Lennox Hearth Products RAVELLE 30 User manual

Report No. 050-S-12b-5
INSTALLATION AND OPERATION MANUAL
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
- Ne pas entreposer ni utilizer d’essence ni d’autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où vous
trouvez.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du fournis-
seur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindie.
- L’installation et l’entretien doivent être assurés par un
installateur ou un service d’entretien qualifié ou par
le fournisseur de gaz.
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result causing property damage, personal injury
or death.
AVERTISSEMENT:Assurez-vousdebiensuivrelesinstruc-
tionsdonnéesdanscettenoticepourréduireauminimum
le risque d’incindie ou d’explosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
• These appliances may be installed in an aftermarket permanently located, manufactured (mobile) home (USA
only), where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other gases unless a certified kit is used.
• Lennox Hearth Products gas-burning appliances are designed for use as a supplemental heater. They are not
intended for continuous use as a primary heat source.
Ravelle™ 30 (RAVL30)
In the Commonwealth of Massachusetts:
• Installation must be performed by a licensed plumber or gas tter
• See Table of Contents for location of additional Commonwealth of
Massachusetts requirements
TM
US
Portland
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat
for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance. If small children are present in the home, it is
recommended that this appliance be fitted with a barrier screen kit. See Page 32 for ordering information.
Direct-Vent Gas
Fireplace Heater
A French manual is available upon request. Order P/N 775,230CF.
Ce manuel d’installation est disponible en francais, simplement
en faire la demande. Numéro de la pièce 775,230CF.
P/N 775,230M Rev. B, 06/2009
Installer: Leave This Manual With The Appliance.
Consumer: Retain This Manual For Future Reference.

2
FOR YOUR SAFETY do not install or operate your
Ravelle™ 30 gas fireplace without first reading and
understandingthismanual.Anyinstallationoroperation
of the appliance deviating from that which is stated in
this manual WILL void the warranty and may be hazard-
ous.
INSTALLATION AND REPAIR SHOULD ONLY BE DONE BY
A QUALIFIED SERVICE TECHNICIAN. DO NOT ATTEMPT
TO SERVICE THE APPLIANCE YOURSELF.
The fireplace should be inspected and cleaned before
use and at least annually by a qualified service techni-
cian. More frequent cleaning may be required due to
excessive lint from bedding material, carpeting, etc.
It is imperative that control compartments, burners and
circulating air passageways of the room heater be kept
clean.
Adequate clearances around the combustion chamber
and accessibility clearances for servicing and proper
operation must be maintained.
Turn off the gas before servicing this appliance. It is
recommended that a qualified service technician per-
form an appliance check-up at the beginning of each
heating season.
All installations must conform with all local, state
and national codes. In the absence of local codes, the
installation must conform with National Fuel Gas Code
ANSI Z223.1-latest edition, also known as NFPA 54
(In Canada, the current CAN/CSA B149.1 installation
code). Refer to the National Fuel Gas Code and local
zoning and code authorities for details on installation
requirements. Your Ravelle 30 gas fireplace must be
vented to the outside in accordance with the latest edi-
tion of the National Fuel Gas Code.
This gas fireplace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached to
a chimney serving a separate solid fuel burning appli-
ance. Each gas appliance MUST USE a separate vent
system. Common vent systems are PROHIBITED.
MobilehomeinstallationsmustconformwiththeMobile
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (in Canada CAN/CSA Z240 MH), or, when such
a standard is not applicable, the Standard for Mobile
Home Installations, ANSI A225.1 - latest edition.
The appliance, when installed, must be electrically
grounded in accordance with local codes or in the ab-
sence of local codes, with the National Electrical Code,
ANSI/NFPA 70 - latest edition. In Canada, the current
CSA C22-1 Canadian Electrical Code - latest edition.
Do not make any make-shift compromises during in-
stallation. Any modification or alteration may result
in damage to the appliance or dwelling and will void
the warranty, certification and listings of this unit.
Failure to use manufacturer provided parts, variations
in techniques and construction materials or practices
other than those described in this manual may create
a fire hazard and void the limited warranty.
Your Lennox Hearth Products gas fireplace must be
equipped for the proper fuel type and altitude at which
it will be operated. Any operation outside the param-
eters outlined in this manual may result in a hazardous
condition and will void the warranty. Please carefully
read the sections pertaining to these subjects and/or
be sure your appliance is properly equipped.
Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
Due to high temperatures, the fireplace should be lo-
cated out of traffic areas and away from furniture and
draperies.
Children and adults should be alerted to the hazards
of high surface temperature and should stay away to
avoid burns or clothing ignition. Young children should
be carefully supervised when they are in the same room
as the Lennox Hearth Products gas fireplace. Clothing
or any other flammable material should not be placed
on or near the fireplace.
Never use solid fuels such as wood, paper, cardboard,
coal, or any flammable liquids, etc., in this appli-
ance.
Any grill, panel, or glass removed for service MUST be
replaced prior to operating the fireplace. Do not oper-
ate appliance with the glass front removed, cracked,
or broken. Replacement of the glass should be done
by a qualified service technician.
DO NOT USE abrasive cleaner on the glass door as-
sembly. DO NOT ATTEMPT to clean the glass door when
it is hot.
Gold and nickel plated surfaces must be cleaned with
glass cleaner and a clean soft cloth before firing the first
timeorfingerprintswillremainpermanently. NEVERuse
brass polish to clean gold or nickel, this will remove
the plating!!!
Lennox Hearth Products, its employees, or any of its
representatives assume no responsibility for any dam-
ages caused by an inoperable, inadequate, or unsafe
condition as a result of any improper operation, service
or installation procedures, whether direct or indirect.
INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN
WITH THE HOME OWNER!
IMPORTANT SAFETY AND WARNING
INFORMATION

