Lenovo 6491 User manual

User Guide
Types 6491, 8013, 8702, 8706
Types 8716, 8970, 8972, 8976
Types 8980, 8982, 8986, 8992
Types 8994, 9266, 9276, 9278
Types 9282, 9286, 9288, 9374
Types 9378, 9380, 9384, 9628
Types 9632, 9647, 9649, 9695

User Guide

Note
Before using this information and the product it supports, be sure to read the “Important safety information” on page vand
Appendix B, “Notices,” on page 73.
Fourth Edition (February 2007)
©Copyright Lenovo 2006, 2007.
Portions ©Copyright International Business Machines Corporation 2005.
All rights reserved.
U.S. GOVERNMENT USERS –RESTRICTED RIGHTS: Our products and/or services are provided with
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule
contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in
Data-General, FAR 52.227.14 (Alternate III).

Contents
Important safety information ......v
Conditions that require immediate action .....v
General safety guidelines ..........vi
Service and upgrades ..........vi
Static electricity prevention ........ vii
Power cords and power adapters ...... vii
Voltage-selection switch ......... viii
Extension cords and related devices .....ix
Plugs and outlets ...........ix
External devices ............ix
Batteries ..............ix
Heat and product ventilation ........x
Operating environment .........xi
Electrical current safety information ......xi
Lithium battery notice........... xii
Modem safety information ......... xii
Laser compliance statement......... xiii
Power supply statement .......... xiii
Products with television tuner options installed .. xiii
Note to CATV system installer....... xiv
Example of antenna grounding ...... xiv
Data safety ..............xv
Cleaning and maintenance .........xv
Using headphones or earphones .......xv
Additional safety information ........ xvi
Introduction ............ xvii
Chapter 1. Arranging your workspace ..1
Comfort ................1
Glare and lighting ............1
Air circulation ..............2
Electrical outlets and cable lengths .......2
Chapter 2. Setting up your computer ..3
Installing the vertical stand .........3
Connecting your computer .........4
Turning on power ............10
Finishing the software installation .......10
Completing important tasks .........10
Updating your operating system .......11
Installing other operating systems .......11
Updating your antivirus software .......11
Shutting down the computer ........11
Chapter 3. Installing options .....13
Features ...............13
Available options ............16
Specifications ..............17
Supported operating positions ........18
Tools required .............18
Handling static-sensitive devices .......18
Installing external options .........19
Locating controls and connectors on the front of
your computer ............19
Locating connectors on the rear of your computer 20
Obtaining device drivers .........21
Removing the cover ...........22
Locating components ...........23
Accessing system board components ......24
Identifying parts on the system board .....25
Installing memory ............29
Installing PCI adapters ..........30
Installing internal drives ..........31
Drive specifications...........32
Installing adrive in bay 1........33
Installing adiskette drive in bay 3......34
Installing security features .........35
Integrated cable lock ..........36
Padlock...............37
Password protection ..........37
Changing the battery ...........37
Erasing alost or forgotten password (clearing
CMOS) ................38
Replacing the cover and connecting the cables...39
Chapter 4. Recovering software ....41
Creating and using the Product Recovery disc ...41
Performing backup and recovery operations ...42
Using the Rescue and Recovery workspace ....43
Creating and using rescue media .......44
Creating and using aRecovery Repair diskette ..45
Recovering or installing device drivers .....46
Setting arescue device in the startup sequence ..47
Solving recovery problems .........47
Chapter 5. Using the Setup Utility ...49
Starting the Setup Utility program.......49
Viewing and changing settings ........49
Using passwords ............49
Password considerations .........49
User Password ............50
Administrator Password .........50
Setting, changing, and deleting apassword...50
Using Security Profile by Device .......50
Selecting astartup device..........51
Selecting atemporary startup device .....51
Changing the startup device sequence ....51
Advanced settings ............52
Exiting from the Setup Utility program .....52
Chapter 6. Updating system programs 53
Using system programs ..........53
Updating (flashing) BIOS from adiskette ....53
Chapter 7. Troubleshooting and
diagnostics .............55
©Lenovo 2006, 2007. Portions ©IBM Corp. 2005. iii

