Leviton ODD24-ID User manual

CAUTION
• For indoor applications only.
SAVE THESE INSTRUCTIONS.
Smart Wallbox Sensors: 24V with 0-10V Dimming Control
Cat. No. ODD24-ID
INSTALLATION INSTRUCTIONS ENGLISH
DI-000-ODD24-02A-X8
Before Installation
• Installs into standard single gang wall boxes.
• Supports multi-gang installations.
• Ivory, light almond, black, red, and gray faceplates are available with a color change kit
(sold separately).
• Decora®wallplate not included.
• Refer to wiring diagram of low voltage source (OPP20 / OSA20).
FOR OPTIMAL PERFORMANCE:
The ODD24-ID sensor lens establishes dozens of zones of detection. The sensor is
sensitive to the heat emitted by the human body. In order to trigger the sensor, the source
of heat must move from one zone of detection to another. The device is most effective in
sensing motion across its field of view, and less effective sensing motion towards or away
from its field of view. Keep this in mind when selecting the installation location. Note that
occupancy sensors respond to rapid changes in temperature, so care should be taken NOT
to mount the device near a climate control source (i.e., radiators, air exchanges, and air
conditioners). Hot or cold drafts will look like body motion to the device and will trigger it if
the unit is mounted too close. It is recommended to mount the occupancy sensor at least
6 ft away from a climate control source. In addition, it is also recommended NOT to mount
the occupancy sensor directly under a large light source. Large wattage bulbs (greater than
100W incandescent) give off a lot of heat and switching the bulb causes a temperature
change that can be detected by the device. Mount the occupancy sensor at least 6 ft away
from large bulbs. If it necessary to mount the device closer, lower the wattage of the bulb
directly overhead.
0-10V CONTROL WIRING INSTRUCTIONS
For 0-10V control wiring: connect the Violet wire to the + 0-10V line and the Gray wire
to the 0-10V common using Class 1 or Class 2 wiring methods as indicated in these
instructions, ballast/fixture/driver instructions or ballast/fixture/driver label markings.
Observe all requirements of any authority having jurisdiction with respect to wire type,
sleeving, isolation methods, and the like. Separation must be provided if Class 2 circuit is
installed together with Class 1, refer to NEC code for allowable methods and specifications.
FOR LIGHTING LOADS:
FOR LIGHTING AND PLUG LOAD CONTROL:
WARNINGS
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes
and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
1. Strip wires 3/4 in and connect as per wiring diagram. Ensure wires are firmly
attached and there is no exposed copper.
Product Description
Leviton Cat. No. ODD24-ID, wall switch and dimming Occupancy Sensor is designed
for use with a power pack (OPP20 or OSA20) or other Leviton low voltage (24V) source
and uses Passive Infrared (PIR) detection technology to monitor a room for occupancy
through a segmented lens. This specialized lens divides the field of view into sensor
zones. When a person passes into or out of a sensor zone, the sensor detects motion
and switches the lights ON. Lighting levels can be manually adjusted using the dimming
bar next to the switch. The lights will remain ON as long as there is an occupant moving
through the sensor zones. ODD24-ID can also be programmed to vacancy mode
(Manual ON/Auto OFF) for installations where Manual ON switching is required for Title
24 applications. The ODD24-ID provides a 180° field of view with a maximum coverage
area of approximately 1100 square feet. The maximum sensing distance in front of the
sensor is 30-40 feet, and 15-20 feet on either side. A “minor motion” zone detects small
body movements and allows the lights to stay ON even though a person may not be
moving or walking around the room. The remainder of the field of view, the “major motion”
zone, exhibits a lesser degree of sensitivity and requires larger movements. Simple
configuration can also be applied using push-button setup for several popular pre-
configured options. ODD24-ID is also equipped with a photocell for daylighting which is
programmable using the Leviton Smart Sensor App.
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit
breaker or fuse and test that power is off before wiring!
Installation
PUSH-BUTTON: ODD24-ID has a push-button switch that will toggle the lights ON or
OFF. When mode is set to Auto ON / Auto OFF, the lights will automatically turn ON
when occupancy is detected and will turn OFF automatically after occupancy is no longer
detected and the timeout has expired. If mode is set to Manual ON / Auto OFF, the lights will
only turn ON when the push button switch is pressed; the lights will turn OFF automatically
after occupancy is no longer detected and the timeout has expired. If the lights are ON, the
lights can be turned OFF when the button is pressed. The lights will stay OFF (regardless of
motion detected) until the timeout expires. After the timeout expires, the lights will turn ON
when the next motion is detected. This is useful for slide or film presentations. When using
a separate power pack for plug load control, the lights can be turned OFF and the plug load
receptacles will remain “live” until occupancy is no longer detected.
DIMMING BAR: The lights can manually be dimmed up or down by pressing the dimming
bar. To dim the lights down, press DOWN on the dimming bar and press UP to increase
the brightness.
NOTES:
• The Motion Indicator light will blink RED for 1 second each time motion is detected.