3
CONGRATULATIONS!
When you purchased your new gas fireplace, you joined the ranks of
thousands of individuals whose answer to their home heating needs
reflects their concern for aesthetics, efficiency and our environment.
We extend our continued support to help you achieve the maximum
benefit and enjoyment available from your new gas fireplace.
Thank you for selecting a Lennox Hearth Products gas fireplace as the
answer to your home heating needs.
TABLE OF CONTENTS
Cautions and Safety ........................................................ 2
Using this Manual .......................................................... 3
Orifice Size/Altitude Adjustment.......................................... 4
Codes and Approvals....................................................... 4
New York City, New York (MEA) .......................................... 4
Commonwealth of Massachusetts Requirements...................... 4
Pre-Installation............................................................ 5-6
Features ............................................................ 5
Venting.............................................................. 5
Fuel.................................................................. 5
Specifications...................................................... 5
Packaging List ..................................................... 5
Preparing your Ravelle™ 30 Fireplace for Installation ..... 6
Dimensions ........................................................ 6
Clearances to Combustibles..................................... 6
Installation............................................................... 7-11
Framing Dimensions ............................................. 7
Raised Installations .............................................. 8
Hearth Extension Considerations ............................... 8
Facing Installation Considerations ............................. 9
Face Installation ................................................. 11
Vent Installation ....................................................... 12-18
Application ........................................................ 12
Vent Parts List .................................................... 12
Vent Considerations ............................................. 13
Horizontal Vent Installation..................................... 14
Vertical Vent Installation........................................ 14
Vertical Vent Termination Clearances ........................15
Flue Restrictors .................................................. 16
Horizontal Terminations......................................... 17
Vertical Terminations............................................ 17
Horizontal Vent Termination Clearances ..................... 18
Brick Panel and Log Set Installation.................................... 19
Electrical Connections .................................................... 20
Gas Line Installation ...................................................... 21
Gas Pressure Requirements.................................... 21
LP and Natural Gas Supplies................................... 21
Increasing Efficiency And Hot Air Movement .......................... 22
Operation................................................................ 23-27
Operating Instructions........................................... 23
Pre-Lighting Checklist........................................... 23
Lighting Instructions............................................. 23
Flame Color and Behavior ...................................... 25
Air Shutter Adjustment .......................................... 25
Paint Curing....................................................... 26
Quiet Operation................................................... 26
Blower Operation................................................. 26
Optional Wall Thermostat....................................... 26
Operating Options................................................ 27
Millivolt Control System ........................................ 27
Maintenance and Servicing .......................................... 28-29
Maintenance Checklist .......................................... 28
Vent Pipe Maintenance.......................................... 28
Opening and Removing Door................................... 29
Glass/Door Maintenance........................................ 29
Blower Removal.................................................. 29
Fuel Conversion .................................................. 29
Troubleshooting ............................................................ 30
Replacement Parts ........................................................ 31
Accessories............................................................. 32-33
Fireplace Labels ....................................................... 34-35
Product Reference Information .......................................... 36
USING THIS MANUAL
Please read and carefully follow all of the instructions found in this
manual. Please pay special attention to the safety instructions provided
in this manual.
PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE

4NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation of these fireplaces are approved for installation in New York
City in the US state of New York (MEA#: 138-07-E).
NEW YORK CITY, NEW YORK (MEA)
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
(Massachusetts Approval #G3-0806-6)
These fireplaces are approved for installation in the US state of Mas-
sachusetts if the following additional requirements are met:
• Install this appliance in accordance with Massachusetts Rules and
Regulations 248 C.M.R. Sec. 5.08 2(a) through 2(e).
• Installation and repair must be done by a plumber or gas fitter licensed
in the Commonwealth of Massachusetts.
• The flexible gas line connector used shall not exceed 36 inches (92
centimeters) in length.
• The individual manual shut-off must be a T-handle type valve.
Massachusetts Horizontal Vent Requirements
In the Commonwealth of Massachusetts, horizontal terminations installed
less than seven (7) feet above the finished grade must comply with the
following additional requirements:
• A hard wired carbon monoxide detector with an alarm and battery
back-up must be installed on the floor level where the gas fireplace
is installed. The carbon monoxide detector must comply with NFPA
720, be ANSI/UL 2034 listed and be ISA certified.
• A metal or plastic identification plate must be permanently mounted to
the exterior of the building at a minimum height of eight (8) feet above
grade and be directly in line with the horizontal termination. The sign
must read, in print size no less than one-half (1/2) inch in size, GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.
• Must conform with all local, state and national installation codes.
In the absence of local codes, the installation must conform with
National Fuel Gas Code ANSI Z223.1 - latest edition, also known
as NFPA 54 (In Canada, the current CAN/CSA B149.1 installation
code). Refer to the National Fuel Gas Code and local zoning and
code authorities for details on installation requirements.
• Mobile home installations must conform with the Mobile Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (in Canada
CAN/CSA Z240 MH), or, when such a standard is not applicable,
the Standard for Mobile Home Installations, ANSI A225.1 - latest
edition.
• Must be vented directly to the outside in accordance with the latest
edition of the National Fuel Gas Code and must never be attached
to a chimney serving a separate solid fuel burning appliance.
• Has been certified for use with either natural gas or propane.
• Is not for use with solid fuels.
• Is approved for sitting rooms and/or bedrooms.
For altitudes above 2,000 feet (In Canada 4,500 FT/1370 M), the orifice
should be de-rated by 4% for every 1,000 feet to maintain the proper
ratio of gas to air. Improper orifice sizing my result in damage and
unsafe conditions. Changing the orifice should only be done by a quali-
fied service technician. Contact your Lennox Hearth Products dealer for
proper orifice sizes.
Since there are always several potential sources of fire in any home, we
recommend installing smoke detectors. If possible, install the smoke
detector in a hallway adjacent to the room (to reduce the possibility of
occasional false activation from the heat produced by the appliance). If
your local code requires a smoke detector be installed within the same
room, you must follow the requirements of your local code. Check with
your local building department for requirements in your area.
Certification
Gas appliances must be tested and certified by a nationally recognized
testing and certification laboratory to ANSI (American National Standard
Institute) gas appliance safety standards.
This fireplace has been tested and certified by OMNI -Test Laboratories
to ANSI Z21.88 / CSA 2.33 Standard for Vented Gas Fireplace Heater
and CGA 2.17-M91 and UL 307B Gas Burning Heating Appliances for
Manufactured (Mobile) Homes in both USA and Canada.
It has met all necessary ANSI Standards and is fully certified for installa-
tion in any community. If there are any questions or if you need further
substantiation either write to or call your Lennox Hearth Products dealer.
If you have further questions, please contact Lennox Hearth Products.
Checkall local buildingandsafetycodesbeforeinstallation.The installation
instructions and appropriate code requirements must be followed exactly
and without compromise. In the absence of local codes the following
standards and codes must be followed.
ORIFICE SIZE/ALTITUDE ADJUSTMENT
SMOKE DETECTORS
CODES AND APPROVALS
THE RAVELLE™ 30 FIREPLACE