Basic troubleshooting ...........55
Diagnostic programs ...........56
PC-Doctor for Windows .........57
PC-Doctor for DOS ...........57
PC-Doctor for Windows PE ........59
Cleaning the mouse ...........59
Optical mouse ............59
Non-optical mouse ...........59
Chapter 8. Getting information, help,
and service .............61
Information resources ...........61
Online Books folder ..........61
ThinkVantage Productivity Center ......61
Access Help .............62
Safety and warranty ..........62
www.lenovo.com ...........62
Help and service ............62
Using the documentation and diagnostic
programs ..............63
Calling for service ...........63
Using other services ..........64
Purchasing additional services .......64
Appendix A. Manual modem
commands .............65
Basic AT commands ...........65
Extended AT commands ..........67
MNP/V.42/V.42bis/V.44 commands ......68
Fax Class 1commands ..........69
Fax Class 2commands ..........69
Voice commands.............70
Appendix B. Notices .........73
Television output notice ..........74
Trademarks ..............74
Index ...............75
iv User Guide

Important safety information
Note
Please read important safety information first.
This information can help you safely use your desktop or notebook personal
computer. Follow and retain all information included with your computer. The
information in this document does not alter the terms of your purchase agreement
or the Lenovo
™ Limited Warranty. For more information, refer to the safety and
warranty information that is provided with your computer.
Customer safety is important. Our products are developed to be safe and effective.
However, personal computers are electronic devices. Power cords, power adapters,
and other features can create potential safety risks that can result in physical injury
or property damage, especially if misused. To reduce these risks, follow the
instructions included with your product, observe all warnings on the product and
in the operating instructions, and review the information included in this
document carefully. By carefully following the information contained in this
document and provided with your product, you can help protect yourself from
hazards and create asafer computer work environment.
Note: This information includes references to power adapters and batteries. In
addition to notebook computers, some products (such as speakers and
monitors) ship with external power adapters. If you have such aproduct,
this information applies to your product. In addition, computer products
contain acoin-sized internal battery that provides power to the system clock
even when the computer is unplugged, so the battery safety information
applies to all computer products.
Conditions that require immediate action
Products can become damaged due to misuse or neglect. Some product damage
is serious enough that the product should not be used again until it has been
inspected and, if necessary, repaired by an authorized servicer.
As with any electronic device, pay close attention to the product when it is
turned on. On very rare occasions, you might notice an odor or see apuff of
smoke or sparks vent from your product. Or you might hear sounds like
popping, cracking, or hissing. These conditions might merely mean that an
internal electronic component has failed in asafe and controlled manner. Or,
they might indicate apotential safety issue. However, do not take risks or
attempt to diagnose the situation yourself. Contact the Customer Support Center
for further guidance. For alist of Service and Support phone numbers, see refer
to the safety and warranty information that is provided with your computer.
Frequently inspect your computer and its components for damage, wear, or signs
of danger. If you have any question about the condition of acomponent, do not
use the product. Contact the Customer Support Center or the product
manufacturer for instructions on how to inspect the product and have it
repaired, if necessary.
©Lenovo 2006, 2007. Portions ©IBM Corp. 2005. v

In the unlikely event that you notice any of the following conditions, or if you
have any safety concerns with your product, stop using the product and unplug
it from the power source and telecommunication lines until you can speak to the
Customer Support Center for further guidance. See Chapter 8, “Getting
information, help, and service,” on page 61.
vPower cords, plugs, power adapters, extension cords, surge protectors, or power
supplies that are cracked, broken, or damaged.
vSigns of overheating, smoke, sparks, or fire.
vDamage to abattery (such as cracks, dents, or creases), discharge from abattery,
or abuildup of foreign substances on the battery.
vAcracking, hissing, or popping sound, or strong odor that comes from the
product.
vSigns that liquid has been spilled or an object has fallen onto the computer
product, the power cord, or power adapter.
vThe computer product, power cord, or power adapter has been exposed to
water.
vThe product has been dropped or damaged in any way.
vThe product does not operate normally when you follow the operating
instructions.
Note: If you notice these conditions with aproduct (such as an extension cord)
that is not manufactured for or by Lenovo, stop using that product until you
can contact the product manufacturer for further instructions, or until you
get asuitable replacement.
General safety guidelines
Always observe the following precautions to reduce the risk of injury and property
damage.
Service and upgrades
Do not attempt to service aproduct yourself unless instructed to do so by the
Customer Support Center or your documentation. Only use aservice provider who
is approved to repair your particular product.
Note: Some computer parts can be upgraded or replaced by the customer.
Upgrades typically are referred to as options. Replacement parts approved
for customer installation are referred to as Customer Replaceable Units, or
CRUs. Lenovo provides documentation with instructions when it is
appropriate for customers to install options or replace CRUs. You must
closely follow all instructions when installing or replacing parts. The Off
state of apower indicator does not necessarily mean that voltage levels
inside aproduct are zero. Before you remove the covers from aproduct
equipped with an ac power cord, always make sure that the power is turned
off and that the product is unplugged from any power source. For more
information on CRUs, refer to the User Guide for this product. If you have
any questions or concerns, contact the Customer Support Center.
Although there are no moving parts in your computer after the power cord has
been disconnected, the following warnings are required for your safety.
vi User Guide

