Leviton 57A00-1 User manual

Vanishing Door/Window Transmitter
Cat. No. 57A00-1
Installation Instructions
DI-021-SY471-05A
(57I00-1)
WARNINGS AND CAUTIONS
• Read and understand all instructions. Follow all warnings
and instructions marked on the product.
• Do not use this product near water - e.g., near a tub, wash
basin, kitchen sink or laundry tub, in a wet basement, or near
a swimming pool.
• Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
• Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in  re.
• SAVE THESE INSTRUCTIONS.
Notice for users in California - CR Coin Cell Lithium Battery
information: This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material – special handling
may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Description
The 57A00-1 Vanishing Door/Window Transmitter is a
supervised wireless contact that works with the Leviton
45A00-1 Wireless Receiver. It has beveled edges that vanishes
into any décor. It also features a bypass button that allows
you to manually bypass the transmitter, which automatically
restores when the magnet is replaced.
Installing the Battery
The 57A00-1 requires one CR2032 lithium battery. To install the
battery, remove the cover as indicated in Figure A.
Once cover is removed, insert the battery with the positive (+)
side up as indicated in Figure B.
Locate Transmitter
Select the location where the 57A00-1 is to be mounted.
NOTE: RF signals can be affected by metal objects, including
metal doors or large mirrors. Such locations should be avoided
as they can interfere with proper operation.
Mounting the 57A00-1
Once you have determined the proper location, the 57A00-1
can be permanently mounted using the supplied adhesive tape.
NOTE: It is the responsibility of the installer to ensure that the
57A00-1 is securely mounted in the intended location.
Using Adhesive Tape
Ensure that the surface is clean and dry. Apply the supplied
tape to the back of the 57A00-1, press and hold  rmly in the
desired location for approximately 10-15 seconds. It can
take up to 24 hours for the tape to reach maximum bonding
strength.
Mounting the Magnet
Align the magnet with the 3 notches on the 57A00-1 housing.
Mount the magnet a maximum of .4” from the 57A00-1 by using
the supplied tape.
Enrolling the 57A00-1
To enroll the 57A00-1, put the 45A00-1 Wireless Receiver
into Setup mode and advance to an unused address
location. Activate the reed switch by removing the magnet
from the transmitter for 1 second, then replacing it. Refer
to the Installation Instructions for the 45A00-1 for additional
information.
Using the Bypass Button
To temporarily bypass the transmitter so that you can open
an armed door or window without causing an alarm, press the
center of the transmitter and hold for 5 seconds. Once you
remove your  nger, you will notice that the LED behind the
transmitter’s front panel will begin to blink.
While the LED is blinking, the transmitter will not transmit any
signals to the receiver (you may open the door or window while
the LED is blinking without causing an alarm).
To remove cover, insert
screwdriver here, and gently twist
+
To remove battery, insert
screwdriver here, and twist
Battery (+ side up) PC Board
Tamper Switch
Figure A
Figure B
WEB VERSION

LEVITON LIMITED WARRANTY
Leviton warrants to the original consumer purchaser and not
for the benet of anyone else that products manufactured
by Leviton under the Leviton brand name (“Product”) will be
free from defects in material and workmanship for the time
periods indicated below, whichever is shorter: • OmniPro
II and Lumina Pro: three (3) years from installation or 42
months from manufacture date. • OmniLT, Omni IIe, and
Lumina: two (2) years from installation or 30 months from
manufacture date. • Thermostats, Accessories: two (2)
years from installation or 30 months from manufacture date. •
Batteries: Rechargeable batteries in products are warranted
for ninety (90) days from date of purchase. Note: Primary
(non-rechargeable) batteries shipped in products are not
warranted. Products with Windows® Operating Systems:
During the warranty period, Leviton will restore corrupted
operating systems to factory default at no charge, provided
that the product has been used as originally intended.
Installation of non-Leviton software or modication of the
operating system voids this warranty. Leviton’s obligation
under this Limited Warranty is limited to the repair or
replacement, at Leviton’s option, of Product that fails due
to defect in material or workmanship. Leviton reserves the
right to replace product under this Limited Warranty with new
or remanufactured product. Leviton will not be responsible
for labor costs of removal or reinstallation of Product.
The repaired or replaced product is then warranted under
the terms of this Limited Warranty for the remainder of the
Limited Warranty time period or ninety (90) days, whichever
is longer. This Limited Warranty does not cover PC-based
software products. Leviton is not responsible for conditions
or applications beyond Leviton’s control. Leviton is not
responsible for issues related to improper installation,
including failure to follow written Installation and operation
instructions, normal wear and tear, catastrophe, fault or
negligence of the user or other problems external to the
Product. To view complete warranty and instructions for
returning product, please visit us at www.leviton.com.
Copyright and Trademark Information
This document and all its contents herein are subject to and
protected by international copyright and other intellectual
property rights and are the property of Leviton Manufacturing
Co., Inc, its subsidiaries, afliates and/or licensors. © 2013
Leviton Manufacturing Co., Inc. All rights reserved.
Use herein of third party trademarks, service marks,
trade names, brand names and/or product names are for
informational purposes only, are/may be the trademarks of their
respective owners; such use is not meant to imply afliation,
sponsorship, or endorsement.
No part of this document may be reproduced, transmitted or
transcribed without the express written permission of Leviton
Manufacturing Co., Inc.
For Technical Assistance Call: 800-824-3005 - www.leviton.com
DI-021-SY471-05A (57I00-1)
FOR CANADA ONLY
For warranty information and/or product returns, residents
of Canada should contact Leviton in writing at Leviton
Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire
(Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
© 2013 Leviton Mfg. Co., Inc.
Once the LED stops blinking, the next time the magnet is
removed from the transmitter (i.e. the door or window is
opened), the signal will be transmitted to the receiver.
Notes:
1. When activated, the LED will blink for approximately 7
seconds.
2. If the door or window is open when the LED stops blinking,
once the door or window is closed, the transmitter is
restored. The next time the door or window is opened, the
signal is transmitted.
Tamper Switch
Out of the box the 57A00-1 comes equipped with cover tamper
detection. If the cover is removed, the 57A00-1 will report a
zone tamper (cover off) to the receiver.
WEB VERSION