5
PRE-INSTALLATION
Features
Installation Options
Residential
Vented vertical and horizontal
Manufactured (mobile) home
Natural gas (NG) or propane (LP)
Bedrooms
Optional wall-mounted or remote thermostat
Venting
This fireplace can be vented with Security™ Secure Vent™ pipe*. Coaxial
pipe diameters are 6-5/8” outer and 4” inner. The combustion air for this
fireplace is drawn from outside the house through the outer DV (direct
vent) pipe. Room air is not required for combustion.
When planning your installation, select the correct length of vent pipe
for your particular requirements. Determine the minimum clearance to
combustibles from the rear of the unit to the wall. It is also important to
note the thickness of the wall. Before cutting the vent hole through the
wall make sure that ALL vent and termination clearances (see Pages 15
- 18)will be met.
Electrical
The standard fan motor requires 120 Volts AC for operation. The fireplace
is not dependent on the fan or an outside electrical supply to operate.
Millivolt Valve
This fireplace is operated with a millivolt valve and therefore burns even
during a power outage.
Fuel
This fireplace comes from the factory equipped to burn natural gas at a
specified elevation. The fireplace can be converted to burn LP gas (liquid
propane) by changing the cassette (valve and pilot assembly) or installing a
conversion kit. Only Lennox Hearth Products conversion kits can be used to
convert from NG to LP or LP to NG. Contact your Lennox Hearth Products
dealer for details.
Specifications
Fireplace weight: 200 lbs
Pipe:Type - direct-vent
Recommended manufacturer*
Security Secure Vent*
Diameter - 6-5/8”x 4” for all installations
Packaging List
The Ravelle™ 30 gas fireplace comes with the following parts:
1 Fireplace Body with Burner Cassette
1 Log Set
1 Set of Refractory Brick Panels (3 pieces)
1 Bag of Ember Material
1 Installation and Operation Manual
Decorative Faces - One Required
Arch Inset
Classic Inset
Screen
Foundry™
Cast Pillar
Brick Liners - One Required
Standard Tan Brick
Red Brick
Note: See Pages 32 and 33 for ordering information.
* Other approved chimney brand is Simpson Dura-Vent DV-GS.
RATINGS
Ravelle 30 (RAVL30)
NATURAL GAS LP GAS
Max/Min Input BTUh 0-2,000 Feet (0-610 M)u
30,000 / 20,000 28,500 / 20,000
Manifold Pressure (IN. WC) 3.5 / 1.7 11 / 5.4
Min. Inlet Pressure (IN. WC) 5 11
Maximum heat output BTUs/hour-steady state 24,600 23,370
P4 Efficiency w
56.88% 67.04%
Orifice (DMS) 0-2,000 Feet (0-610 M)u
#37 #51
uUnit factory equipped for 0-2000 FT/0-610 M, In Canada 0-4500 FT/0-1370 M
vThe Steady State Efficiency numbers based on maximum vent configuration.
wTested to CSA P.4.1-02 “Testing Method for Measuring Annual Fireplace Efficiency.
Electrical Rating: 120 VAC, 60 HZ, Less Than 2 Amps
Ductability (optional)
Whole Home Comfort
System

6NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
uThe center of the access hole for the gas piping is located at the
left side of the fireplace 6-1/4” back from the front edge and 2-1/8”
up from the base of the unit.
vThe electrical access is located at the right lower rear of the fire-
place.
wThese dimension include the 3/4” stand-offs.
Dimensions
u
35-1/2”
(902mm)
21”
(533mm)
41”
(1041mm)
24-1/4”
(616mm)
33”
(838mm)
40-3/4”
(1035mm)
8-1/2”
(216mm)
27-1/8”
(689mm)
24-1/2”
(622mm)
v
Preparing Your Ravelle™ 30 Fireplace For Installation
Read all instructions before beginning your installation. If instructions
have not been read carefully, your installation could void your warranty
and may create a serious fire, health, or other safety hazard.
The Lennox Hearth Products warranty will be voided if one of the fol-
lowing occurs:
• Installation of any damaged fireplace or vent system compo-
nent.
• Unauthorized modification of the direct vent system.
• Installation other than as instructed by Lennox Hearth Products,
Security™, or Simpson Dura-Vent.
• Installation of any fireplace or vent system component not
manufactured or approved by Lennox Hearth Products, Security
or Simpson Dura-Vent.
When planning the installation for your Ravelle 30 gas fireplace, it’s
necessary to consider the following:
• Where the unit is to be installed
• The vent system configuration to be used
• Gas supply (NG or LP)
• Electrical wiring
• Framing and finishing
• Optional accessories
Clearances to Combustibles
Minimum clearances include any projections such as shelves, window
sills,mantels,spacers/standoffsorsurfacestocombustibleconstruction
etc. above the appliance. Paint or lacquer used to finish the mantel
must be heat resistant in order to avoid discoloration.
Minimum clearances to combustible materials in inches:
Front corners to enclosure (from standoffs) - 0 (0mm)
Rear corners to enclosure (from standoffs) - 0 (0mm)
Top to header (from standoffs) - 0 (0mm)
Bottom of unit to floor - 0 (0mm)
Edge of door glass to side wall and side trim - 6-1/4” (159mm)
Back to enclosure (from standoffs) - 0 (0mm)
Mantel: The drawing at the lower right shows the minimum distances
from the base of the fireplace to combustible mantel and facing mate-
rial. Combustible materials may be placed above and withing the shaded
areas. If your fireplace has an arched face, the combustible mantel fac-
ing material may curve with the arch of the face as long as a minimum
distance of 10” (254mm) is maintained between the top of the face and
the combustible facing material.
Hearth Protection: If the vertical distance from the base of a Ravelle
30 gas fireplace to a combustible surface is less than 1”, then a hearth
protection is required in front of the unit. The required hearth protec-
tion must extend 10” (254mm) out from the front of the unit with a
width of 41” (1041mm) and include a minimum of 1/2” (13mm) thick
non-combustible material. If the vertical distance from the base of the
unit to the combustible surfaces is 1”(25mm) or greater, then no hearth
protection is required.
Pipe Clearances: On all vertical runs of pipe, a 1” (25mm) clearance
between the direct vent pipe and combustibles must be maintained.
w
w
Figure 1
When an 18” (457mm) or longer section of pipe is installed vertically,
directly off the top of the unit, then any horizontal run of pipe must
maintain clearances to combustibles of 2” (51mm) on the top and 1”
(25mm) on the sides and bottom. When less than 18” (457mm) of pipe
is installed vertically, directly off the top of the unit, then any horizontal
run of pipe must maintain clearances to combustibles of 6” (152mm)
on the top and 1” (25mm) on the sides and bottom. See Page 17 for
allowable pipe configurations.
Mantel and Facing
Material (side view)
Fireplace side view
(drawing not to scale)
Base of Fireplace
5”
(127mm)
3”
(76mm)
45°
39”
(991mm)
38-1/2”
(978mm)
37”
(940mm)
34”
(864mm)
24”
(610mm)
10”
(254mm)
Figure 2

