LevelOne MDU-2400FXC User manual

-1-
MDU-2400FXC
4 Port 100Mbps SC Fiber Switch Module
MDU-2800TX
8 Port 10/100Mbps Fast Ethernet SwitchModule
MDU-2100SX
1000SX Gigabit Switch Module
Installation Guide

-2-
Introduction
MDU-2400FXC 4 Port 100Mbps SC Fiber Switch Module
There are two open slots (‘MODULE 1’ and ‘MODULE 2’) on the front panel of the Scalable
Ethernet Switch. The user canchoose to slide in up to two of the FX modules to increase the link
distance. This users guide describes the installation steps for the 4-Port 100Base-FX fiber
module. Also note that the module only works when incorporated with the base unit. For detailed
system level operation, please refer to the Users Manual.
MDU-2800TX 8Port 10/100Mbps Fast Ethernet Switch Module
There are two open slots (‘MODULE 1’ and ‘MODULE 2’) on the front panel of the Scalable
Ethernet Switch. The user can choose to slide in up to two of the modules to increase
10/100Mbps-port density. This users guide describes the installation steps for the 8-Port
100Base-TX module. Also note that the module only works when incorporated with the base
unit. For detailed system level operation, please refer to the Users Manual.
MDU-2100SX1000SX Gigabit Switch Module
There are two open slots (‘MODULE 1’ and ‘MODULE 2’) on the front panel of the Scalable
Ethernet Switch. The user can choose to slide in up to two of the modules to equip the system
with 1000Mbps-port capability. This users guide describes the installation steps of the 1-Port
1000Base-SX fiber module. Also note that the module only works when incorporated with the
base unit. For detailed system level operation, please refer to the Users Manual.

-3-
Installation
Please be sure the power of the system is down during the installation.Insertone ortwomodules
into the slots on the front panel of the switch (be sure the module is aligned within the guide-rails
and that the two fasteners on the front side of the module are tightened), as shown in the
following figure.
GSW-1600TXM with MDU-2400FXC
GSW-1600TXM with MDU-2800TX
GSW-1600TXM with MDU-2100SX
Note: For MDU-2100SX1000SX Gigabit Switch Module.The transmitter of the Fiber Optic
Transceiver is on the left-hand side (the one close to the Power LED) while the receiver is on the
right-hand side (the one close to the Link LED).
17 18 192021 22 23 24 100/10M
Full/Col
Link/Act
100/10M
Full/Col
Link/ActSystem
1Module1 1Module2
GSW-1600TXM 16 Port 10/100Mbps SNMP Switch
17 18 192021 22 23 24 100/10M
Full/Col
Link/Act
100/10M
Full/Col
Link/ActSystem
1Module1 1Module2
GSW-1600TXM 16 Port 10/100Mbps SNMP Switch
17 18 192021 22 23 24 100/10M
Full/Col
Link/Act
100/10M
Full/Col
Link/ActSystem
1Module1 1Module2
GSW-1600TXM 16 Port 10/100Mbps SNMP Switch

-4-
Status LEDs
MDU-2400FXC 4 Port 100Mbps SC Fiber Switch Module
Once the module(s) slides into the open slot(s) on the front panel of the switch, the LED
indicators for the module(s) will be shown in the LED Monitor area of the. The display includes
all the possible configurations. For instance, when the ‘MODULE 1’ slot is occupied, LED
columns 17 to 20 are used as indicators for the module. When the ‘MODULE 2’ slot is used,
LED columns 25 to 28 are the indicators. There are three LEDs for each port. Their definitions
are described as follows:
10/100Mbps LED
Off NotApplicable
Solid Green 100Mbps
Full/Col LED
Off Half Duplex operation (Default)
Solid Green Full Duplex operation
Blinking Amber Collisions detected for half Duplex operation.
Link/Act. LED
Off Port is link down.
Solid Green Port is link up and no traffic.
Blinking Green Port is link up and with traffic.

-5-
MDU-2800TX 8 Port 10/100Mbps Fast Ethernet Switch Module
Once the module(s) slides into the open slot(s) on the front panel of the switch, the LED
indicators for the module(s) will be shown in the LED Monitor area . The display includes all the
possible configurations. For instance, when the ‘MODULE 1’ slot is occupied, LED columns 17
to 24 are used as indicators for this module. When the ‘MODULE 2’ slot is used, LED
columns 25 to 32 are the indicators. There are three LEDs for each port. Their definitions that
described as follows:
10/100Mbps LED
Off 10Mbps (Default)
Solid Green 100Mbps
Full/Col LED
Off Half Duplex operation (Default)
Solid Green Full Duplex operation
Blinking Amber Collisions detected for half Duplex operation.
Link/Act. LED
Off Port is link down.
Solid Green Port is link up and no traffic.
Blinking Green Port is link up and with traffic.

-6-
MDU-2100SX 1000SX Gigabit Switch Module
Once the module(s) slides into the open slot(s) on the front panel of the switch, the LED
indicator for the module(s) will be shown on the module itself. Note also that, when the
‘MODULE 1’ slot is occupied, the port becomes Port 17 of the switch. When the ‘MODULE 2’
slot is used, the port becomes Port 25 of the switch. There are three LEDs for the 1000Mbps
port. Their definitions are described as follows:
Power LED
Off No power
Solid Green System is in operation.
Full/Col LED
Solid Green Full Duplex operation
Solid Yellow Half Duplex operation
Blinking Yellow Collisions detected for half Duplex operation.
Link/Act LED
Off Port is link down.
Solid Green Port is link up and no traffic.
Blinking Green Port is link up and with traffic.

-7-
Technical Specification
MDU-2400FXC 4 Port 100Mbps SC Fiber Switch Module
Standard
Interface
Environment
Dimension
EMI
IEEE802.3u, 100Base-FX
Fiber SC connector
Temperature:
Operating: 0°C to 40°C
Storage: -20°C to 70°C
Humidity:
Operating: 10%RH to 90%RH
Storage: 5%RH to 90%RH
145 x 116.8 x 25 mm (W x D x H)
5.7 x 4.6x 0.98 in
FCC, CE, VCCI Class A
MDU-2800TX 8 Port 10/100Mbps Fast Ethernet Switch Module
Standard
Interface
Environment
Dimension
EMI
IEEE802.3u, 100Base-TX
RJ-45 connector
Temperature:
Operating: 0°C to 40°C
Storage: -20°C to 70°C
Humidity:
Operating: 10%RH to 90%RH
Storage: 5%RH to 90%RH
145 x 116.8 x 25 mm (W x D x H)
5.7 x 4.6 x 0.98 in
FCC, CE, VCCI Class A
MDU-2100SX 1000SX Gigabit Switch Module
Standard
Interface
Environment
Dimension
EMI
IEEE802.3z, 1000Base-SX
Fiber SC connector
Temperature:
Operating: 0°C to 40°C
Storage: -20°C to 70°C
Humidity:
Operating: 10%RH to 90%RH
Storage: 5%RH to 90%RH
145 x 116.8 x 25 mm (W x D x H)
5.7 x 4.6 x 0.98 in
FCC, CE, VCCI Class A