Danger
Hazardous moving parts. Keep fingers and other body parts away.
Attention
Before replacing any CRUs, turn off the computer and wait three to five
minutes to let the computer cool before opening the cover.
Static electricity prevention
Static electricity, although harmless to you, can seriously damage computer
components and options. Improper handling of static-sensitive parts can cause
damage to the part. When you unpack an option or CRU, do not open the
static-protective package containing the part until the instructions direct you to
install it.
When you handle options or CRUs, or perform any work inside the computer, take
the following precautions to avoid static-electricity damage:
vLimit your movement. Movement can cause static electricity to build up around
you.
vAlways handle components carefully. Handle adapters, memory modules, and
other circuit boards by the edges. Never touch exposed circuitry.
vPrevent others from touching components.
vWhen you install astatic-sensitive option or CRU, touch the static-protective
package containing the part to ametal expansion-slot cover or other unpainted
metal surface on the computer for at least two seconds. This reduces static
electricity in the package and your body.
vWhen possible, remove the static-sensitive part from the static-protective
packaging and install the part without setting it down. When this is not
possible, place the static-protective packaging on asmooth, level surface and
place the part on it.
vDo not place the part on the computer cover or other metal surface.
Power cords and power adapters
Use only the power cords and power adapters supplied by the product
manufacturer.
Important safety information vii

The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G,
0.75 mm
2
,or better. For other countries, the suitable types shall be used
accordingly.
Never wrap apower cord around apower adapter or other object. Doing so can
stress the cord in ways that can cause the cord to fray, crack, or crimp. This can
present asafety hazard.
Always route power cords so that they will not be walked on, tripped over, or
pinched by objects.
Protect power cord and power adapters from liquids. For instance, do not leave
your power cord or power adapter near sinks, tubs, toilets, or on floors that are
cleaned with liquid cleansers. Liquids can cause ashort circuit, particularly if the
power cord or power adapter has been stressed by misuse. Liquids also can cause
gradual corrosion of power cord terminals and/or the connector terminals on a
power adapter, which can eventually result in overheating.
Always connect power cords and signal cables in the correct order and ensure that
all power cord connectors are securely and completely plugged into receptacles.
Do not use any power adapter that shows corrosion at the ac input pins or shows
signs of overheating (such as deformed plastic) at the ac input or anywhere on the
power adapter.
Do not use any power cords where the electrical contacts on either end show signs
of corrosion or overheating or where the power cord appears to have been
damaged in any way.
Voltage-selection switch
Some computers are equipped with avoltage-selection switch located near the
power-cord connection point on the computer. If your computer has a
voltage-selection switch, ensure that you set the switch to match the voltage
available at your electrical outlet. Setting the voltage-selection switch incorrectly
can cause permanent damage to the computer.
If your computer does not have avoltage-selection switch, your computer is
designed to operate only at the voltage provided in the country or region where
the computer was originally purchased.
If you relocate your computer to another country, be aware of the following:
vIf your computer does not have avoltage-selection switch, do not connect the
computer to an electrical outlet until you have verified that the voltage provided
is the same as it was in the country or region where the computer was originally
purchased.
vIf your computer has avoltage selection switch, do not connect the computer to
an electrical outlet until you have verified that the voltage-selection switch is set
to match the voltage provided in that country or region.
If you are not sure of the voltage provided at your electrical outlet, contact your
local electric company or refer to official Web sites or other literature for travelers
to the country or region where you are located.
viii User Guide