7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Framing Dimensions
The dimensions given below are minimum framing distances necessary
to maintain safe clearances between the Ravelle™ 30 gas fireplace and
combustible materials.
uIf the unit is to be vented horizontally with a 90º elbow right off the
top of the fireplace and directly through an exterior wall, then a hole
9-1/4” x 10-3/4” (235 mm x 273 mm) square with a center line 34”
(864 mm) above the base of the fireplace will accommodate the wall
thimble and direct vent pipe.
vThe gas line should be routed to the left side of the unit. The access
hole in the fireplace for the gas line is 6-1/4” (159 mm) back from
the front edge and 2-1/8” (54 mm) up from the base of the unit. If
the gas line enters the unit from the right side, the piping will need to
be disconnected to remove the fan.
If a wall-mounted on/off switch or thermostat is to be used, these
wires should be routed to the left front of the unit for access to the
fireplace. The wire should be fed through the gas line hole, along the
gas line, to the valve.
wThe electrical power supply wiring should be routed to the right rear
of the unit.
Note: The fireplace may be placed directly on wood or non-combustible
flooring, but not on vinyl floor covering or carpet.
Framing Suggestions: The framing header above the front of the
fireplace should be as narrow front to back as allowable to give maximum
clearance to the direct vent pipe (i.e. don’t use a 6” (152 mm) thick header
when a 4” (102 mm) thick one is allowed). A 6” (152 mm) header may
need to be notched to accommodate vertical vent pipe. If the fireplace is
going to be horizontally vented directly out the back, do not place a stud
in line with the wall thimble. If a hearth extension greater then 1” (25mm)
thick is going to be used, the fireplace and the header must be raised
accordingly. See Hearth Extension Considerations for further details.
Insulation: The exterior walls adjacent to the fireplace should be
insulated like the rest of the house, but insulation should not be placed
around the fireplace or vent pipe.
Corner Installations: The dimensions below are minimum and show
the stand-offs on the rear corners of the fireplace up against the corner
walls.
u
v
w
14-1/8”
(1359mm)
41-1/2” (1054mm)
41-1/2”
(1054mm)
21”
(533mm)
41”
(1041mm)
47-3/4”
(1213mm)
67-1/2” (1715mm)
13”
(330mm)
Figure 3
Figure 4
INSTALLATION

8NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Raised Installations
The fireplace may be raised by building a platform of sufficient strength to
support the fireplace and pipe. When building a raised hearth extension,
please see the note below regarding height of the fireplace in relation to
the thickness of the hearth extension material.
Hearth Extension Considerations
It is IMPORTANT to note that there is a 1” space between the base of
the fireplace and the bottom of the fireplace face. See Page 6 for hearth
extension requirements. This space will allow a 7/8” (22 mm) thick hearth
extension (including backer board if desired). Should a hearth extension
thicker than 7/8” (22 mm) be desired, the height of the fireplace must
be raised the thickness of that hearth extension less the 7/8” (22 mm).
For example, if a 2-7/8” (73 mm) thick cultured stone is to be placed
on the floor to serve as the hearth extension, then the fireplace must be
raised 2” (possibly using 1/2” (13 mm) plywood over 2 x 4’s laid flat)
to accommodate the 2-7/8” (73 mm) stone. It is important to note that
if the fireplace is raised, then it is necessary to raise the height of the
header above the stand-offs an equal amount.
Raised Platform
for Hearth Exten-
sion and Fireplace
Raised
Platform
Nailing
Plate
Base of Fireplace
One Inch Space
Fireplace
Face
Figure 5
Figure 6
Figure 7
Raised Platform
for Hearth Exten-
sion and Fireplace
Raised
Platform
Fireplace
Face

9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
The screws should be driven through the cement board into the outer
metal skin of the fireplace. The sheetrock (drywall) is then butted up
to the cement board. The sheetrock above the fireplace should also be
fastened to the fireplace by driving screws into the outer metal skin of
the fireplace.
Facing Less Than 1” Thick: If the combined thickness of the facing
material (eg. 3/8” [9.5 mm] thick ceramic tile and 1/2” (13 mm) thick
cement board) is less than 1” (25 mm), then the tile can be placed behind
the fireplace (see below).
Cement Board
3/8” Tile and 1/2” Cement
Board Behind Fireplace Face
Cement Board - a minimum
of five inches wide.
Sheetrock
1” Reveal
5” (127mm)
Minimum
Sheetrock
Facing Installation Considerations
Non-combustible cement board (such as Wonderboard, Durock, or Har-
dybacker) must extend 10” (254 mm) above the 1” (25mm) top reveal
and a minimum of 5” (127 mm) from each side reveal (see drawing below
- right). This cement board may be 1/4” (6.3 mm) thick or greater, but
would normally be the thickness of the drywall - for example 1/2” (13
mm). The cement board may be fastened with drywall screws.
Cement Board - minimum
of 5” (127 mm) wide
3/8” (9.5 mm) Tile and 1/2” (12.7 mm)
Cement Board Behind Fireplace Face
10” (254mm)
Minimum
(25mm)
Figure 8

