LEMEGA DR1 User manual

Owner's manual
LIFE & ALOUD
DR1 PORTABLE DAB & FM RADIO
LIFE & ALOUD
www.lemegaaudio.com
DR1 PORTABLE DAB & FM RADIO
[email protected]
If you have any questions or suggestions, please share with us.

TUNE+ /
TUNE- /
1 2
1. Introduction
Safety Instructions
PLEASE READ THIS OWNER'S MANUAL COMPLETELY BEFORE
OPERATING THIS UNIT AND STORE THIS INSTRUCTION
MANUAL FOR FUTURE REFERENCE.
2.CONTROLS, CONNECTORS
PRODUCT OVERVIEW
12
89
3
7
6
45
2
1. Preset 1,2,3+
3
4. Menu
5. Back
8.Info
7.Power on/off& Select/Snooze/MuteVolume&
9.Source
6. Play/Pause
Unplug this product from the wall outlet before cleaning.
Place the unit on a solid surface.
Do not put it in a closed bookcase or a cabinet that may keep air
from flowing through its ventilation openings.
Do not install near any heat sources, such as radiators, heat
registers, stoves or other appliances that produce heat.
Protect the power cord from being walked on or pinched
particularly at plugs and the point where they exit from the
product.
Servicing is required when the product has been damaged. Do
not attempt to service this product yourself.
Opening or removing covers may expose you to dangerous
voltages or other hazards.
Please contact the manufacturer to be referred to an authorized
service center near you.
To prevent risk of fire or electric shock, avoid over loading wall
outlets, extension cords, or integral convenience receptacles.
Do not let objects or liquids enter the product.
Use proper power sources. Plug the product into a proper power
source, as described in the operating instructions or as marked
on the product.
Clean only with a dry cloth.
●
●
●
●
●
●
●
●
●
●
●
●
●
Do not use this product near water or moisture.

10 11 12
10 DC power in (5V) 12 Battery compartment.
11 Headphones out.
ACCESSORIES INCLUDED
Carefully remove the unit and all accessories from the package.
Please verify that you have all the following accessories before
recycling the gift box.
Owner's Manual
Warranty Card
Power charging cable
GETTING STARTED
UNDERSTANDING THE CONTROL FUNCTIONS
QUICK SETUP
Fully extend the Telescopic antenna to ensure good reception in
both DAB and FM Radio modes. It may be necessary to alter the
position of the DAB Digital Radio and/or the Telescopic antenna to
achieve the best signal.
1
2.
3.
4
5.
6.
7.
1.
.Connect the power cable to the input in the side of the DR1 and
then plug the cable into an outlet or insert the four “AA” batteries into
the battery compartment to power on.
Fully extend the rear telescoping antenna.
Press the Power knob on the front to turn on the DR1.
. When powered on for the first time in DAB mode, the DR1 will
initiate an auto scan. When complete,
The display will indicate how many stations were received. Be sure
the rear antenna is fully extended during the auto scan.
Press the SOURCE button to select the desired source.
Adjust the volume to the desired level using the SELECT knob.
In DAB mode, the TUNE+/TUNE- button allows you to navigate
between different stations.
GUIDE TO FEATURES
PRESET1/2/3+:
Store a station to the preset list - to store a station,
selected your desired radio station, then press
and hold the PRESET 1/2 button for a second
until the LCD display “Preset store #:(Empty)”
to fig.17, or“#: saved radio station” to fig.18.
There are 10 DAB presets and 10 FM presets.
Either press the TUNE+/TUNE- button to select
your desired station preset number or rotate
and push on the SELECT knob to confirm
your selection, the display will show
“Preset # Stored” to fig.19.
Preset 10 DAB stations and 10 FM favorite
Recall a station from the Preset list
1.To recall a preset station, press the “3+” button once, or rotate the
Select knob to select presets station that you have stored. When the
display shows your desired preset number push SELECT knob to
confirm.
Note: If you choose a preset that hasn't been allocated a station,
then “Empty” will be displayed.
stations.
REAR VIEW
3 4

