Lex System SHARK series User manual

SHARK Waterproof
Assembly Guide
Panel PC
Box PC
6G0000-0000-0000

WARNING !
SHARK Waterproof Assembly guide ......................................
SHARK Waterproof BOX PC Exploded Drawing ...................
SHARK Waterproof Panel PC Exploded Drawing ..................
IP (International Protection)
1
4
7
code- Levels of Protection ....................................................... 10
Introduction of necessary tools ..............................................
IP66 Packing list .......................................................................
IP67 Packing list .......................................................................
Difference of Waterproof cables ..............................................
I/O Connector Pinouts ..............................................................
13
14
15
16
17
Contents

WARNING !
1. Please do not remove the caps of waterproof cables unless needed.
2. Waterproof cables must be fastened tightly on the connectors of system.
3. Waterproof cables must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
4. Please align the screw to the system when fasten it.
Crooked angle should be avoided.
5. Align the screws and fasten them diagonally, just loosely.
Tighten them until make sure all screws are enable to be
fastened correctly to the end.
6. All top cover screws must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
7. If the system error occurred, please turn the power off and unplug it from the
power supply before removing system from the water.
8. Please do not unfasten any screw unless the system is clean and
completely dry.
9. Please be aware that even one drop of water might carry a risk of
damage to the waterproof connectors, make sure to avoid when
removing waterproof cables.
10. To avoid causing any damage to the waterproof connectors,
using the standard tools are requested.

1
1. Unscrew ten (M2.5*4) screws from the
bottom cover and then lift the cover out
of the system. (Fig.1)
3. Install the mSATA into the connector
slot at a 45 degree angle. (Fig.3)
2. Unscrew the(M2*6) screw from the screw
thread on motherboard. (Fig.2)
4. Push the mSATA down to the motherboard
Fasten mSATA with the (M2*6) screw.
(Fig.4)
(Fig.1)
(Fig.3)
(Fig.2)
45°
(Fig.4)
SHARK Waterproof Assembly guide

2
8. Connect the SATA DATA cable
with motherboard. (Fig.8)
10. Screw the HDD KIT back to the system
with four (M3*4) screws. (Fig.10)
5. Fasten the HDD on HDD KIT with
four (M3*4) screws. (Fig.5)
9. Connect the SATA Power cable
with motherboard. (Fig.9)
6. Connect the SATA DATA cable
with HDD(Fig.6)
(Fig.5)
(Fig.7)
(Fig.9)
(Fig.6)
(Fig.8)
(Fig.10)
7. Connect the SATA Power cable with HDD.
(Fig.7)

3
12. Screw the bottom cover back to the
system with then (M2.5*4) screws.
(Fig.12)
14. Plug in the waterproof cables. (Fig.14)
11. Attach the thermal pad on the HDD
and avoid the heat-dissipating holes at
the same time. (Fig.11)
13. Remove the waterproof caps. (Fig.13)
(Fig.11)
(Fig.13)
(Fig.12)
(Fig.14)

4
SHARK Waterproof BOX PC Exploded Drawing
7" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1Front Bezel 16HDD 1
2Back Cover 17Key Pad 1
3Front Cover 18Waterproof Cable 7
4O-ring 292I Mainboard 1
5HDD brackrt 1
2
7
1
6
5
3
9
4
8

5
1
9
2
3
2
4
7
5
8
6
11
10
SHARK Waterproof BOX PC Exploded Drawing
10.1" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1SHARK 10.1"(WP),BOX,TOP
COVER,LF,AL 6063,Black,For 3I/2I 17M12 CABLE WP x
2SHARK 10.1,O-RING FOR FRONT
BEZEL,L=795MM,Black 282.5" HDD 1
3SHARK 10.1"(WP),BOX,FRONT
BEZEL,LF,AL 6063,Black 192I Mainboard 1
4SHARK 10.1"(WP),BOX,BOTTOM
COVER,LF,AL 6063,Black 110BATTERY 2S1P 3360mah 1
5SHARK 10.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black x11
SHARK 10.1" BOX PC,Battery
Bracket,FOR 2S1P 3360mah 1
6STAR 10.4",HDD
RACKET,LF,SECC=1.0,MATERIAL 1

6
1
9
2
6
8
5
3
7
2
4
SHARK Waterproof BOX PC Exploded Drawing
10.1" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1SHARK 10.1"(WP),BOX,TOP
COVER,LF,AL 6063,Black,For 3I/2I 16
STAR 10.4",HDD
RACKET,LF,SECC=1.0,MATERIAL 1
2SHARK 10.1,O-RING FOR FRONT
BEZEL,L=795MM,Black 27M12 CABLE WP x
3SHARK 10.1"(WP),BOX,FRONT
BEZEL,LF,AL 6063,Black 182.5" HDD 1
4SHARK 10.1"(WP),BOX,BOTTOM
COVER,LF,AL 6063,Black 193I Mainboard 1
5SHARK 10.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black 1

7
1
2
3
4
6
7
8
5
9
12
13
10
11
14
15
SHARK Waterproof Panel PC Exploded Drawing
10.1" SHARK Panel PC
No. Name Q'ty No. Name Q'ty
110.1" TOUCH 192I Mainboard 1
2SHARK 10.1,Washer for
Touch,LF,t=1.2mm 110BATTERY 2S3P 1
3SHARK 10.1",FRONT BEZEL-
WP,LF,AL 6063,Black 111BATTERY BRACKET 1
410.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black 112HDD BRACKET 1
5M12 CABLE WP x132.5" HDD 1
6LCD 114
SHARK 10.1",Bottom Cover-
WP,LF,AL 6063,Black 1
7SHARK 10.1,O-RING FOR FRONT
BEZEL, L=795MM,Black 115WP-VALVE 1
8SHARK 10.1",CHASSIS-
WP,2I268H/2I385H 1