10 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Facing Greater Than 1” (25mm) Thick:
If the combined thickness of the facing material (eg. brick or cultured
stone) and cement board is greater than 1”, then the facing material must
be placed around the face. A template (see kit part numbers below) should
beused while installingthe facing material. Templatesforthe various faces
may be purchased from your Lennox Hearth Products dealer. Instructions
for installing the templates are included with the templates.
Template part numbers:
Arch Inset #75206
Classic Inset #75209
Foundry™ #75090
Adjustment prior to arched face installation:
The corners of the 1” (25mm) reveal around the fireplace opening need to
be adjusted prior to installing an arched face (see below). Remove screws
A and loosen screw B. Rotate the corner downward bending the metal at
pivot point C until the holes from which screws A were removed line up
with the lower set of holes. Reinstall screws A and tighten screw B. When
finished, the corners should look like the corner below at the far right.
Figure 10
Figure 11
Figure 12
Figure 9
Platform to raise fireplace to accommodate a
hearth extension greater than 1” in thickness.
Template
Template
Reveal Corner
Reveal Corner
Expanded View of
Reveal Corner
A
B
C
Expanded View of Reveal Corner
A
B
C
A
A
Reveal Corner Adjusted
for Arch Face
Reveal Corner Adjusted
for Arch Face

11
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2. Bracket C in the lower diagram is installed on the face during the
face assembly (see instructions included with face). The captive
screws D on this bracket should be screwed into captive nuts E on
the fireplace. A phillips head screw driver inserted through the vent
holes in the face can be used to complete this task. Align the face for
plumb and level and then tighten all 4 screws.
CAUTION: Any masonry that has been cleaned with an acid
wash must be properly neutralized before installing the fire-
place face. The acid wash will tarnish the face. Consult your
masonry installer.
Face Installation
A number of different faces are available for the Ravelle™ 30 gas fireplace,
however, all the faces are installed in a similar manner. A total of 4 screws
(2 upper and 2 lower) attach the face to the fireplace. To install a face:
1. Locate the 2 screws found in the hardware bag shipped with the face.
Position the face (with the lower door open) in front of the fireplace.
Install the 2 screws (A in the diagram below) through the holes in the
lower door hinge bracket and screw them into the captive nut on tab B
located on the fireplace. Do not fully tighten these screws yet.
A
B
CD E
Expanded View
Expanded View
Figure 13

12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Application:
The Ravelle™ 30 gas fireplace, has been tested and listed as a direct
vent heater system by OMNI-Test Laboratories, Portland, Oregon and is
recommended for use with Security™ Secure Vent™ pipe.
IMPORTANT:
• Read all instructions carefully before starting the installation.
Failure to follow these instructions may create a fire or other
safety hazard and will void the warranty. Be sure to check for
specific clearances to combustible requirements on Page 6.
Do not extend the venting system vertically or horizontally in
excess of the distance prescribed on Page 17.Consult your
local building codes before beginning the installation.
• Always maintain the proper air spaces (see Page 6) between
theventpipeandnearbycombustiblestopreventafirehazard.
Do not fill air spaces with insulation. Be sure to check the
venttermination clearancerequirements from decks,windows,
soffits, gas regulators, air supply inlets and public walkways,
as specified in these installation instructions on Page 18 and
local building codes.
• Thisgas applianceand ventsystem mustbe vented directly to
the outside of the building and never be attached to a chimney
serving a separate solid fuel or gas-burning appliance. Each
directventgasappliancemustuseitsownseparateventsystem.
Common vent systems are prohibited.
• The Ravelle 30 gas fireplace is recommended for use
with Security Secure Vent pipe. The appliances and vent
manufacturerswarrantieswillbe voidedandseriousfire,health,
or other safety hazards may result from any of the following
actions:
• Installation of any damaged direct vent component.
• Unauthorized modification of the direct vent system.
• Installation of any vent component part not approved or
manufactured by the approved vent manufacturer.
• Installation other than as instructed by Lennox Hearth
Products and vent manufacturers instructions.
Vent Parts List
DirectventpipeSecurity™SecureVent™*may beused with the Ravelle30
gas fireplace. Please see the lists below to verify the components available
fromeachdirectventpipemanufacturer. Snorkelterminationsareavailable
for applications which may require vertical rise on the building exterior.
The components listed below come in a galvanized finish. Most of the
components are also available in a painted black finish. Add a “B” to the
end of the part number when ordering if a black part is desired.
Security™ Secure Vent 6-5/8”x 4” Pipe
Part Number Description
SV4L6 6” Pipe Length
SV4L12 12” Pipe Length
SV4L24 24” Pipe Length
SV4L36 36” Pipe Length
SV4L48 48” Pipe Length
SV4LA 6” Pipe, Adjustable
SV4LA12 12” Pipe, Adjustable
SV4FA Flashing, 1/12 to 176/12 Roof Pitch
SV4FB Flashing, 8/12 to 12/12 Roof Pitch
SV4RSM Wall Radiation Shield
SV4E46 45° Elbow
SV4E90 90° Elbow
SV4VS Vinyl Shield Protector
SV4FC Storm Collar
SV4CGV Vertical Termination Cap
SV4BF Firestop
SV4CHC Horizontal Termination Cap
SV4STC36 Snorkel Termination (36”) Cap
SV4STC14 Snorkel Termination (14”) Cap
SV4BM Wall Band
Simpson DuraVent 6-5/8”x 4” GS Pipe
Part Number Description
908 6” Pipe Length
907 9” Pipe Length
906 12” Pipe Length
904 24” Pipe Length
903 36” Pipe Length
902 48” Pipe Length
911 11” to 14-5/8” Pipe, Adjustable
912 12” to 17” Pipe, Adjustable
917 17” to 24” Pipe, Adjustable
942 Wall Thimble
943 Flashing, 0/12 to 6/12 Roof Pitch
943S Flashing, 7/12 to 12/12 Roof Pitch
945 45° Elbow
950 Vinyl Siding Standoff
953 Storm Collar
963 Ceiling Firestop
980 Vertical Termination
981 Snorkel Termination (36”)
982 Snorkel Termination (14”)
984 Horizontal Square Termination
985 Horizontal Square Termination (High Wind)
988 Wall Strap
991 Vertical Termination (High Wind)
VENT INSTALLATION