• In Manual On mode, the button must be pressed to turn the lights ON. In the absence of
motion, the unit will time out and turn the lights OFF.
Operation
Horizontal Beam Diagram
WIRING DIAGRAMS
Vertical Beam Diagram
2. Gently place the wires and your device into the wall box and attach with
screws provided.
3. If desired, change switch color. (Sold separately.)
4. Restore power and test ON/OFF operation. Locator light should be ON when switch is
in the OFF state.
5. Install Decora wallplate (not included).
6. ODD24-ID is designed to work and be fully functional right out of the box, settings can
be adjusted using the Leviton Smart Sensor App or simple push
button programming.
7. Using the Leviton Smart Sensor App or push button programming, you can now
configure the sensor to your preferred settings. (Leviton Smart Sensor App,
downloadable from Google Play™ or the Apple App Store®, using any Bluetooth™
enabled Android™ or iOS Device). Operating mode, sensor sensitivity, and sensor
timeout can be quickly adjusted. For more advanced settings such as daylighting and
nightlight configuration, the Leviton Smart Sensor App will need to be used for setup
and adjustments.
15-20 ft
4.6-6.1 m
10 ft
3 m
0
20 ft
6.1 m
30-40 ft
9.1-12.2m
10 ft
3 m
15-20 ft
4.6-6.1 m
40-48 ft
12.2-14.6 m
20 ft
6.1 m
30-40 ft
9.1-12.2m
Major motion coverage
1100 ft^2 (102m^2)
Minor motion coverage
400 ft^2 (37.2m^2)
Violet
Gray
+
+
Blue (not connected)
Power Pack
Green
Ground
Red
Black
Orange
Occupancy
Dimming
Lighting
Load
0-10V
24V
Violet
Gray
+
+
Blue
Power Pack
Green
Ground
Red
Black
Orange
Occupancy
Dimming
Lighting
Load
0-10V
24V
To Lighting Load
Black (Line)
White(Neutral)
Blue (Line)
Blue (Load)
+
Power Pack
Occupancy
24V
To Plug Load
Black (Line)
White(Neutral)
Blue (Line)
Blue (Load)
PIR Lens and
Nightlight
Dimming Level
Indicator
Programming:
can be performed
by pressing button
(per install instructions)
Photocell and
Locator Light
ON/OFF
Button
Dimming Bar
Motion Indicator
Light
Configuration and Programming
1. The ODD24-ID Sensor is designed to work out of the box in default settings. Changes
to these settings and additional product configuration can be performed using the
Leviton Smart Sensor App, downloadable from Google Play™or the Apple App Store®,
using any Bluetooth™enabled Android™or iOS Device.
a. To pair to device using the Leviton Smart Sensor App:
i. Press and hold the ON/OFF button for 2-5 seconds; when the light behind the
PIR lens blinks BLUE, release the button.
ii. Open the Leviton Smart Sensor App and connect to the device.
iii. The device can also be found by scanning for nearby devices; devices can be
identified in the app to confirm you are connected to the right sensor.
b. Use the Leviton Smart Sensor App to:
i. Set operating mode to Auto ON / Auto OFF (default) or Manual ON / Auto OFF.
ii. Adjust the sensitivity of the sensor to increase or decrease Field of view
coverage area pending the room size (100% for larger spaces approaching
1100 sq ft).
iii. Adjust timeouts (amount of time lights/load will turn OFF after occupancy is no
longer detected).
iv. Activate the night light and its operating mode; selection of custom night
light color.
v. Dimming configuration including partial ON and partial OFF levels and timeouts.
vi. Add daylighting and select target levels for daylighting.
vii. Set a security code to lock configuration.
viii. See Leviton Smart Sensor App for additional settings and other
programming options.
2. If the installer does not have access to a Bluetooth enabled Android or iOS Device,
popular preset product configuration can also be made using simple push
button commands:
a. If wall plate is attached, remove first. With the wallplate removed, pinch sides of
sensor near bottom tabs to release front cover of sensor.

© 2020 Leviton Mfg. Co., Inc.
SPECIFICATIONS
Input Voltage/Frequency 12-24VDC
Input Current
24V 0.02A
120-277V N/A
Load Ratings
LED, CFL, Electronic Ballast @ 120V N/A
LED, CFL, Electronic Ballast @ 277V N/A
Magnetic Ballast @ 120V N/A
Magnetic Ballast @ 277V N/A
Resistive, Tungsten @ 120V N/A
Resistive, Tungsten @ 277V N/A
Motor @ 120V N/A
Motor @ 277V N/A
IP Rating IP10
Network Connections BLE 4.2, BLE 5.0
Operating Temperature 0°C - 40°C (32°F - 104°F)
Storage Temperature -40°C to 85°C (-40°F - 185°F)
Purpose of Control Energy Management Equipment
Action Control Type 1
Pollution Degree 2
Impulse Voltage 4000V
NOTES:
• Use the number of light blinks to determine which user mode the sensor is set to.