Extension cords and related devices
Ensure that extension cords, surge protectors, uninterruptible power supplies, and
power strips that you use are rated to handle the electrical requirements of the
product. Never overload these devices. If power strips are used, the load should
not exceed the power strip input rating. Consult an electrician for more
information if you have questions about power loads, power requirements, and
input ratings.
Plugs and outlets
If areceptacle (power outlet) that you intend to use with your computer
equipment appears to be damaged or corroded, do not use the outlet until it is
replaced by aqualified electrician.
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer
to obtain areplacement.
Do not share an electrical outlet with other home or commercial appliances that
draw large amounts of electricity; otherwise, unstable voltage might damage your
computer, data, or attached devices.
Some products are equipped with athree-pronged plug. This plug fits only into a
grounded electrical outlet. This is asafety feature. Do not defeat this safety feature
by trying to insert it into anon-grounded outlet. If you cannot insert the plug into
the outlet, contact an electrician for an approved outlet adapter or to replace the
outlet with one that enables this safety feature. Never overload an electrical outlet.
The overall system load should not exceed 80 percent of the branch circuit rating.
Consult an electrician for more information if you have questions about power
loads and branch circuit ratings.
Be sure that the power outlet you are using is properly wired, easily accessible,
and located close to the equipment. Do not fully extend power cords in away that
will stress the cords.
Be sure that the power outlet provides the correct voltage and current for the
product you are installing.
Carefully connect and disconnect the equipment from the electrical outlet.
External devices
Do not connect or disconnect any external device cables other than USB and 1394
cables while the computer power is on; otherwise, you might damage your
computer. To avoid possible damage to attached devices, wait at least five seconds
after the computer is shut down to disconnect external devices.
Batteries
All personal computers manufactured by Lenovo contain anon-rechargeable coin
cell battery to provide power to the system clock. In addition, many mobile
products, such as notebook computers, utilize arechargeable battery pack to
provide system power when in portable mode. Batteries supplied by Lenovo for
use with your product have been tested for compatibility and should only be
replaced with approved parts.
Important safety information ix

Never attempt to open or service any battery. Do not crush, puncture, or incinerate
batteries or short circuit the metal contacts. Do not expose the battery to water or
other liquids. Only recharge the battery pack strictly according to instructions
included in the product documentation.
Battery abuse or mishandling can cause the battery to overheat, which can cause
gasses or flame to “vent” from the battery pack or coin cell. If your battery is
damaged, or if you notice any discharge from your battery or the buildup of
foreign materials on the battery leads, stop using the battery and obtain a
replacement from the battery manufacturer.
Batteries can degrade when they are left unused for long periods of time. For some
rechargeable batteries (particularly Lithium Ion batteries), leaving abattery unused
in adischarged state could increase the risk of abattery short circuit, which could
shorten the life of the battery and can also pose asafety hazard. Do not let
rechargeable Lithium-Ion batteries completely discharge or store these batteries in a
discharged state.
Heat and product ventilation
Computers, AC adapters, and many accessories can generate heat when turned on
and when batteries are charging. Always follow these basic precautions:
vDo not leave your computer, AC adapter, or accessories in contact with your lap
or any part of your body for an extended period when the products are
functioning or when the battery is charging. Your computer, AC adapter, and
many accessories produce some heat during normal operation. Extended contact
with the body could cause discomfort or, potentially, askin burn.
vDo not charge the battery or operate your computer, AC adapter, or accessories
near flammable materials or in explosive environments.
vVentilation slots, fans, and heat sinks are provided with the product for safety,
comfort, and reliable operation. These features might inadvertently become
blocked by placing the product on abed, sofa, carpet, or other flexible surface.
Never block, cover, or disable these features.
Inspect your desktop computer for dust accumulation at least once every three
months. Before inspecting your computer, turn off the power and unplug the
computer’s power cord from the electrical outlet; then remove any dust from vents
and perforations in the bezel. If you notice external dust accumulation, then
examine and remove dust from the inside of the computer including heat sink inlet
fins, power supply vents, and fans. Always turn off and unplug the computer
before opening the cover. If possible, avoid operating your computer within 2feet
of high-traffic areas. If you must operate your computer in or near ahigh-traffic
area, inspect and, if necessary, clean your computer more frequently.
For your safety and to maintain optimum computer performance, always follow
these basic precautions with your desktop computer:
vKeep the cover closed whenever the computer is plugged in.
vRegularly inspect the outside of the computer for dust accumulation.
vRemove dust from vents and any perforations in the bezel. More frequent
cleanings might be required for computers in dusty or high-traffic areas.
vDo not restrict or block any ventilation openings.
vDo not store or operate your computer inside furniture, as this might increase
the risk of overheating.
vAirflow temperatures into the computer should not exceed 35° C(95° F).
xUser Guide