2
3.
4.
5
6.
. TUNE+/ : Press to select the next track under FM/DAB mode;
Press and hold the Tune+ button 2 seconds to auto-scan the stations
under the FM /DAB mode.
TUNE-/ : Press to select the previous track under FM/DAB
mode; Press and hold the Tune- button 2 seconds to auto-scan the
stations under the FM/DAB mode.
Menu: press the MENU to show the MENU for the current mode.
Press again to show now playing screen.
. BACK: press the BACK to return to the previous screen.
: In DAB/FM mode, press and hold PLAY & PAUSE button, it
will automatically scan for the available radio stations.
7. SELECT/ POWER/VOLUME/MUTE/SNOOZE:
a. SELECT: Rotate the SELECT knob scroll through a menu or
station list. Press to the SELECT knob to select the chosen option.
b. POWER: Turn on or back to standby mode (showing clock and
date), or cancel sleep, or cancel alarm function.
1) Push to power the DR1 On or Off (Standby). When powered on
for the first time in DAB mode, It will
automatically scan for the available
radio stations to fig.1.
2) When your DR1 is using power adapter,
press POWER knob to switch 'on' and 'standby'
to fig.2. Unplug the power adapter to turn off
your DR1 completely.
3) When your DR1 is using batteries,
press SELECT knob to switch 'on' and 'off'.
c. VOLUME: Rotate the SELECT knob to adjust the volume up or
down during playback.
d. MUTE: Press the SELECT knob to mute the music when playing.
e. SNOOZE: Press the scroll button to snooze a set time when alarm
sounding.
8
9.
. Info: When in DAB mode, briefly press repeatedly to view DLS
[Dynamic Label Segment], signal strength, PTY [Programme Type],
ensemble, frequency, signal quality, bit rate codec, time, date. In FM
mode, view radio text, PTY [Programme Type], PS [Programme
Service], stereo/mono, time, date etc.
SOURCE: Briefly press to cycle through the sources: DAB, FM.
In FM mode, DR1 will tune to the start of the
available FM range (87.50MHz) or the
last FM station listed to fig.3.
To manually change the FM frequency,
make sure that you have not selected any other sub-menus. Turn the
TUNE+/TUNE- to change the frequency by 0.05MHz.
DAB mode
In DAB mode, press MENU button to enter the menu list to fig.4.
Press the TUNE+/TUNE- button to select
option through the list of menu or rotate
SELECT knob to scroll the menu list.
Then, stop at your preferred option and
Push the SELECT knob to confirm.
The menu options are: full scan/ manual tune/ DRC /prune/ system.
Full scan – under menu list, rotate the SELECT knob to select
“Full scan“through the list of menu, Push the knob to confirm and full
scan starts automatically to fig.4. Once a scan is completed, the
radio returns to play the previously-selected station or first station
on the station list.
Note: if no radio station found, it shows “No DAB station”.
For a better reception, extend the antenna or do the full scan again
in another place.
1.
2.
3. Manual tune – as well as the normal method of scanning, you can
also manually tune to a particular channel/frequency. This can be
useful for adjusting your antenna to achieve the best possible
reception and scanning a particular channel to update the station
5 6

