LevelOne Infinity IEC-2002 User manual

IEC-2001
10/100/1000 Industrial Media Converter, SC MM 2KM, -40 to 75C
Quick Installation Guide
v1.00‐1209
IEC-2002 Page 1
Overview
LevelOne IEC-2002 is an industrial Gigabit Ethernet media converter
with a rugged aluminium case which providing superb heat
dissipation. This converter is designed to be mounted on an
industrial standard DIN-rail, plus the clearly visible status LEDs
provide simple monitoring of port link activity. It also features Link
Fault Pass Through in order to alert remote location when link
status changes
Fault Detection
Relay contact sends alert signal when the power failed or a port link
disconnected, therefore the system operator can respond quickly.
This relay contact can be easily configured with a simple DIP switch
High Reliability
All components are built to withstand harsh environment
applications without compromise where humidity, temperature
variation and even shock vibration are concerns, including Electric
& Utility, Critical Infrastructure, Transportation and Surveillance
Security. This device operates under -40 to 75 Celsius (-40 to 167
Fahrenheit) temperature.
Safety
Complies with NEMA (National Manufacturers Association) TS1 &
TS2 Environmental certified for the Traffic Control Equipment that
withstand extreme temperatures, operating voltage and humidity
fluctuation, vibration and shock commonly experienced in severe
outdoor environments.
IEC-2002 Page 2
Features
Complies with NEMA TS1 & TS2 Environmental requirements for
Traffic control equipment
Complies with IEC61000-6-2 EMC Generic standard immunity for
Industrial environment
Supports 1000SX Multimode SC fibre up to 2 kilometres
DIP switch configuration for "Link-Fault-Pass-Through," link
down alarm, speed, duplex mode
1000Mbps-Full/Half-duplex, Auto-Negotiation, Auto-MDI/MDIX
Full wire-speed forwarding rate
Alarms for power and port link failure by relay output
-40°C to 75°C (-40°F to 167°F) operating temperature range
IP30 aluminium case
Supports DIN-rail mounting installation
Package Contents
IEC-2002
Quick Installation Guide
IEC-2002 Page 3
LED Status
LED Status Description
PW 1,2,3
Steady Power On
Off Power Off
FAULT
Steady Redundant Power or Ports are failed
Off Redundant Power or Ports are normal
LNK/ACT
Steady Network connection is established
Flashing Transmitting or Receiving data
Off No connection occurred
FDX/COL
Steady Full duplex mode
Flashing Collision occurred
Off Half duplex mode
1000
Steady Connection at 1000Mbps speed
Off No connection
100
Steady Connection at 100Mbps speed
Off Connection at 10Mbps speed
LFPT
Steady LFPT is enabled
Off LFPT is disabled
LFPT: Link Forward Pass Through

IEC-2002 Page 4
Power Input
Terminal Block
Power1 12 – 48VDC (+), Power Ground (-)
Power2 12 – 48VDC (+), Power Ground (-)
Earth Ground
Relay Output (Fault)
*Relay warning signal disable for following:
1. The relay contact closes if Power1 and Power2 are both failed but Power3 on.
2. The relay contact closes if Power3 is failed but Power1 and Power2 are both
on.
DC Terminal Block Power
DC Terminal Block Power Inputs: There are two pairs of power
inputs can be used to power up this media converter.
Power3: DC JACK Power input 12VDC
IEC-2002 Page 5
DIP Switch
DIP 0 (Off) 1 (On)
1 Disable LFPT Enable LFPT
2 Disable link down alarm for copper port Enable link down alarm for copper port
3 Disable link down alarm for fibre port Enable link down alarm for fibre port
4 Enable Force mode for fibre port Enable Auto mode for fibre port
Note:
LFPT: Link Forward Pass Through
Disconnect the power before change the DIP switch settings
IEC-2002 Page 6
DIN Rail Mount
Assembly: Place the switch on the DIN rail from above using the
slot. Push the front of the switch toward the mounting surface
until it audibly snaps into place
Start-up: Connect the supply voltage to start up the switch via
the terminal block (or DC JACK)
Dismantling: Pull out the lower edge and then remove the switch
from the DIN rail.
IEC-2002 Page 7
1000Base-T Connector
Pin Label
1 TP0+
2 TP0-
3 TP1+
4 TP2+
5 TP2-
6 TP1-
7 TP3+
8 TP3-
1000Base-SX/LX
T
he Tx (transmit) port of device I is
connected to the Rx (receive) port
of device II, and the Rx (receive)
port of device I to the Tx (transmit)
port of device II.