13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 14
Vent Considerations
Twist-lock procedure: Four indentations, located on the female ends
of pipes and fittings, are designed to slide straight onto the male ends
of adjacent pipes and fittings by orienting the four pipe indentations so
they match and slide into the four entry slots on the male ends (see
Figure 14). Push the pipe sections completely together, then twist-lock
one section clockwise approximately one-quarter turn until the two sec-
tions are fully locked. The female locking lugs will not be visible from
the outside on the pipe or fittings. They may be located by examining
the inside of the female ends.
Supports: Horizontal runs of vent must be supported every three feet.
Wall straps are available for this purpose.
Pipe Sealing: If Security™ Secure Vent™ pipe is used, then sealant is
required at only the first pipe joint attaching the pipe to the flue collar on
the fireplace. If Simpson Dura-Vent GS pipe is used, then the pipe must
be sealed as follows: seal both the inner and outer pipes with a high
temperature silicone sealant rated for at least 600º F (commonly known
as “RTV”). Run a 1/8” (3 mm) bead of silicone around the outside of the
male end of the outer sleeve. Run a 1/8” (3 mm) bead of silicone about
1/4” (6 mm) from the end of the male inner pipe, which is found in the
pipe to be attached above. Twist-lock the pipes or fittings together.
Sealant
Female
Locking
Lugs
Male
Locking
Lugs

14 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Horizontal Vent Installation
IMPORTANT NOTES:
1. All Ravelle™ 30 gas fireplaces horizontally terminated vent installa-
tions may only use 6-5/8” x 4” Security™ Secure Vent™ or Simpson
Dura-Vent GS direct-vent pipe.
2. When this pipe passes through a wall, a wall thimble - Security part
number SV4RSM or Simpson part number 942 is required. The hole in
the wall for the wall thimble should be 9-1/4” wide by 10-1/4” high.
3. Horizontal runs of vent must be supported every three feet. Wall
straps - Security part number SV4BM or Simpson part number 988
are available for this purpose.
4. If the vent passes through a ceiling or floor, a firestop - Security part
number SV4BF or Simpson part number 1263 - is required.
5. Also note that venting terminals shall not be recessed into a wall or
siding. If installing the termination cap on a wall covered with siding,
a vinyl siding standoff - Security part numberSV4VS or Simpson
part number 1250 - or furring strips must be used to ensure that the
termination cap is not recessed into the siding.
6. The horizontal run of vent must have a 1/4” (6 mm) rise for every one
foot of run towards the termination.
7 If the wall being penetrated is constructed of non-combustible mate-
rial, such as masonry block or concrete, a 7-1/2” (191 mm) diameter
hole is acceptable and a wall thimble is not required.
8. The location of the horizontal vent termination on an exterior wall must
meet all local and national building codes and must not be blocked
or obstructed. For allowable external vent terminations locations, see
the diagram on Page 18.
9. Allowable clearances from the vent pipe to combustible materials
must be maintained. See Page 6 for these clearances.
10.Do not locate the termination cap where it may be blocked by shrub-
bery or snow.
Figure 15
Flashing
Simpson (Part # 943 or 943S)
Secuirty (Part #SV4FA or SV4FB)
Vertical Termination Cap
Security (Part #SV4CGV)
Simpson (Part # 980)
Pipe
Length
CeilingFirestop
Simpson (Part # 963)
Security (Part # SV4BF)
CeilingMinimum
Framing 10” x 10”
(254mm x 254mm)
Storm Collar
Simpson (Part # 953)
Security (Part #SV4FC)
Roof- Maintain 1”
(25mm) Clearance
to Combustibles
Vertical Vent Installation
Figure 16
Note:
Verify that you have
at least the minimum
clearance to combus-
tibles at the roofline.
Elbow
Termination Cap
Security (Part # SV4CHC)
Simpson (Part # 984)
9-1/4”x 10-1/4”
(235mm x 260mm)
Framed Hole
Wall Thimble
Security (Part #SV4RSM)
Simpson (Part #942)

15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
IMPORTANT NOTES:
1) All Ravelle™ 30 fireplace vertically terminated vent installations use 6-
5/8” x 4” Security™ Secure Vent™ or Simpson Dura-Vent GS pipe.
2) If the vent passes through a ceiling or floor, a firestop - Security part
number SV4BF or Simpson part number 963 – is required.
3) If the vent passes through the roof, a roof flashing and storm collar
are required.
4) Allowable clearances from the vent pipe to combustible materials must
be maintained. See Page 6 for these clearances.
5) A maximum of either two 45-degree elbows or two 90-degree elbows
may be used. See Page 17 for allowable offsets.
6) The maximum system height is 30 feet (9.1M) and the minimum is
10 feet (3M).
Vertical Vent Termination Clearances
The vent / air intake termination clearances above the high side of an
angled roof is as shown in the Figure 17.
Termination Heights For Vents
Above Flat Or Sloped Roofs
Ref. NFPA 54 / ANSI Z223.1, 7.6
Roof Pitch * Feet *Meters
Flat to 6/12 1.0 0.3
6/12 to 7/12 1.25 0.38
7/12 to 8/12 1.5 0.46
8/12 to 9/12 2.0 0.61
9/12 to 10/12 2.5 0.76
10/12 to 11/12 3.25 0.99
11/12 to 12/12 4.0 1.22
12/12 to 14/12 5.0 1.52
14/12 to 16/12 6.0 1.83
16/12 to 18/12 7.0 2.13
18/12 to 20/12 7.5 2.29
20/12 to 21/12 8.0 2.44
12
X
Roof Pitch is X/12
2 FT
MIN.
2 FT MIN.
Lowest
Discharge
Opening
H*
*H = MINIMUM HEIGHT FROM ROOF TO
LOWEST DISCHARGE OPENING OF VENT
TERMINATION HEIGHTS FOR VENTS ABOVE
FLAT OR SLOPED ROOFS
Horizontal Overhang
Vertical
Wall
Vent
Termination
Storm Collar
Concentric
Vent Pipe
Flashing
1 inch (25.4 mm) Minimum
Clearance to Combustibles
Figure 17

