LevelOne FVT-2002 User manual

Copper to Fiber
Stand-Alone Media Converter
Quick Installation Guide
Model
No.
Description
FVT-2001
10/100BASE-TX to 100BASE-FX MMF SC
Converter, 2km
FVT-2002
10/100BASE-TX to 100BASE-FX MMF ST
Converter, 2km
FVT-2201
10/100BASE-TX to 100BASE-FX SMF SC
Converter, 20km
FVT-2401
10/100BASE-TX to 100BASE-FX SMF SC
Converter, 40km
GVT-2000
10/100/1000BASE-T to 1000BASE-X SFP
Converter
GVT-2001
10/100/1000BASE-T to 1000BASE-SX MMF SC
Converter, 550m
Ver. 1.3 - 1605

Table of Contents
1. INTRODUCTION...................................................1
1.1. FEATURES............................................................1
1.2. PACKAGE CONTENTS ...........................................2
2. HARDWARE DESCRIPTION ..............................3
2.1. FRONT PANEL......................................................3
2.2. REAR PANEL........................................................ 4
2.3. LED INDICATORS ................................................5
2.4. DIP-SWITCH......................................................... 7
3. CABLING ................................................................9
4. SPECIFICATION ................................................. 11
5. OPTIONAL SFP MODULES............................... 13

1
1. Introduction
LevelOne media converters are Fast Ethernet 10/100Base-TX to
100Base-FX and 10/100/1000Base-T to 1000Base-SX/LX
converters to provide the flexibility required in network integration.
The TX port auto-sense connection speed, auto-negotiates half/full
duplex modes and auto-selects MDIX media type. The fiber
connectors come with multimode or singlemode, SC, ST or SFP
connector to provide necessary connection interface and distance
capabilities.
LevelOne have designed 19” racks to organize media converters the
smart way by providing a single power supply. With the
Plug-and-play technology, the converter is easy to set-up and run.
For simple, cost-effective network design, LevelOne converter
series is the perfect solution to bridge the complex network
infrastructure.
1.1. Features
Fast Ethernet Module
Comply with IEEE 802.3, 802.3u and 802.3x standards.
Convert between UTP cabling and Fiber-optic cabling.
One RJ-45 connector, Auto-MDI/MDIX for UTP port.
Support 10/100 Mbps Auto-negotiation for UTP port.
Fiber cabling connectivity up to 40Km.
Store-and-forward switching to separate two collision domains.
One fiber connector (SC/ ST) for 100Base-FX.
6 DIP-switches to set the operation mode
Link- Lost-Forwarding function.

2
Gigabit Ethernet Module
Comply with IEEE 802.3, 802.3u and 802.3x, IEEE 802.3ab
1000BaseT, 802.3z 1000Base SX/LX standards.
Convert between UTP cabling and Fiber-optic cabling.
One RJ-45 connector, Auto-MDI/MDIX for UTP port.
Support 10/100/1000 Mbps Auto-negotiation for UTP port
Fiber cabling connectivity up to 80Km.
Store-and-forward switching to separate two collision domains.
One fiber connector (SC / SFP) for 1000Base-SX/LX
DIP-switches to set the operation mode function.
Link- Lost-Forwarding function.
1.2. Package Contents
- Stand-alone Media Converter
- Power Adapter (10/100M 5V,1A; 10/100/1000M 5V,2A)
- User Manual
Compare the contents of your converter module with the checklist
above. If any item is damaged or missing, please contact your local
dealer for service.

3
2. Hardware Description
2.1. Front Panel
FVT-2001 / FVT-2002 / FVT-2201 / FVT-2401
GVT-2000
GVT-2001
(1) RJ-45 Port (3) Fiber/SFP Connector
(2) LED Indicators (4) DIP-Switch
3
2
1
4

4
2.2. Rear Panel
Power Adapter: (10/100M DC 5V, 1A; 10/100/1000M DC 5V, 2A)
The rear panel contains a power socket. This power socket accepts
DC 5V voltage and minimum 1A & 2A supplied current.
4

5
2.3. LED Indicators
Fast Ethernet Module
LED
Status
Meaning
PWR
On
Power on
FX 100
On
100Mbps Fiber Speed
TX 100
On
100Mbps UTP Speed
OFF
10 Mbps UTP Speed
FDX
On
Converter works in the full duplex mode
OFF
Converter works in the half duplex mode
FX
LINK/ACT
On
Connection status display for fiber link.
“ON”indicates that Fiber link is in correct
connection.
Blinks
Active status display of fiber link
“Blink”indicates packet goes through FX end.
TX
LINK/ACT
On
Connection status display for electric link.
“ON”indicates that electric link is in correct
connection.
Blinks
Active status display of fiber link
“Blink”indicates packet goes through TX end

6
Gigabit Ethernet Module
LED
Status
Meaning
PWR
On
Power on
1000
On
1000Mbps UTP Speed
100
On
100Mbps UTP Speed
FDX
On
Converter works in the full duplex mode
Off
Converter works in the half duplex mode
LINK/ACT
(UTP)
Blinks
Active status display of electrical interface link
Blink” indicates packet goes through TP
LNK/ACT
(Fiber)
Blinks
Active status display of fiber interface link
“Blink” indicates packet goes through FX
Note: The UTP port speed is 10Mbps when both 100 and 1000 LED indicators
"OFF"

7
DIP-switch
The DIP-switch is used to configure operation mode for LLF (Link
Lost Forwarding) and operation mode for UTP/Fiber port. The
default value of DIPswitch is OFF.
Fast Ethernet Module
No
Status
Description
1
ON
LFP is Enable
OFF
LFP is Disable
2
ON
Modified cut-through switch mode is enable
OFF
Store and forward switch is enable
3
ON
force the TX port work 10/100Mbps,full/half
duplex
OFF
auto-negotiation mode is enable
4
ON
TX is 10Mbps
OFF
TX is 100Mbps
5
ON
TX is half duplex
OFF
TX is full duplex
6
ON
Normally close
Gigabit Ethernet Module
No
Status
Description
1
ON
LFP Enable
OFF
LFP Disable
Pin 2 Pin3
ON
OFF
ON
Pass through
Smart pass through
OFF
Modified cut through
Store and forward

8
Link Lost Forwarding:
When LLF is enable, allow UTP link failures to be reported to the
fiber side and also allow Fiber link failure to be reported to the UTP
side. Therefore, A link loss forward feature is provided in both UTP
and Fiber side.
Pure Converter mode (Gigabit Ethernet Module):
When pure converter mode is enabling (on), it operates with the
minimum latency. The transmission flow does not wait until entire
frame is ready, but instead it forwards the received data immediately
after the data being received. And TP port should be forced at1000M
in this application. When DIP-Switch is in Switch Converter mode
(off), the converter function is same as Switch Hub.
Note:
Please don’t change the DIP-switch setting when UTP or fiber port is
transmitting or receiving data. It may cause some data error.