If pressed more than 8 times, it will cycle back to the start of the list.
• Auto ON/Auto OFF (10 min timeout and 1 button press) is the DEFAULT MODE.
3. Daylighting and Night Light: The ODD24-ID is equipped with a photocell for
daylighting and also has a built in night light that can be turned ON and configured
using the Leviton Smart Sensor App.
4. Bluetooth Reset: Resets any security settings but preserves lighting and mode settings.
a. Push button on switch for approximately 20-25 seconds until the locator light
is flashing RED.
NOTE: After 5 seconds, light behind PIR lens will blink BLUE and then alternate
between BLUE and RED; at 10-15 seconds will then blink GREEN.
b. When the light flashes RED, release the button.
c. The device will reset and turn off when complete.
d. When device turns back on it will have no password set.
DI-000-ODD24-02A-X8
For Technical Assistance Call: 1-800-824-3005 (U.S. Only) or 1-800-405-5320 (Canada Only) www.leviton.com
Troubleshooting
• If sensor does not trigger when entering the room or space, increase the sensitivity level
of the sensor and/or check the daylighting settings (increase the daylighting level).
• If the lights constantly stay ON even when room is unoccupied:
- Check the Time Out setting and confirm set to desired time.
- Try lowering the sensor sensitivity; if problem persists, try lowering again.
- Check for reflected heat/motion as sensor may be seeing motion through a window.
- Check for adjacent HVAC and/or heater ducts.
Button
Press
Locator
Light Blinks Operating Mode Sensor Sensitivity Timeout
Daylighting
and
Night Light
1
*Default
operation
1 Auto ON / Auto OFF 75% 10mins OFF & OFF
2 2 Auto ON / Auto OFF 75% 20mins OFF & OFF
3 3 Auto ON / Auto OFF 100% 10mins OFF & OFF
4 4 Auto ON / Auto OFF 100% 20mins OFF & OFF
5 5 Manual ON / Auto OFF 75% 10mins OFF & OFF
6 6 Manual ON / Auto OFF 75% 20mins OFF & OFF
7 7 Manual ON / Auto OFF 100% 10mins OFF & OFF
8 8 Manual ON / Auto OFF 100% 20mins OFF & OFF
INDICATOR LIGHT DESCRIPTIONS
LED Location Action / Definition
RED Behind PIR Lens Blinks ON for 1 second upon
PIR detection
RED Behind PIR Lens
Blinking RED: Device in Bluetooth
reset; continues until reset is complete
then stops
BLUE Behind PIR Lens Blinking BLUE LED: Device BLE in
Pairing Mode
BLUE / RED Behind PIR Lens Alternating BLUE/RED: Device in
Installation/Test Mode (Factory Only)
GREEN Behind PIR Lens
and Locator
GREEN light behind PIR lens / Locator
LED blinking according to Menu Mode:
Device is in Manual Configuration
mode, number of LED blinks shows
which mode device is in
GREEN ALL Blinking GREEN LEDs indicates device
is in identify mode
GREEN / BLUE Behind PIR Lens Alternating GREEN/BLUE during 1
minute Daylight Calibration
GREEN / BLUE Behind PIR Lens
GREEN/BLUE blinks for 2 seconds
every 30 seconds when Daylighting
is active
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd,
Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.
FCC COMPLIANCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
STATEMENT CAUTION
Changes or modifications not expressly approved by Leviton Manufacturing Co., could void the user’s authority to operate the equipment.
FCC SUPPLIERS DECLARATION OF CONFORMITY
Smart Wallbox Sensors manufactured by Leviton Manufacturing, Inc., 201 N Service Road, Melville, NY, http://www.Leviton.com. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF EXPOSURE AND CO-LOCATION:
To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population / uncontrolled exposure this device should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the
radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and
proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty
excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a
particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Trademark Disclaimer
The Leviton logo and Decora are registered trademarks of Leviton Manufacturing Co., Inc. Google Play and Android are trademarks of Google, LLC. The Apple App Store is a registered trademark of Apple, Inc. Bluetooth
is a trademark of Bluetooth SIG, Inc. Use herein of other third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their
respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement. No part of this document may be reproduced, transmitted or transcribed without the express written permission
of Leviton Manufacturing Co., Inc.
b. With the front faceplate of the sensor removed, push both buttons on front of sensor
simultaneously for 10-15 seconds (note: after 5 seconds, a light will blink BLUE
and then alternate between BLUE and RED) and release when the Locator Light is
blinking GREEN.
Locator Light
Top Button
Bottom Button
c. Push the bottom button to move to the next automatic setting using the table below
as a guide.
d. When at the desired setting, press and hold the bottom button again for 5 seconds
(until the GREEN LOCATOR light turns ON), when the button is released, the light will
flash the number of times as the setting selected; the sensor is now saved in
that configuration.
e. The front cover can now be reattached. Insert the top tabs and push in bottom tabs
to attach.