LevelOne FSW-0809 User manual

LevelOne
FSW-0809
4+4 PoE Fast Ethernet Switch
User Manual
v1.0 - 0706

Safety
FCC Warning
This equipment has been tested and found to comply with
the regulations for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to
correct the interference at his or her own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
ii

Table of Content
INTRODUCTION ..............................................1
FEATURES.......................................................2
PACKAGE CONTENT .....................................3
HARDWARE DESCRIPTION...........................4
FRONT PANEL .................................................4
REAR PANEL...................................................4
LED INDICATORS.............................................6
System Power............................................6
PoE status (Port 1 ~ Port 4) ......................6
PoE MAX...................................................7
Ethernet port status (Ports 1~8)................7
POE RULE........................................................8
INSTALLATION..............................................10
TECHNICAL SPECIFICATIONS....................11
iii

Introduction
The FSW-0809 Switch integrates 100Mbps
Fast Ethernet and 10Mbps Ethernet network
capabilities in a highly flexible package. And
this switch’s Port-1 to Port-4 are Power over
Ethernet (PoE) ports, and it will automatically
detects the presence of IEEE 802.3af-compliant
powered device (PD) and provides power
through the Port-1 to Port-4. The switch
provides up to 15.4 W for PoE port and can be
used to WLAN access point, IP phone, video
camera and other PD devices. The Switch will
automatically detect the network appliance’s
requirements, and the switch will supplies the
required power current to each appliance.
Purpose
Power over Ethernet (PoE) integrates power
and data onto one single cabling infrastructure,
eliminating the need to have AC power
available at all locations. PoE is already widely
adopted in the market, saving up to 50% of
overall installation costs by eliminating the need
to install separate electrical wiring and power
outlets.
1

Features
8 ×10/100Mbps Auto-negotiation Fast
Ethernet RJ45 ports with 4-port PoE
function (port-1 ~ port-4)
Compliant with 802.3af specification
Supports PoE power up to 15.4W for PoE
port
Supports PoE power up to 30W for all PoE
ports
Supports PoE Powered Device (PD)
classification identify
Each port supports auto MDI/MDIX, so
there is no need to use cross-over cables or
an up-link port
Full/half duplex transfer mode for each port
Wire speed reception and transmission
Up to 1K unicast addresses entities per
device, self-learning, and table aging
96KBytes packet buffer
Supports IEEE 802.3x flow control for full-
duplex mode ports
Supports Back-pressure flow control for
half-duplex mode ports
2

Package Content
Open the shipping cartons of the Switch and
carefully unpacks its contents. The carton
should contain the following items:
– FSW-0809
– AC power adapter (Output: DC48V, 0.8A)
– Four rubber feet
– User Manual
If any item is found missing or damaged, please
contact your local reseller for replacement.
3

Hardware Description
This chapter describes the front panel, rear
panel, and LED indicators of the Switch.
Front Panel
LED Indicator:
Comprehensive LED indicators display the
status of the switch and the network (see the
LED Indicators chapter below).
Rear Panel
PoE Ports (Port 1~4):
These ports are PoE Enabled ports, the PoE
port will automatically activated when a
compatible terminal is identified, the Switch will
supply power through the Ethernet port to the
connected PoE device.
Note: The PoE ports will not offer the power to
the Legacy devices.
4

Ethernet Ports (Port 5~8):
These ports support network speeds of either
10Mbps or 100Mbps, and can operate in half-
and full- duplex transfer modes. These ports
also supports automatic MDI/MDIX crossover
detection function gives true “plug and play”
capability, just need to plug-in the network
cable to the hub directly and don’t care if the
end node is NIC (Network Interface Card) or
switch and hub
DC Power Jack:
Power is supplied through an external DC
power adapter. Check the technical
specification section for information about the
DC power input voltage.
Since the switch does not include a power
switch, plugging its power adapter into a power
outlet will immediately power it on.
5

LED Indicators
The front panel LEDs provides instant status
feedback, and, helps monitor and troubleshoot
when needed.
System Power
On :
When the Power LED lights on, the Switch
is receiving power.
Off :
When the Power turns off or the power cord
has improper connection.
PoE status (Port 1 ~ Port 4)
Green :
When the PoE powered device (PD) was
connected and the port supplies power
successfully.
Yellow :
When the PoE port have the following
failure happens:
PoE power circuit shortage
Power over current: over the power
current of PD’s classification
Out of PoE voltage of 44 ~ 57 VDC
output
Off : No PoE powered device (PD) connected.
6