LEGRAND Chief PAC735 User manual

INSTALLATION INSTRUCTIONS
Secure Storage Cabinet
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC735

PAC735 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment!
It is the
installer’s responsibility to make sure the combined weight of all
equipment stored within the PAC735 does not exceed 40 lbs
(18.14 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
--SAVE THESE INSTRUCTIONS--

Installation Instructions PAC735
3
DIMENSIONS
LEGEND
2.35
50.8
2.00
DOOR NOT SHOWN
SUITED TO 10-32 UNF CAGE
NUTS: McMASTER-CARR #
90680A127 OR EQUIVALENT
MAX RACK DEPTH = 20"
DIMENSIONS: [MILLIMETERS]
INCHES
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale

PAC735 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/2" 3/16"
(included)
A (1)
B (1) C (1)
D (1) E (1)
[Front cross bar]
[Storage cabinet]
[Right wedge plate]
[Clamp bracket]
F (1)
[Rear cross bar]
G (4)
5/16-18 x 1"
H (2)
5/16-8 x 1/2"
J (12)
5/16-18"
L (2)
[Key]
[Left wedge plate]
K (2)
1/4"
M (6)
[Bumper] N (1)
3/16"

Installation Instructions PAC735
5
ASSEMBLY AND INSTALLATION
Assemble Base Support (Cart Installation ONLY!)
NOTE: If installing PAC735 to a stand rather than a cart, the
base support is not needed as the PAC735 will sit
directly on the base of the stand. Proceed to Mount
Storage Cabinet section.
1. Place left wedge plate (B) and right wedge plate (C) on a flat
surface with threaded bolts facing up. (See Figure 1)
2. Place front cross bar (E) and rear cross bar (F) on top of
wedge plates and insert bolts through corresponding holes
on cross bars. (See Figure 1)
3. Install eight 5/16-18" hex nuts (J) over each threaded bolt
and tighten until cross bars are secured to wedge plates.
(See Figure 1)
Figure 1
Attach Base Support to Cart
1. Partially install two 5/16-18 x 1/2" square head cap screws
(H) and two 1/4" flat washers (K) into side holes on wedge
plates. DO NOT TIGHTEN! (See Figure 2)
NOTE: Screws should protrude approximately 1/8" beyond
wedge plate edge.
Figure 2
2. Slightly loosen (approximately three turns) the front button
head cap screw on either side of the cart base. (See Figure )
NOTE: Only one screw should be loosened on only one side
of the cart base.
3. Add six bumpers (M) to top of base support. (See Figure 3)
4. Place base support inside legs of cart and push toward cart
back. (See Figure )
Figure 3
3
2
(B)
(C)
(E)
(F)
(J) x 8
1
(H) x 2
(K) x 2
Cart
4
Base support
2
3
(M) x 6

PAC735 Installation Instructions
6
5. Push base support back until it snaps in behind front cap of
cart base. (See Figure 4)
6. Tighten button head cap screw on cart side which was
loosened in Step 2. (See Figure 4)
7. Tighten two 5/16-18 x 1/2" square head cap screws (H) from
Step 1 further into cart until base support is secured to cart.
(See Figure 4)
Figure 4
Mount Storage Cabinet
1. Place storage cabinet (A) on top of base support. (See
Figure 5)
Figure 5
2. Place clamp bracket (D) around cart/stand and line up with
holes on back of storage cabinet (A). (See Figure 6)
3. Insert four 5/16-18 x 1" button head cap screws (G) through
clamp bracket holes and into holes on back of storage
cabinet (A). (See Figure 6) and (See Figure 7)
Figure 6
Figure 7
4. Open either door on accessory to install remaining four
5/16-18" hex nuts (J) onto four 5/16-18 x 1" button head cap
screws (G) until accessory is fully secured to cart/stand.
(See Figure 6)
5. Remove the protective layer from both the inside and
outside of glass.
6. Up to three storage cabinets can be stacked vertically on
top of each other per cart/stand. Repeat steps 1-4 for
additional cabinets and use holes on top of cabinets to bolt
cabinets together.
5
(H) x 2
6
Base support
Front cap
of cart
7
(A) Cart
(A)
(rear view)
(D)
(G) x 4
3
2
[Attaching
to cart]
(rear view)
(A)
(D)
2
(G) x 4
3
[Attaching
to stand]

Installation Instructions PAC735
7
Rack Installation (Optional)
1. Open windowed door.
2. Slide rack equipment (not included) into storage cabinet.
NOTE: Each storage cabinet supports 19" (483 mm) wide rack
mount equipment and has a capacity of 4 U.
3. Use #10-32 cage nuts (not included) to secure storage
racks to storage cabinet.

PAC735 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003114 Rev00
2019 Legrand | AV
www.legrandav.com
02/19