vDo not use non-desktop air filtration devices.
Operating environment
The optimal environment in which to use your computer is 10°C-35°C (50°F-95°F)
with humidity ranging between 35% and 80%. If your computer is stored or
transported in temperatures less than 10°C (50°F), allow the cold computer to rise
slowly to an optimal operating temperature of 10°C-35°C (50°F-95°F) before use.
This process could take two hours in extreme conditions. Failure to allow your
computer to rise to an optimal operating temperature before use could result in
irreparable damage to your computer.
If possible, place your computer in awell-ventilated and dry area without direct
exposure to sunshine.
Keep electrical appliances such as an electric fan, radio, high-powered speakers, air
conditioner, and microwave oven away from your computer because the strong
magnetic fields generated by these appliances can damage the monitor and data on
the hard disk drive.
Do not place any beverages on top of or beside the computer or other attached
devices. If liquid is spilled on or in the computer or an attached device, ashort
circuit or other damage might occur.
Do not eat or smoke over your keyboard. Particles that fall into your keyboard can
cause damage.
Electrical current safety information
Danger
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid ashock hazard:
vTo prevent possible shock hazard, do not use your computer during a
lightning storm.
vDo not connect or disconnect any cables or perform installation, maintenance,
or reconfiguration of this product during an electrical storm.
vConnect all power cords to aproperly wired and grounded electrical outlet.
vConnect to properly wired outlets any equipment that will be attached to this
product.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems, networks,
and modems before you open the device covers, unless instructed otherwise
in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
Important safety information xi

To connect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
To disconnect:
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Lithium battery notice
Caution
Danger of explosion if battery is incorrectly replaced.
When replacing the lithium coin cell battery, use only the same or an equivalent
type that is recommended by the manufacturer. The battery contains lithium and
can explode if not properly used, handled, or disposed of.
Do not:
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
The following statement applies to users in the state of California, U.S.A.
Perchlorate material: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
Modem safety information
Caution
To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.
To reduce the risk of fire, electrical shock, or injury when using telephone
equipment, always follow basic safety precautions, such as:
vNever install telephone wiring during alightning storm.
vNever install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
vNever touch uninsulated telephone wires or terminals unless the telephone line
has been disconnected at the network interface.
vUse caution when installing or modifying telephone lines.
vAvoid using atelephone (other than acordless type) during an electrical storm.
There may be aremote risk of electric shock from lightning.
vDo not use the telephone to report agas leak in the vicinity of the leak.
xii User Guide

Laser compliance statement
Some personal computer models are equipped from the factory with aCD or DVD
drive. CD and DVD drives are also sold separately as options. CD and DVD drives
are laser products. These drives are certified in the U.S. to conform to the
requirements of the Department of Health and Human Services 21 Code of Federal
Regulations (DHHS 21 CFR) Subchapter Jfor Class 1laser products. Elsewhere,
these drives are certified to conform to the requirements of the International
Electrotechnical Commission (IEC) 60825-1 and CENELEC EN 60 825-1 for Class 1
laser products.
When aCD or DVD drive is installed, note the following handling instructions.
Caution
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Do not remove the drive covers. Removing the covers of the CD or DVD drive
could result in exposure to hazardous laser radiation. There are no serviceable
parts inside the CD or DVD drive.
Some CD and DVD drives contain an embedded Class 3A or Class 3B laser diode.
Note the following statement.
Danger
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the beam.
Power supply statement
Never remove the cover on apower supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any component
that has this label attached. There are no serviceable parts inside these components.
If you suspect aproblem with one of these parts, contact aservice technician.
Products with television tuner options installed
The notice below applies to products containing television (TV) tuner devices that
connect to external antennas or to cable/CATV systems, or both, and that are
intended to be installed in North America. Users and installers in other countries
should follow local codes and ordinances when installing appliances that connect
to external antennas and cable/CATV systems. If local codes are not applicable, it
is recommended that users/installers follow guidelines similar to those that follow.
Important safety information xiii

Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to Article
820-40 of the National Electrical Code (NEC) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close as possible to the point of cable
entry as practical.
Example of antenna grounding
1 Ground clamp 5 Power service grounding electrode system (NEC
Article 250, Part H)
2 Antenna lead-in wire 6 Ground clamps
3 Antenna discharge unit (NEC
Section 810-20)
7 Electronic service equipment
4 Grounding conductors (NEC
Section 810-21
Figure 1. Proper grounding for the cable
xiv User Guide

The following notice applies to all countries and regions:
Danger
Outdoor antenna grounding
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded as to
provide some protection against voltage surges and built-up static
charges.
Lightning
For added protection for this equipment during alightning storm,
or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the video product due to
lightning and power line surges.
Power lines
An outside antenna system should not be located in the vicinity of
overhead power lines or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits,
as contact with them may be fatal.
Data safety
Do not delete unknown files or change the name of files or directories that were
not created by you; otherwise, your computer software might fail to work.
Be aware that accessing network resources can leave your computer vulnerable to
computer viruses, hackers, spyware, and other malicious activities that might
damage your computer, software, or data. It is your responsibility to ensure that
you have adequate protection in the form of firewalls, antivirus software, and
anti-spyware software and keep this software up to date.
Cleaning and maintenance
Keep your computer and workspace clean. Shut down the computer and then
disconnect the power cord before cleaning the computer. Do not spray any liquid
detergent directly on the computer or use any detergent containing flammable
material to clean the computer. Spray the detergent on asoft cloth and then wipe
the computer surfaces.
Using headphones or earphones
If your computer has both aheadphone connector and an audio-out connector,
always use the headphone connector for headphones (also called aheadset) or
earphones.
Excessive use of headphones or earphones for along period of time at high
volume can be dangerous if the headphones or earphones do not comply with
specifications of EN 50332-2. The headphone output connector of your computer
Important safety information xv

complies with EN 50332-2 Sub clause 5.1. This specification limits the computer’s
maximum wide band true RMS output voltage to 150mV. To help protect against
hearing loss, ensure that the headphones or earphones you use also comply with
EN 50332-2 (Sub clause 6.1) for awide band characteristic voltage of 75mV. Using
headphones that do not comply with EN 50332-2 can be dangerous due to
excessive sound pressure levels.
If your Lenovo computer came with headphones or earphones in the package, as a
set, the combination of the headphones or earphones and the computer already
complies with the specifications of EN 50332-1. If different headphones or
earphones are used, ensure that they comply with EN 50332-2. (Sub clause 6.1) for
awide band characteristic voltage of 75mV. Using headphones that do not comply
with EN 50332-2 can be dangerous due to excessive sound pressure levels.
Additional safety information
Plastic bags can be dangerous. Keep plastic bags away from babies and children to
avoid danger of suffocation.
xvi User Guide

Introduction
This User Guide contains the following information:
vChapter 1, “Arranging your workspace,” on page 1provides information about
setting up your computer for comfort and the impact of light sources, air
circulation, and electrical outlets.
vChapter 2, “Setting up your computer,” on page 3provides information about
setting up your computer and software and operating system installation.
vChapter 3, “Installing options,” on page 13 provides information on the features
and options that are available for your computer.
vChapter 4, “Recovering software,” on page 41 provides instructions on how to
use the ThinkVantage
® Rescue and Recovery ™ program to create product
recovery disks, back up data, recover software, and restore the entire contents of
your hard disk to apreviously saved state.
vChapter 5, “Using the Setup Utility,” on page 49 provides instructions on how to
view and change the configuration settings of your computer.
vChapter 6, “Updating system programs,” on page 53 provides information about
updating POST/BIOS and how to recover from aPOST/BIOS update failure.
vChapter 7, “Troubleshooting and diagnostics,” on page 55 provides information
about basic troubleshooting and diagnostic tools for your computer.
vChapter 8, “Getting information, help, and service,” on page 61 provides
information about the wide variety of helpful resources available from Lenovo.
vAppendix A, “Manual modem commands,” on page 65 provides commands for
manually programming your modem.
vAppendix B, “Notices,” on page 73 provides notices and trademark information.
©Lenovo 2006, 2007. Portions ©IBM Corp. 2005. xvii

xviii User Guide