Lenovo 46M4002 Product manual

1U C19 and C13 Switched and Monitored
PDUs
Installation and Maintenance Guide

Note: Before using this information and the product it supports read the general information in Appendix D
“Notices” on page 67; the safety information warranties and licenses information on the Lenovo Web site at:
https://support.lenovo.com/documents/LNVO-DOCS
Second Edition (October 2018)
© Copyright Lenovo 2015, 2018
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services
Administration “GSA” contract use reproduction or disclosure is subject to restrictions set forth in Contract No. GS-
35F-05925.

Contents
Safety . . . . . . . . . . . . . . . . . . . iii
Chapter 1 Introduction 1
Notices and statements in this document . . . . . . 1
Installation requirements . . . . . . . . . . . . 2
Inventory checklist. . . . . . . . . . . . . . . 2
Parts that come with all PDU models. . . . . . 2
Parts that come with the 1U PDU models . . . . 3
Features of the PDU . . . . . . . . . . . . . . 4
Hardware components . . . . . . . . . . . . . 5
Front view . . . . . . . . . . . . . . . . 5
Rear view . . . . . . . . . . . . . . . . 6
PDU load groups . . . . . . . . . . . . . . . 7
Load balancing . . . . . . . . . . . . . . . . 7
Chapter 2 Installing the 1U PDU
vertically in a rack cabinet 9
Installing the PDU in the side of a rack cabinet . . . 9
Installing the PDU in the side of an Enterprise rack
cabinet only . . . . . . . . . . . . . . . . 12
Chapter 3 Installing the 1U PDU
horizontally in a rack cabinet 17
Chapter 4 Cabling the PDU 23
Connecting to a console . . . . . . . . . . . 23
Connecting to a LAN . . . . . . . . . . . . . 24
Connecting to a PDU environment sensor . . . . 24
Connecting output devices . . . . . . . . . . 25
Chapter 5 Monitoring the power
status 27
Using the PDU Configuration Utility to set up the
PDU . . . . . . . . . . . . . . . . . . . 27
Power-on sequencing (some models) . . . . . . 31
Using HyperTerminal through the serial port . . 33
Using Telnet through the Ethernet port . . . . 35
Using SNMP through the Ethernet port . . . . 38
Using the web interface. . . . . . . . . . . . 39
Starting the web interface . . . . . . . . . 40
Power management relay setting . . . . . . 41
Environment status and configuration . . . . 41
Modifying the basic settings . . . . . . . . 42
Changing the network configuration . . . . . 46
Event and history log summaries . . . . . . 46
Chapter 6 Using the PDU
environment sensor 49
Features. . . . . . . . . . . . . . . . . . 49
Connecting the PDU environment sensor to the
PDU . . . . . . . . . . . . . . . . . . . 49
Chapter 7 Customer replaceable
unit parts 53
Chapter 8 PDU specifications 55
Appendix A Default PDU settings 59
Appendix B Behavior of the PDU
reset button 61
Appendix C Getting help and
technical assistance 63
Before you call . . . . . . . . . . . . . . . 63
Using the documentation . . . . . . . . . . . 64
Getting help and information from the World Wide
Web . . . . . . . . . . . . . . . . . . . 64
How to send DSA data . . . . . . . . . . . . 64
Creating a personalized support web page . . . . 64
Software service and support . . . . . . . . . 65
Hardware service and support . . . . . . . . . 65
Taiwan product service . . . . . . . . . . . . 65
Appendix D Notices 67
Trademarks . . . . . . . . . . . . . . . . 68
Important notes . . . . . . . . . . . . . . . 68
Recycling information . . . . . . . . . . . . 68
Particulate contamination . . . . . . . . . . . 69
Telecommunication regulatory statement. . . . . 69
Electronic emission notices . . . . . . . . . . 69
Federal Communications Commission (FCC)
statement . . . . . . . . . . . . . . . 70
Industry Canada Class A emission compliance
statement . . . . . . . . . . . . . . . 70
Avis de conformité à la réglementation
d'Industrie Canada. . . . . . . . . . . . 70
Australia and New Zealand Class A
statement . . . . . . . . . . . . . . . 70
European Union EMC Directive conformance
statement . . . . . . . . . . . . . . . 70
Germany Class A statement . . . . . . . . 70
Japanese electromagnetic compatibility
statements . . . . . . . . . . . . . . . 71
Korea Communications Commission (KCC)
statement . . . . . . . . . . . . . . . 72
Russia Electromagnetic Interference (EMI)
Class A statement . . . . . . . . . . . . 72
People's Republic of China Class A electronic
emission statement . . . . . . . . . . . 73
© Copyright Lenovo 2015 2018 i

Taiwan Class A compliance statement . . . . 73
Taiwan BSMI RoHS declaration. . . . . . . 74
Index 75
ii 1U C19 and C13 Switched and Monitored PDUs Installation and Maintenance Guide

Safety
Before installing this product read the Safety Information.
Antes de instalar este produto leia as Informações de Segurança.
Læs sikkerhedsforskrifterne før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto leggere le Informazioni sulla Sicurezza.

Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto leia as Informações sobre Segurança.
Antes de instalar este producto lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Each caution and danger statement in this documentation is labeled with a number. This number is used to
cross reference an English-language caution or danger statement with translated versions of the caution or
danger statement in the Safety Information document.
For example if a caution statement is labeled Statement 1 translations for that caution statement are in the
Safety Information document under Statement 1.
Be sure to read all caution and danger statements in this documentation before you perform the procedures.
Read any additional safety information that comes with your system or optional device before you install the
device.
Statement 1

DANGER
Electrical current from power, telephone, and communication cables is hazardous
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm
• Connect all power cords to a properly wired and grounded electrical outlet
• Connect to properly wired outlets any equipment that will be attached to this product
• When possible, use one hand only to connect or disconnect signal cables
• Never turn on any equipment when there is evidence of fire, water, or structural damage
• Disconnect the attached power cords, telecommunications systems, networks, and modems
before you open the device covers, unless instructed otherwise in the installation and
configuration procedures
• Connect and disconnect cables as described in the following table when installing, moving, or
opening covers on this product or attached devices
Table for Safety Statement 1 that explains the steps to connect and disconnect cables.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Statement 13
DANGER
Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain
conditions To avoid these hazards, ensure that your system electrical requirements do not exceed
branch circuit protection requirements Refer to the information that is provided with your device
for electrical specifications

Statement 14
CAUTION:
Hazardous voltage, current, and energy levels might be present Only a qualified service technician is
authorized to remove the covers where the following label is attached

Chapter 1 Introduction
The switched and monitored 1U PDU products enable you to connect up to nine C19 devices or up to 12
C13 devices (depending on the PDU model) and an additional three C13 peripheral devices to a single
dedicated power source. The PDUs have power monitoring capabilities.
The following PDU models are available:
• 46M4002 - 1U 9 C19 / 3 C13 Switched and Monitored DPI PDU (with removable power cord)
• 46M4003 - 1U 9 C19 / 3 C13 Switched and Monitored 60 A 3 Phase PDU (with attached power cord)
• 46M4004 - 1U 12 C13 Switched and Monitored DPI PDU (with removable power cord)
• 46M4005 - 1U 12 C13 Switched and Monitored 60 A 3 Phase PDU (with attached power cord)
The IBM Systems Director Active Energy Manager product can monitor and control the PDUs. Active Energy
Manager is an IBM Systems Director plug-in that measures and reports server power consumption as it
occurs. Active Energy Manager includes a feature to associate IBM Systems Director managed resources
with the power outlets on the PDUs. This enables you to know how much power each server is consuming
and which servers will be affected by any PDU outages. You can use the graphing capability of Active Energy
Manager to show a trending line for power that is being drawn by the outlets of the PDU models showing
which systems are connected to them.
Active Energy Manager also enables you to show a trending line for the temperature of the PDU and the
temperature that is measured by the environment sensor. In addition to monitoring Active Energy Manager
can control power of the individual outlets. From a central location Active Energy Manager can power off or
power on the outlets. This enables an administrator to prevent someone from connecting additional
equipment into unused outlets thereby making it easier to control power consumption within a rack. Active
Energy Manager can also shut down outlets in an emergency situation.
If firmware and documentation updates are available you can download them from the Lenovo website. The
PDU might have features that are not described in the documentation that comes with the PDU and the
documentation might be updated occasionally to include information about those features or technical
updates might be available to provide additional information that is not included in the PDU documentation.
To check for updates Go to http://www.lenovo.com/support.
Notices and statements in this document
The caution and danger statements in this document are also in the multilingual Safety Information
document which is on the Documentation CD. Each statement is numbered for reference to the
corresponding statement in your language in the Safety Information document.
The following notices and statements are used in this document:
• Note: These notices provide important tips guidance or advice.
• Important: These notices provide information or advice that might help you avoid inconvenient or
problem situations.
• Attention: These notices indicate potential damage to programs devices or data. An attention notice is
placed just before the instruction or situation in which damage might occur.
• Caution: These statements indicate situations that can be potentially hazardous to you. A caution
statement is placed just before the description of a potentially hazardous procedure step or situation.
© Copyright Lenovo 2015 2018 1

• Danger: These statements indicate situations that can be potentially lethal or extremely hazardous to you.
A danger statement is placed just before the description of a potentially lethal or extremely hazardous
procedure step or situation.
Installation requirements
You will need the following tools to install the PDU in a rack cabinet:
• One Phillips screwdriver
• One 10 mm (11/32 in.) wrench
• One cage-nut-insertion tool or flat-blade screwdriver (for installing cage nuts in some rack cabinets)
You can install a 1U PDU vertically in the side of a rack cabinet or horizontally within 1U1of EIA mounting
space in a rack cabinet.
• For vertical mounting instructions of the 1U PDU see Chapter 2 “Installing the 1U PDU vertically in a rack
cabinet” on page 9.
• For horizontal mounting instructions of the 1U PDU see Chapter 3 “Installing the 1U PDU horizontally in a
rack cabinet” on page 17.
Inventory checklist
Note: The illustrations in this document might differ slightly from your hardware.
Parts that come with all PDU models
The following parts come with all PDU models:
• One PDU environment sensor kit:
– One PDU environment sensor
– One Category 5 Ethernet cable
– One mounting screw
– Self-adhesive hook-and-loop fastener pad
• Miscellaneous hardware kit (for attaching the mounting brackets to the PDU and installing the PDU in a
rack cabinet)
21U C19 and C13 Switched and Monitored PDUs Installation and Maintenance Guide
1. One U is equal to 4.45 cm (1.75 in.)