Let's Go Aero Tentris TreeHaus User manual

QTY
1
1
2
2
2
2
2
2
8
1
1
1
1
8
1
DESCRIPTION
FABRIC BODY:
Tent body
POLES:
Main Tent Frame Pole with caps, Fiberglass, shock-corded - Gray
(for corner to corner, poles are the thickest)
Cross Ridge Pole with tips, Fiberglass, shock-corded – Green
(straight poles with metal end tips)
Bay Window Pole with bend & tips, Fiberglass, shock-corded - Gray
(pole with one bend in center, black rubber end caps)
Over Door Pole with cap, Fiberglass, shock-corded – Gray
(front and rear, straight pole with rubber end tips)
Door Window Pole with corner & tip, Fiberglass, shock-corded – Green
(pole with two bends, metal tips)
Inner Vestibule Pole with cap, Fiberglass, short – Gray
Aluminum Base Pole with bend & tips (Corner Tie-Ins) – Black
Tie-In Loop Straps with double grommet
Gear Loft
Pole Bag
Stake Bag
Guy Lines; 3.0M
Stake Set of eight 7 in. steel stakes
REV051920
TreeHaus Tent Manual
LittleGiant & SpecOps Camping Trailer Upfit
NAME
Tent
1 Tent bodyVelcro Expansion Strips
Rainfly
Main Tent Frame Pole
Cross Ridge Poles
Bay Window Pole
Over Door Pole
Door Window Pole
Inner Vestibule Pole
Aluminum Base Pole
Carry Bag
Review your parts list above to make sure all parts have been included in your package.
For assistance: Call Let’s Go Aero: 719-630-3800 or 877-464-2376 Mon-Fri 8:30-5:00 pm MST.
(Tie-ins)
ODPOL-356GY
ODPOL-356GY
DWPOL-120CR60OL
Bay Window Pole
(Green)
(Gray, 2 Bends)
(Shortest Pole)
(Gray, Straight)
(Green, 2 Bends)
(Gray, 1 Bend)
Cross Ridge Pole
Main Tent Frame Pole
Inner Vestibule Pole
Over Door Pole
Door Window Pole

WE ADVISE YOU TO ASSEMBLE THIS PRODUCT AT LEAST ONCE AT HOME BEFORE GOING ON A TRIP.
-
IMPORTANT NOTICE: You may compromise the original FIRE RETARDENCY and WATER REPELLENCY protective coatings when you apply sprays
or other chemical treatments to your tent. This fabric has been factory-treated and is HIGHLY WATER-REPELLANT; however, it is NOT WATER-
PROOF. All tents can experience seam leakage during wet weather. If you desire additional moisture protection, use a seam sealing compound
ONLY; be sure to follow the manufacturer’s directions.
Important: Prolonged exposure to sunlight that causes UV damage and/or the use of non-recommended foreign substances on synthetic material may
damage the fabric properties and IS NOT COVERED BY THE LIMITED WARRANTY.
REPAIRING A TEAR:
For small tears use a self-adhesive patch kit or polyurethane based sealer compound. We recommend a repair shop for larger tears.
Zipper Maintenance:
Nylon coil sippers are self-repairing. In the event of separation, move the slider to the beginning of the zipper tape and re-work zipper.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS PRODUCT FABRIC. THIS FABRIC IS NOT
FIREPROOF! It is made with flame resistant fabric, which meets CPAI-84 specifications. The application of any foreign
substance to the fabric may render the flame-resistant properties ineffective.
Do NOT ERECT NEAR an open flame. NEVER use any fuel burning. oxygen consuming devices, or any device that produces
fumes – including, but not limited to: cooking stoves, lanterns, candles, hibachis, or heaters – in or around your product.
Inhalation of fumes may result in carbon monoxide poisoning, injury and/or death.
This product is NOT machine washable or machine dryable.One of the easiest ways to damage your product is storing it
while wet. If you must close camp in the rain, follow these guidelines carefully:
• As Soon As Possible: Open the tent and ensure that every area of fabric is clean and completely dry before rolling up for storage.
• If necessary, hang the tent outside or loosely drape over a ladder in your garage or spare room for a few days, turning it inside and out to prevent
trapping pockets of water or debris.
• Use a soft brush to wipe away surface dirt.
To clean your product: Hand wash using a mild dishwashing soap and softbristle brush, then allow the fabric to completely air dry.
Don’t neglect the frame: Whip down all parts - steel, plastic, and fiberglass
- before putting away for next season’s use. Salts from ocean air can and do affect damage if not dealt with as quickly as possible.
Storing a wet fabric for as little as 24 hours in warm weather is likely to cause fabric to mildew. Once mildew sets in, the stains are permanent. Stains
cannot be removed without potential harm to the fabric’s coatings; chemicals or cleaning agents used to remove dirt and stains may irreversibly harm
the fabric.
Salts, mildew and other causes and subsequent effects are NOT covered under the limited warranty.
If your product does not work properly because of a defect in materials or workmanship, Let’s Go Aero Inc. will, for 1 Year from the
date of purchase, at its option either (a) repair our product with new or refurbished parts, or (b) replace it with a new product. The
decision to repair or replace will be made by Let’s Go Aero Incorporated. If repair is needed during the limited warranty period, the
purchaser will be required to furnish a sales receipt as proof of purchase indicating date of purchase, amount paid, and place of
purchase. Product will not be covered under warranty due to damages resulting from misuse, excessive or abusive usage, and/or
inclement weather conditions (i.e. windstorms, hurricanes, lightening stormes, tornadoes). In such events, the consumer assumes cost
of needed parts. Let’s Go Aero is not responsible for normal wear and tear, zipper exhaustion, or the natural breakdown in materials
that occurs with extended use.UNDER NO CIRCUMSTANCES SHALL LET’S GO AERO INC BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation may not apply to you.LET’S GO AERO INC EXPRESSLY EXCLUDES ALL WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states
do not allow the exclusion or limitation or implied warranties, so the above limitation may not apply to you.HOW TO OBTAIN WARRAN-
TY SERVICE: Call Let’s Go Aero at 719-630-3800 or 877-464-2376 during business hours. You must have a copy of your purchase
receipt from an authorized dealer (or Let’s Go Aero if purchased directly from us) as proof of purchase at time of call.
Limited 1 Year Warranty
Obtain a familiarity with the assembly and disassembly process to ensure preparadness should you find yourself setting up in the
dark or adverse weather conditions.

