LevelOne IGC-0101 User manual

1
User Manual
IGC-0101
RJ45 to SFP Gigabit Industrial Media Converter, 1 PoE Output
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that
may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 2004/108/EC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date. Please check with your local
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2017, All Rights Reserved.

2
Key Features
➢Hardened Industrial graded Marvell IC
➢Rugged design Aluminum enclosure 103.5x32x81.5mm (LxWxD)
➢Supports 30Watts PSE on TX port
➢Supports SFP fiber speed 100M or 1000M dual mode
➢Surge protection diodes on power input.
➢ESD protection diodes on RJ-45 port
➢Provides increased Noise Immunity
➢Working in extreme environment -40°C to 75°C
Introduction
This IGC-0101 Industrial POE media converter is equipped with Hardened Marvell IC
to provide a reliable power source to power up your remote POE device. It is designed
for Security, Transportation and Telco application to extend your network distances.
With its multi-purpose design, it can also be used for Din-Rail or wall-mounted. It is
an ideal unit for IP surveillance, traffic monitoring and Security application in critical
environment. It can tolerate -40°C to 75°C in harsh environment to perform a
reliable network.
Installation package
The following items are shipped with this device:
Din-Rail Mounted * 1
Wall-Mounted * 2
Screws * 4
4 pin Terminal Block * 1

3
Power connection
This unit provides 4 pin terminal block. It can be operated using 48-56VDC power
source. Always Make sure your input voltage is within this supported voltage
range. You need to use 56VDC input to generate IEEE802.3at 30Watts power.
To make power connection – Follow the printed polarity for V+, V- and RLY.
Connect positive wire to V+, connect negative wire to V- and also connect neutral
wire to ground.
+V- is for power input connection, this unit has only one power input.
RLY is for relay connection.
Connecting procedure:
STEP 1 –
Take out 4 pin terminal block located in the included mounting kit package.
STEP 2 –
Connect power wire to +V- with correct polarity. Connect RLY for relay.
STEP 3 –
Plug into terminal block socket shown above. Polarity needs to match the V+ and V-
WARNING -- Always SHUTS OFF power source to connect power wire.
WARNING -- Any exceeded input voltage will not make this unit function
and may damage this unit.
LED indicator
LED
Color
State
Description
PWR
Green
ON
Power is detected
OFF
Power is not detected
SFP Lnk/Act
Green
ON
FX port is detected
Flashing
FX data is transmitting/receiving
TX Lnk/Act
Green
ON
TX link is detected
Flashing
TX data is transmitting/receiving
TX PoE
Amber
ON
PSE is activated and PD is detected
OFF
PSE is detecting PD
+V1- RLY

4
Specification
IEEE Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE802.3x Flow Control and Back Pressure,
IEEE802.3af for POE
IEEE802.3at for POE+
Switch Architecture
Back-plane (Switching Fabric): 4Gbps
Data Processing
Store and Forward
Flow Control
IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame
9KB
MAC address Table Size
2K
Packet Buffer Size
1M
Network Connector
1 x RJ-45 10/100/1000BaseT(X) PSE with POE
Output power up to 30Watts
1 x 100/1000M SFP
Network Cable
UTP/STP Cat.5e or above Cable
EIA/TIA-568 10-ohm (100m)
Fiber Cable (Multi-mode):50/125um,62.5/125um
Fiber Cable (Single-mode): 9/125um
Protocol
CSMA/CD
LED
PWR (Green): ON－Power is detected
OFF－Power is not detected
SFP Lnk/Act (Green): ON－FX port is detected
Flashing－FX data is transmitting/receiving
RJ-45 port:
Lnk/Act (Green): ON－TX port is detected
Flashing－TX data is transmitting
PoE (Amber): ON－PSE is activated and PD is detected
Flashing－PSE is detecting PD
POE Pin Assignment
30 watts 2 pairs
V-, V-, V+, V+ for pin 1, 2, 3, 6
DIP Switch
DIP 1: Reserved
DIP 2: ON－SFP port 100M
OFF－SFP port 1000M (Default)
Reverse polarity protection
Present
Overload current protection
Present
Power Supply
4 pin terminal block with 48V-56V VDC Power Input,
RLY (Relay): Relay switch for alarm

5
Alarm Relay Contact
Relay outputs with current carrying capacity of 1 A
@24VDC,
Relay in short circuit mode when power fails. in open
circuit mode when power supply is connected
Power Consumption
2 W@48 VDC full load, Without POE
Max total power 36Watts at 56VDC
Removable Terminal Block
Provide 4 pin terminal block
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature
-40°C~75°C fully tested.
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40°C ~85°C
MTBF (mean time between
failure)
>500,000 hrs ( MIL-HDBK-217F) at 25°C
Housing
Rugged Aluminum, IP30 Protection
Case Dimension (L X W X D)
103.5 x 32 x 81.5 mm (L x W x D)
Installation mounting
DIN-Rail Mounting and Wall Mounting
Certifications
EN55022/24
ITE equipment
EN55011
Industrial, Scientific and Medical (ISM) equipment
Safety
IEC EN60950-1
EMC/EMS
CE, FCC, VCCI
EMI
FCC Part 15 Subpart B Class A,
CE EN 55022 Class A
EN 50155 / EN 60068-2-6
Vibration
EN 50155 / EN 60068-2-27
Shock
EN 50155 / EN 60068-2-32
Free Fall

6
Housing Dimension (mm)