Leigh Country TX 93582 User manual

IMPORTANT: READ CAREFULLY BEFORE BEGINNING
1. Make sure that all parts and hardware are present
before assembly.
2. Assemble on an a non-marring and level surface
3. Do not completely tighten all nuts and bolts until
the swing is fully assembled.
INSTRUCTION MANUAL
CLASSIC PORCH SWING
Product Dimensions:
L: 54”x W: 26”x H: 24.8”
Product Weight:
29.8 lbs
ITEM#: TX 93582
TX 93583
Tools Required for Assembly Tools Included
Mallet
Socket & Wrench Phillips
Screwdriver
Power tools are not recomended while assembling this product.

PACKAGE CONTENTS
F G H
I J
A B C D E
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
A Seat 1 F Eye Bolt 4
B Back 1 G Nut (preassembled to Eye
Bolt (F)) 4
C Arm 2 H Washer (preassembled to
Eye Bolt (F)) 4
D Post 4 I Set Bolt 2
E Back Post 2 J Chain 2
HARDWARE CONTENTS (not shown actual size)
AA BB CC DD
Bolt
Qty. 6
Screw
Qty. 6
Small Button
Qty. 6
Large Button
Qty. 6
EE
Wrench
Qty. 1
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
• This product is intended for use on a covered porch or indoors.
• Weight capacity: 500 lbs.
NOTICE: As with all furniture, proper assembly is necessary for the safe and comfortable use of the
swing. The manufacturer cannot be responsible for any damage or injury that results from improper
assembly of the swing. Please read and follow these instructions carefully and in sequence.

PREPARATION
Before beginning assembly of this product, make sure all parts are present. Compare parts with the
package contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included): Phillips screwdriver, Crescent or 9/16 in. wrench,
Hammer.
ASSEMBLY INSTRUCTIONS
1. Lay the seat (A) on the shipping box during assembly
to protect it. Remove the nuts (G) and washers (H)
from eye bolts (F), then use them to attach the posts
(D) to the seat (A).
Note: The opening for the eye bolts (F) should be
facing down.
1
A
D
BB H
G
F
A
D
2. Place the arms (C) on top of the posts (D) as shown. 2
D
C
D
Back Front
D
D
C
3. Secure the arms (C) to the posts (D) with the
screws (BB). Tighten with a Phillips screwdriver (not
included), then cover with small buttons (CC).
Hardware Used
BB Screw x 4
CC Small Button x 4
3
D
C
D
C
EE
D
D
D
D
BB
EE
CC
D
C

4. Stand up the back (B) and attach the back posts (E)
with the bolts (AA), tightening with the wrench (EE).
Note:Ensure the hole pockets on the back posts (E)
are facing outward.
Once all the bolts (AA) are tightened, insert the large
buttons (DD) into the holes and tap in securely with a
hammer (not included).
Hardware Used
AA Bolt x 4
DD Large Button x 4
EE Wrench x 1
4
CC
B
E
AA JJ
DD
B
E
5. Attach the back assembly to the back of the arms
(C) with the bolts (AA). Tighten with the wrench (EE),
then insert the large buttons (DD) into the holes and
tap in securely with a hammer.
Hardware Used
AA Bolt x 2
DD Large Button x 2
EE Wrench x 1
5
C
CC
AA EE
C
DD
6. Attach the back assembly to both sides of the seat
(A) using the screws (BB). Tighten with a Phillips
screwdriver, then cover with small buttons (CC).
Hardware Used
BB Screw x 2
CC Small Button x 2
6
EE
A
BB
A
CC

7. Place each end of one chain (J) through each hole
on the right arm (C) and attach the end links to the
eye bolts (F). Repeat for the other side, then securely
tighten the nuts (G) with the wrench (EE).
Hardware Used
EE Wrench x 1
7
C AA
CF
GG
JGG J
GG
G
8. Locate a ceiling beam that is sturdy enough to
handle the load of the swing and the occupants
(approximately 500 lbs.). Drill 2 vertical 5/32-inch pilot
holes in the center of the ceiling beam, 50 inches
apart. Insert the set bolts (I) and screw them into the
holes until no threads are exposed.
Note:Ensure the alignment of the set bolts (I) are
conducive to the intended swinging motion of the
item.
CAUTION: Incorrect installation of the ceiling hooks
can cause the swing to fall and possibly cause
serious injury to occupants. Be sure to drill the
correct size holes into a sturdy wood beam.
8
Incorrect
Exposed
threads
Correct
No exposed
threads
GG
I
GG
I
9. Hang the chains (J) on the set bolts (I). 9
GG
I
GG
J

DISTRIBUTED BY:
UNITED GENERAL SUPPLY CO., INC.
HOUSTON, TX 77036
www.LeighCountry.com
© 2018 UGS Co., Inc. All Rights Reserved The Char-log finish is copyright protected
Limited Warranty and Care Instructions
ONE (1) YEAR LIMITED WARRANTY (NON-TRANSFERABLE)
This product is covered under United General Supply’s (UGS) one (1) year limited warranty. To the
original purchaser of this piece of furniture, cooler, or accessory; UGS warrants that it will be free
from defects in material and workmanship for up to one year from the date of purchase under
normal use and proper care.
Replacement of defective or missing parts will be sent at no charge to the customer for a period of
30 days from the date of purchase. UGS will no longer be responsible for missing parts or
hardware 30 days after date of purchase. Freight, packaging, labor, or material charges to and
from our customer service center is not covered under the warranty and is therefore the customer’s
responsibility.
The limited warranty does not cover this piece of furniture, cooler or accessory for commercial
purposes, abusive use, damage by modification, freeze damage, rust, fading and issues caused by
improper care.
For minor defects or missing parts/hardware, please contact customer service immediately upon
purchase. Please do not return product to the store unless the product is irreparable. A customer
service agent may help determine whether the damage is reparable and will provide further
instructions.
For returns and refunds, please refer to your local store return policy with proof of purchase.
Proof of purchase (dated register receipt) will be required for warranty claims.
Please register your product warranty at www.leighcountry.com/register.
The use of power tools during assembly may void this warranty.
PROPER CARE INSTRUCTIONS
If left untreated, wood will naturally weather. During long periods of non-use, store furniture or
cooler in covered and dry place. For the least maintenance, place your furniture, cooler, or
accessory under a covered area.
To preserve and maintain the original finish for a stained finish, we recommend that a light
lacquer coating be applied every 4 to 6 months depending on the seasons. For a painted finish,
an acrylic clear coat needs to be re-applied once a year.
We recommended an exterior poly-urethane product that features a clear satin or semi-gloss
finish and a fast drying process.
Customer Service may be reached Monday through Friday from 9:00a.m. to 5:00p.m. CST.
[email protected] OR 1-877-87LEIGH (53444)