ASSEMBLY INSTRUCTIONS
THIS RECREATIONAL PRODUCT REQUIRES ADULT SUPERVISION TO ASSEMBLE.
* Carefully fold out your poles, make sure each pole segment is “seated” into the
* Do not drop tent pole bag. Do not bounce tent bag on its end to remove tent, as these actions may damage the shock-corded and/or
pole ends.
STEP 1: Verify Package Contents
Tip: Do this at home before you leave on your trip.
STEP 2: Attach Tent Fabric to Trailer
A) Attach Camper Deck Panels to both sides of Trailer.
Place both end gates in center section of trailer.
C)
B)
Open and spread out tent over camper decks and align doors in the right locations.
Start by velcroing each cornor of the decking first.
Extend Fiberglass poles and place in position ready for instllation. Sort by size and
colors.
STEP 3: Install Poles
A)
B) Main Tent Frame Poles and slide through black sleeves
located at the roof of the tent from corner to corner.
C) Slide the GREEN, Cross Ridge Poles through the corresponding sleeves at both front and rear of
tent. Insert the (metal) tip ends into the brass eyelets located on sleeve above side window
.
D) Slide the GRAY, center bent Bay Window Pole through the tan sleeve at side of tent. Repeat for remaining pole.
These poles have one (1) bend in center.
BWPL-311GY
Main Frame Tent Poles
-
Gray, Thickest, Rubber Tips
Cross Ridge Poles
-
Green, Straight, Metal Tips
Over Door Poles
DOOR
DOOR
-
Gray, Straight, Rubber Tips
Bay Window Poles
Grey, Center Bend, Rubber Tips
Apply Velcro Tent Expansion Strips to the front vertical sides of the trailer
TIP: Expansion strips are for optional use to provide added surface area for ease of
doorway zipper use. Strips may remain attached to tent for storage.

E) Slide the GRAY Over Door Pole through black sleeve over door. These poles are straight with
rubber end tips. Repeat for remaining pole.
Erect tent poles in the following order:
- Cross Ridge Poles (ensure they are engaged in their brass eyelets)
- Main Tent Poles
- Bay Window Poles and Over Door Poles
Insert rubber end tips of each pole into appropriate pole pockets located at respective corners.
F) Slide the GREEN Door Window Poles
through the sleeve. These poles have two
bends and metal tips. Insert tip ends into
brass eyelet located on either side of door.
Repeat for remaining pole.
G) To shape the Inner Vestibule Pole window
over door, insert into pole pockets directly
above door. Repeat for remaining pole.
H) After installing all poles adjust tent body to sit
securely on trailer and adjust velcro around
trailer base. Attach quick clips to all poles.
A)
areas and the green over the bay window sides.
B)
around tent poles.
STEP 5: Install the Gear Loft
STEP 4: Attach Rainfly
To install the Gear Loft, simply attach its S-Hooks to the fabric
loops inside tent ceiling.
TIP: Gear loft is for storing light weight items only.
STEP 6: Stake Guy Lines
To secure guy lines, locate guy line plastic slider and look for the portion of the
line opposite the knot. Pull this portion, forming a loop (works like a slip knot).
Extend guy line to ground and stake. Repeat with remaining guy lines.
Tip: Stakes provided are for solid ground. Camping in sand?
We suggest corkscrew style.
Raise Poles
Inner Vestibule Pole
Door Window Pole

Installation of Corner Base Pole Tie-Ins
SHORTER SECTION OF POLES UNDERNEATH DECKING
LONGER SECTION OF POLES OUTSIDE OF TENT
These Tie-Ins provide structural strength for enhanced high wind stability. The poles attach to both the tent and the
rainfly from underneath the trailer decking. Use as required for winds above 15 mph.
Take the black Aluminum
Base Poles for Tie-Ins and
observe there is a shorter and
longer section.Insert the tip end
of the short section in the hole
located underneath each
corner area of trailer deck.
Tent Tie-In Installation
Wrap the Tie-In Loop Straps with double grommet around Main Tent
Frame Pole. Insert the tip end of the longer section of pole into the brass
eyelet of strap. Repeat for all poles.
For Assistance, contact Let’s Go Aero at 877-464-2376 or 719-630-3800, or [email protected].
Visit our website at www.LetsGoAero.com
IMPORTANT NOTICE
Copyright© 2014, Lets Go Aero, Inc., All rights reserved.
CAUTION
The base poles are designed to maintain tension for structural reinforcement
during inclement weather. Be sure the pole tip fully engages with Tie In Loop
strap eyelets before releasing.