16 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Flue Restrictors
The flue restrictor settings shown in Figures 19 and 20 are for typical
installations and may need to be adjusted from standard to take into
accountothervariablesintheinstallationto achievepropercombustion.
See Flue Restrictor Guidelines on this page to assist you in making a
proper flue restrictor adjustment.
The Ravelle™ 30 gas fireplace uses balanced flue technology to ensure
proper combustion. As such, flue restrictors may need to be installed
depending on the vent configuration of your fireplace. The drawings on
Page 17 show all the allowable pipe configurations for the Ravelle 30
gas fireplace. To properly install the flue restrictor, first find your pipe
configuration in the drawings on Page 17 and note which restrictor
setting is recommended. The flue restrictors and four black self-tapping
5/32” allen head screws can be found in the firebox in a plastic bag. The
restrictors should be placed over the openings at both sides of the ceil-
ing of the firebox. For each restrictor, two self-tapping 5/32” allen head
screws should be installed in either holes 1, 2, 3, 4, or 5 in the restrictor
and screwed into the two holes in the firebox ceiling. (Note: There are
four holes at each side of the firebox ceiling to receive only two screws.
Insert the screws into either two holes). See Figure 18 for the location of
hole numbers on the restrictor. The numbered holes in which the screws
are inserted in the restrictor should correspond to the restrictor position
numbers found on the drawings for your pipe configuration. Restrictor
positions are based on tests run in a laboratory. The optimum restrictor
positions may need to be adjusted slightly depending on the conditions
surrounding the residential installation. Do not adjust restrictors to a
point where the fireplace is sooting.
Notes: The higher the number of the flue restrictor position, the greater
amount of combustion air will be delivered.
Flue Restrictor Adjustment Guidelines
After the flue restrictors have been set to the standard settings as shown
in Figures 19 and 20, the burner flame appearance should be evaluated
to determined if the flue restrictors need to be set to a different position
to adjust for variables in your installation. Light the appliance and allow
it to burn for 20 minutes. See Flame Color and Behavior on Page 26 to
determine if you have a proper burner flame appearance. If the proper
flame appearance cannot be achieved, the flue restrictor may need to be
set to a different position. See the following guidelines to determine if
you need to readjust the flue restrictors.
Before proceeding, confirm the manifold and inlet gas pressure is correct,
primary air shutter is properly adjusted, venting system connections are
secure and not blocked and if you are at a high elevation, ensure unit has
been properly derated:
Restrictors
Interior of Firebox
Figure 18
Symptoms - Lack of Combustion Air
If the symptoms listed below are present, you may need to adjust the
flue restrictor to a more open position.
• Flame appears yellow
• Floating Flames (lazy, ill defined, quiet, may roll)
• Sooting
• Pilot becomes yellow and appliance shuts down
Symptoms - Excessive Combustion Air
If the symptoms listed below are present, you may need to adjust the
flue restrictor to a more closed position.
• Low Flame
• Pilot pulls and appliance shuts down
• Pilot flame ghosts

17
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Vertical Terminations
The diagram to the below shows all allowable combinations of straight
verticaland offset to verticalventconfigurationswith verticalterminations.
The termination must fall within the shaded areas on the diagram. Use
the restrictor positions indicated. Offsets may consist of two 90º elbows
OR two 45º elbows. The minimum termination height is 11 feet (3.4 M)
and the maximum is 33 feet (10M).
Vertical Terminations
Restrictor
Position #2
Restrictor
Position #5
Restrictor
Position #1
16’ Maximum
Horizontal Terminations
The shaded areas in the diagram below show all allowable combinations
of vent configuration with horizontal terminations. Horizontal sections
of pipe require 1/4” (6.4 mm) of rise for every 12” (305 mm) of run.
A second 90º or 45º elbow (in addition to the first 90º elbow at the top
of the vertical length of pipe) is allowed as long as the overall length of
the horizontal run of pipe does not exceed those shown below. Use the
restrictor positions indicated.
Horizontal Terminations
Restrictor
Position #2
Restrictor
Position #3
Restrictor
Position #4
No Restrictor
Snorkel Terminations: Snorkel Terminations: For installations requiring a vertical rise on the exterior of the building, 14-inch (356 mm) and 36-
inch (914 mm) tall Snorkel Terminations are available. Follow the same installation procedures as used for standard Horizontal Terminations. If the
Snorkel Termination must be installed below grade, (i.e. basement application), proper drainage must be provided to prevent water from entering the
Snorkel Termination. Do not attempt to enclose the Snorkel within the wall, or any other type of enclosure.
20 Ft.
(6M)
15 Ft.
(4.6M)
10 Ft.
(3M)
5 Ft.
(1.5M)
0 Ft.
(0M)
0 Ft.
(0M)
5 Ft.
(1524M)
10 Ft.
(3M)
14 Ft.
(4.3M) 0 Ft.
(0M)
5 Ft.
(1524M)
10 Ft.
(3M)
15 Ft.
(4.6M)
0 Ft.
(0M)
5 Ft.
(1.5M)
10 Ft.
(3M)
15 Ft.
(4.6M)
20 Ft.
(6M)
25 Ft.
(7.6M)
30 Ft.
(9.1M)
Figure 19 Figure 20