list. Under menu list, press the TUNE+ button or rotate SELECT
knob to select “Manual tune” through the list of menu, Push SELECT
knob to confirm. Rotate SELECT knob to select a particular
channel/frequency and then Push SELECT button to confirm the
setting to fig.5. The display shows a live indication of the received
signal strength on the selected frequency. Adjustments to your
antenna will be manifested in the received signal strength displayed.
4. DRC (Dynamic range compression) – this function reduces the
difference between the loudest and quietest audio being broadcast.
Effectively, this makes quiet sounds
comparatively louder and loud sounds
comparatively quieter.
Options: off (default)/high/low under
menu list, press the TUNE+/TUNE- button or
Rotate SELECT knob to select “DRC” through the list of menu, Push
SELECT button to confirm. Then press the TUNE+/TUNE- button or
Rotate SELECT knob to select a particular setting and Push
SELECT knob to confirm the setting to fig.6.
5
6
. Prune – this removes all invalid stations indicated in the station
list with a '?' in front of the station name.
Under menu list, Rotate SELECT knob
to select “Prune” through the list of menu,
Push SELECT knob to confirm to fig.7.
. System – the System menu options are:
Sleep /Alarm / Equaliser / Time / Backlight /
Language/, Factory Reset /
Software upgrade / SW version to fig.8.
6.1 Sleep – when listening to the radio you can set a period of time
before the radio enters 'standby' mode.
Note: the radio must be active and not in
'standby' mode already.
Under the system menu, Rotate SELECT
knob to select through the list of menu,
push in SELECT knob to confirm Sleep to fig.9.
Then press TUNE-/TUNE+ button or rotate SELECT knob to select
< sleep off / 15mins / 30mins / 45mins / 60mins / 90mins > and Push
SELECT knob to confirm.
6.2 Alarm- Press Menu>System setting> Alarm. There are 2 Alarms,
you can press and hold Play/Pause button to switch to Alarm 2.
Alarm 1 set up: Press SELECT knob to set on time/Source/
Frequency / Volume then push SELECT knob to confirm the settings.
Parameters
Alarm – Off | On
Source – DAB/FM/Buzzer
Frequency - Daily | Once | Weekends | Weekdays
6.3. Time – if there is any DAB+ radio signal,
the machine will automatically update the time,
there is no signal, can also be set manually
to fig.10.
*Set Time/Date: set hour / set minute / set month / set date>
set year > saved
*Auto update options: update from Any / update from DAB /
update from FM / no update
*Set 12/24 hour: 12hour/24 hours
*Set date format: DD-MM-YYYY.
6.4. Backlight – this radio display has a backlight which can be
adjustable. You can select the time out of
the display backlight of your radio. Under
the system menu, press the TUNE+/TUNE-
button or rotate SELECT knob to select
“Backlight” through the list of menu,
Push the SELECT knob to confirm to fig.11.
You can now use the TUNE+/TUNE- button or rotate SELECT knob
to select < 10sec / 20sec / 30sec / 45sec / 60sec / 90sec / 120sec /
180sec / On >, and Push SELECT knob to confirm.
7 8

6.5. Language – the language used for display messages can be
selected from below options: English | Espanol | Francais | Italiano |
Nederlands | Norsk | Polski Suomi | Dansk | Deutsch. Under the
system menu, press the TUNE+/TUNE- button
or rotate SELECT knob to select “Language”
through the list of menu, Push the SELECT
knob to confirm to fig.12. Cycle through
Language menu by press the TUNE+/TUNE- button
or rotate SELECT knob to select, select and
stop at a particular language, Push the SELECT knob to confirm.
6.6.
6.7.
Factory Reset – this function clears all user defined settings,
replacing them with the original default values, so time/date,
preferences/settings, DAB station list and
preset stations are all lost.
Under the system menu, Rotate SELECT knob
to select “Factory Reset” through the list
of menu, Push the SELECT knob to confirm
to fig.13. Then, or rotate SELECT knob to
choose <Yes> and Push the SELECT knob to start the factory reset.
Software Upgrade- From time to time, DR1 may make software
upgrades available with bug Fixes and/or additional features.
This feature is for service centre.
6.8. Software version – this is used to display the current software
version. Under the system menu, or rotate
SELECT knob to select “Software version”
through the list of menu fig.14, Push the
SELECT knob to confirm. Then, the existing
SW version will be showed.
. Scan setting - by default, FM scans stop at a Strong stations only.
Options: Strong stations only / All stations under menu list, rotate
SELECT knob to select a particular option in “Scan setting”, then
Push the SELECT knob to confirm the change to new setting to fig15.
3. Audio setting - by default, all stereo stations are reproduced in
stereo. For weak stations, this may result in poor quality audio. The
audio quality can be improved using mono. Options: Stereo allowed
Forced mono under menu list, rotate SELECT knob to select a
particular option in “Audio setting” , then Push the SELECT knob to
confirm the change to new setting. It will automatically change to
new setting after 3 seconds.
4. System - Please refer to above description point 6 “System”.
2
Model: DR1
Type: Portable DAB & FM Radio
Power output: 1CH X 2W
Power Supply: 5V DC or 4AA batteries [battery not included]
Dimension (mm): 175*106*54MM
Weight: 0.45KG
Specifications are subject to change without notice.
[e-mail]
www.lemegaaudio.com
TECHNICAL SPECIFICATION
FM mode
1. If the DR1 is in FM mode, Press MENU button
to enter the menu list to fig.15. Rotate SELECT
knob to select option through the list of menu.
Then, stop at your preferred option and Push
the SELECT knob to confirm. The menu options are:
scan setting, audio setting, and system.
9 10
If you have any questions or suggestions, please share with us.