legacy
Audio.

6
Precautions
If you have any doubts about your ability to properly install in-wall
loudspeakers, you should use the services of a custom installer.

7
Installing the Sconce On-Wall Loudspeakers
Packing List
Sconce Speaker with pre-attached mounting keys
Installation Manual
Tools Required
Pencil
Level
Phillips Screwdriver
Tape Measure

8
Installation Recommendations:
1. Determine and mark the location of all speakers since changes to the location of one
speaker may affect the other either aesthetically or acoustically. Sconce speakers may be
installed either horizontally or vertically. Sconce Surround speakers can only be installed in
the vertical position. Consider the location of pipes, wires or other materials that may be
affected by drilling or installing fasteners into the wall.
2. It is recommended that on-wall speakers be installed where all fasteners or screws are
imbedded into a wall stud or masonry component. Other options may include the use of
mollies or toggles depending upon the wall materials and thickness.
3. Install suitable speaker wire from your electronic components to the location of where the
speaker terminal plate will rest once installed and leaving enough wire to allow easy
connection to both the electronic equipment and the speaker. Legacy Audio recommends
the use of up to 16-gauge wire for the Sconce speaker system.

9
4. Install a #10 screw into the wall surface that is long enough to provide at least one inch
penetration into the wall stud or masonry surface and leaving at least 1/8" protruding from
the wall.
5. Using at least two people, lift the Sconce Surround speaker close to the mounting screw
and make necessary wire connections insuring correct wire polarity. Place the Sconce
Surround speaker onto the screw head using the corresponding keyhole on the rear of the
speaker. Insure the speaker locks onto the mount by pushing down.

10
Note: Before you purchase loudspeaker wire, check local building codes
to make sure that the wire is rated to comply with applicable local safety
codes such as UL or CL-2. When pulling wire, take care not to pull the
wire too fast to prevent stretching the wire or damaging the insulation from
friction. Leave 2 to 3 feet of excess loudspeaker wire at both ends; it is
easier to trim off excess wire than to splice additional wire. When securing
the wire inside the walls, be careful not to pierce the insulation with nails
or staples.

11
Ideally the loudspeaker would be among the first components selected when assembling a
playback system. This would allow the user to choose an amplifier capable of delivering
adequate amounts of current into the frequency dependent load presented by the loudspeaker.
However, when upgrading a system, audiophiles may find themselves matching their new
loudspeakers to their existing amplification. For this reason, extensive measures have been
taken to ensure that each Legacy speaker system represents a smooth, non-reactive load to
virtually any amplifier.
How much power will your new speakers need? That ultimately depends on your listening
environment and musical tastes. As little as five watts per channel should drive them to a level
satisfactory for background music. To obtain maximum performance from your Sconce
speakers, 100-150 watts per channel are recommended.
How much is too much power? Rarely is a drive unit damaged by large doses of music power.
More often than not the villain is amplifier-clipping distortion. When an amplifier is unable to
fulfill your loudspeakers demands, a damaging harmonic spike may be leaked to the high
frequency drivers.
Another important point regarding loudness is that the dB scale is a logarithmic one. This
means that a 150-Watt amplifier will potentially sound only twice as loud as a 15 Watt amplifier.

12
Legacy Audio developed two high performance drivers specifically for the
Sconce™ system. Our new 1” Spiral Neo ribbon tweeter provides the ‘air’
and definition found only in the finest audiophile speakers, yet with
dispersion specially optimized for wall placement. The dual 5.25”
midrange/bass driver utilizes our revolutionary new Silver/Graphite cone
material. Silver threads are interwoven with stiff, low mass, graphite fibers
to allow wide bandwidth and high efficiency. A rigid cast frame assures
clarity.
As form and function combine, special filters are included in the crossover to compensate for
the influence that the wall boundary has on the acoustic radiation impedance. Left untreated,
bass will lack definition and vocals will become thick and tubby. Similar to modern bridges, the
curved fronts of the Sconce™ cabinets are braced and tensioned to control vibrations. Wall
mounting is straightforward and sturdy. The uniquely beautiful cabinetry is worthy of the
Legacy hallmark, and is available in a variety of finishes.

13
System Type: 3 drivers, 3 way, bipolar Top firing array
Tweeter: Spiral Ribbon Neodymium Motor
Woofer: 2 x5.25” Cast Frame Silver/Graphite
Frequency Response: 67-22kHz
Impedance: 4 Ohms
Sensitivity: 90 dB
Recommended Amplification: 15-150 Watts
Crossover Frequency: 1.5, 3.2k
Dimensions (H x W x D): 21 x 7 x 7
Weight: 27 pounds

14
Notes:

15
© 2004 Legacy Audio
150 Locust Street.
Macungie, PA 18062
Phone: [phone]
Fax: [phone]