18 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Exterior Horizontal Vent Termination Clearance Requirements
V
VV
V
V
F
C
B
B
A
B
H
M
I
XV
D
V
AA
A
V
L
B
J
XE
V
A
G
*18”
18”
B
C
C
C
* See Item D in the Text Below.
Center Line
of Termination
Exterior Wall
Horizontal
Termination
Ventilated Soffit
Inside Corner
DETAIL D
Minimum Clearances Canadian Installation * US Installation **
A = Clearance above grade, veranda, porch, deck
or balcony.
12 inches (30 cm) * 12 inches (30 cm) **
B = Clearance to window or door that may be
opened.
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW),
12 in. (30 cm) for appliances > 10,000 BTU/hr (3kW) and <
100,000 BTU/hr (30kW), 36 inches (91 cm) for appliances
> 100,000 BTU/hr (30kW)*
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW),
9 in. (23 cm) for appliances > 10,000 BTU/hr (3kW) and <
50,000 BTU/hr (15kW), 12 inches (30 cm) for appliances
> 50,000 BTU/hr (15kW)*
C = Clearance to permanently closed window 12 inches (305 mm) recommended to prevent window
condensation
9 inches (229 mm) recommended to prevent window
condensation
D = Vertical clearance to ventilated soffit located
above the terminal within a horizontal distance of 18
in. (458 mm) from the center line of the terminal
18 inches (458 mm) 18 inches (458 mm)
E = Clearance to unventilated soffit 12 inches (30 cm) 12 inches (30 cm)
F = Clearance to outside corner 5 inches (12.7 cm) 5 inches (12.7 cm)
G = Clearance to inside corner 6 in. (15 cm) 6 in. (15 cm)
H = Clearance to each inside of center line extended
above meter / regulator assembly
3 feet (91 cm) within a height of 15 feet above the meter /
regulator assembly *
3 feet (91 cm) within a height of 15 feet above the meter
/ regulator assembly **
I = Clearance to service regulator vent outlet 3 feet (91 cm) * 3 feet (91 cm) **
J = Clearance to non-mechanical air supply inlet
to building or the combustion air inlet to any other
appliance
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW), 12
in. (30 cm) for appliances > 10,000 BTU/hr (3kW) and <
100,000 BTU/hr (30kW), 36 inches (91 cm) for appliances
> 100,000 BTU/hr (30kW)*
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW), 9
in. (23 cm) for appliances > 10,000 BTU/hr (3kW) and <
50,000 BTU/hr (15kW), 12 inches (30 cm) for appliances
> 50,000 BTU/hr (15kW)*
K = Clearance to mechanical air supply inlet 6 feet (1.8 meters) * 3 feet (91 cm) above, if within 10 feet (3 m) horizon-
tally**
L = Clearance above paved sidewalk or paved
driveway located on public property
7 feet (2.13 m) ‡ 7 feet (2.13 m) ‡
M = Clearance under veranda, porch, deck or
balcony
12 in. (30 cm) * ‡ 12 in. (30 cm) ** ‡
* In accordance with the current CSA-B149.1 National Gas and B149.2 Propane Installation Code - Latest Editions.
** In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Codes - Latest Edition.
‡ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
*‡ Only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor.
Inside
Corner Detail
Operable
Window
Fixed
Closed
Window
= 9" in U.S.
= 12" in Canada
3 ft.
3 ft.
= Air Supply Inlet = Vent Terminal = Area where Terminal is NOT permitted
Figure 21

19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 23
Figure 24
Figure 25
Log Installation Instructions
If logs are not installed according to the log installation instructions,
flame impingement and improper combustion could occur and result
in soot and/or excessive production of carbon monoxide (CO), a color-
less, odorless, toxic gas.
The size and position of the log set is critical to achieve a safe, reli-
able and attractive flame pattern. Any attempt to use a different log
set in the fireplace will void the warranty and will result in incomplete
combustion, sooting and poor flame quality.
Parts list: rear log, left front log, right front log, left top log, right top
log and small straight twig
1. Remove the logs from the box and carefully unwrap them. The logs
are fragile so handle them with care.
2. Align the holes in the bottom of the rear log (the longest log in the set)
with the two pegs just to the rear of the rear burner tube and slide the
log down onto the pegs. The charred black surface should face the
front.
3. Rotate the right front log (3018 is cast into its bottom surface) so the
charred black surface is toward the front. Place this log so the two
holes in its bottom surface slide onto the two pegs on the right side
of the air control panel. See Figure 23.
4. Rotate the left front log (3017 is cast into its bottom surface) so the
charred black surface is toward the front and place it on the pegs
protruding from the left side of the air control panel as shown in
Figure 23.
Brick Panel
1. Remove the wrapping around brick panels which are shipped in the
firebox.
2. The long rectangular panel goes in the rear of the firebox - he thin layer
of bricks should be down. The panel rests on 3 metal tabs protruding
from the rear of the firebox about 3” above the firebox floor.
3. On the side panels, the rounded edge goes to the front. Install the side
panels by sliding them along the side of the firebox into retainers at
the top and bottom.
Figure 22
5. The small straight top twig (3021) should be turned so the black flat
end is turned toward the rear. Slide the holes in the bottom of this
twig over the right peg on the left front log and the hole on the right
front log. See Figure 24.
6. The left top log (3019) should be positioned as shown in Figure 24.
Slide the holes in the bottom of this log over the hole in the left end of
the rear log and the peg in the left end of the left front log. The right
top log (3020) should be positioned as shown in Figure 24. Slide the
holes in the bottom of this log over the peg in the right end of the
right front log and rest it on the flat spot on the rear log.
7. Figure 25 shows the entire log set assembled. The volcanic stone
provided may be placed one high in front of the front burner tube
using care not to cover all the burner ports. Any extra embers may be
placed at the ends of the front log - off the burner. Place small pinches
of embers (rockwool) on top of the embers.
BRICK PANEL AND LOG SET INSTALLATION
Firebox Accessories / Parts
Cat. No. Description
H5862 Log Set
H5863 Bag of Embers (volcanic stone)
H5864 Bag of Rockwool (glowing embers)
H5865 Bag of Steel Wool
Log Set and Embers
Flat
Area
Left Top Log Right Top Log
Hole to
Cover
Hole to
Cover
Note: The pilot flame can be viewed
through this hole in the front log.
Embers
Note: The pilot flame can be viewed
through this hole in the front log.
Embers

20 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
* Thebreakersupplyingelectricitytothefireplacemustbeturnedoffatthe
electrical panel before any connections are made at the fireplace.
* The wire supplying the fireplace should be a minimum of 14 gage and
provide 120 Volts at 60 hz.
* The fireplace must be grounded in accordance with local electrical
codes or, in the absence of local codes, with the National Electrical
Code or ANSI/NFPA 70 - latest edition.
* The electrical box is located at the right rear of the fireplace (see
drawing below). Remove the cover, loosen the wire clamp A and feed
the household supply line through the clamp and retighten clamp.
* Connect the supply ground wire to the green screw B.
* Remove the wire nut C from the black wire coming from the fireplace
and join this wire to the black supply wire reusing the wire nut. Repeat
for white wire.
* Reinstall the electrical box cover.
* If a wall-mounted burner on/off switch or thermostat is to be used,
the wires running from the switch or thermostat should be routed to
the left side of the fireplace. The wire should be fed through the gas
line supply hole along the gas line to the valve.
Green (Ground)
Black (Hot)
White (Neutral)
Black
Black
Speed Control
Blower
From Power Source
Snap Switch (contacts close when fireplace is hot)
Fan Wiring Diagram
Wall-Mounted Fan Speed Control
If desired, a wall-mounted fan speed control can be installed. The breaker
suppling electricity to the fireplace must be turned off at the electrical
panel before any connections are made. The loop of wire with the label
attached (E above) may be cut and the wire leads from the wall-mounted
speed control connected to each end of the cut wire.
B
A
E
C
Figure 26
Figure 27
Figure 28
ELECTRICAL CONNECTIONS