8
5
4
1
8
18
3
15
16
14
13
17
19
10
12
7
6
11
2
SHARK Waterproof Panel PC Exploded Drawing
13.3" SHARK Panel PC
No. Name Q'ty No. Name Q'ty
113.3" FPPC-WP, Front Bezel 111SPONGE TOP SIDE 4
213.3" FPPC-WP, Bottom Cover 112SPONGE BOTTOM SIDE 4
3SHARK 13.3" Waterproof, O-RING 1132I Mainboard 1
4SHARK 13.3" Waterproof, Touch
Sponge W P 114BATTERY(OPTION) 1
513.3" Flat Resistive Touch Panel(W
P) 115BATTERY BRACKET(OPTION) 1
613.3" TFT-LCD 1162.5" HDD(OPTION) 1
713.3" Flat P-PC, LCM Bracket 217HDD BRACKET(OPTION) 1
810.1" BOX PC, Key Pad 118
M12 CABLE ATER
PROOF(OPTION) 11
9W P-VALVE 119PW 352(OPTION) 1
10 13.3_PANEL-CHASSIS_W P 1

9
5
4
1
8
3
2
9
18
15
16
17
14
12
10
7
6
11
13
SHARK Waterproof Panel PC Exploded Drawing
13.3" SHARK Panel PC
No. Name Q'ty No. Name Q'ty
113.3" FPPC-WP, Front Bezel 11013.3_PANEL-CHASSIS_W P 1
213.3" FPPC-WP, Bottom Cover 111SPONGE TOP SIDE 4
3SHARK 13.3" Waterproof, O-RING 112SPONGE BOTTOM SIDE 4
4SHARK 13.3" Waterproof, Touch
Sponge W P 1133I Mainboard 1
513.3" Flat Resistive Touch Panel(W P) 114BATTERY(OPTION) 1
613.3" TFT-LCD 115BATTERY BRACKET(OPTION) 1
713.3" Flat P-PC, LCM Bracket 2162.5" HDD(OPTION) 1
810.1" BOX PC, Key Pad 117HDD BRACKET(OPTION) 1
9W P-VALVE 118
M12 CABLE ATER
PROOF(OPTION) 11

10
IP (International Protection) code- Levels of Protection
IP XX
First digit "X", Protection against solids.
Protection against the contact of external solid bodies and the access to
dangerous par
Image Level
0—
No protection
Protect against the access with
any large surface of the body,
such as the back of a hand,
but no protection against deliberate
contact with a body part.
Protect against the access with
fingers or similar objects.
Protect against the access with tools,
thick wires, etc.
Protect against the access with
most wires, screws, etc.
Ingress of dust is not entirely
prevented, but it must not enter in
sufficient quantity to interfere with the
satisfactory operation of the equipment;
omplete protection against contact
No ingress of dust;
complete protection against contact
1>50 mm.
2>12.5 mm.
3>2.5 mm.
4 >1 mm.
5 Dust protected
6Dust tight
Dimensions of the
test material Description of test condition

11
Image Level
0——
Dripping water
(vertically falling drops)
shall have no harmful effect.
. Test duration: 10 minutes
. Water equivalent to
1mm rainfall per minute
Dripping water
No protection
Vertically dripping water
shall have no harmful effect
when the enclosure is tilted
at an angle up to 15° from
its normal position.
. Test duration: 10 minutes
. Water equivalent to
3-5 mm rainfall per minute
Dripping water
when tilted
up to 15°
Water falling as a spray at
any angle up to 60° from
the vertical shall have no
harmful effect.
. Test duration: 5 minutes
. Water volume:
0.7 Litre per minute
. Pressure: 80–100 kN/m²
Spraying water
Water splashing against the
enclosure from any direction
shall have no harmful effect.
. Test duration: 5 minutes
. Water volume:
10 litres per minute
. Pressure: 80–100 kN/m²
Splashing water
1
2
3
4
Protected
against
Description of
test condition
Description of
protection
Second digit “X”, protection against liquids.
Protection of the equipment inside the enclosure against
harmful ingress of water.

12
Image Level
Water projected by a nozzle
(6.3mm) against enclosure
from any direction shall have
no harmful effects.
. Test duration:
at least 3 minutes
. Water volume:
12.5 litres per minute
. Pressure: 30 kN/m² at
distance of 3m
Water jets
Water projected in powerful
jets (12.5mm nozzle) against
the enclosure from any
direction shall have no
harmful effects.
. Test duration:
at least 3 minutes
. Water volume:
100 litres per minute
. Pressure: 100 kN/m² at
distance of 3m
Powerful
water jets
Ingress of water in harmful
quantity shall not be possible
when the enclosure is
immersed in water under
defined conditions of
pressure and time
(up to 1 m of submersion).
Test duration: 30 minutes
Immersion at depth of 1m
Immersion
up to 1 m
The equipment is suitable for
continuous immersion in
water under conditions,
which shall be specified by
the manufacturer.
Normally, this will mean that
the equipment is hermetically
sealed.
However, with certain t
ypes of equipment, it can
mean that water can
enter butonly in such
a manner that it produces
no harmful effects.
. Test duration: continuous
immersion in water
. Depth specified by
manufacturer
Immersion
beyond 1 m
5
6
7
8
Protected
against
Description of
test condition
Description of
protection

13
Introduction of necessary tools
Adjustable ratcheting wrench (No. 21)
Torque wrench
Torque screwdriver
Purpose
Purpose
Purpose
If the waterproof connectors
are damaged, oxidized
or obsoleted, vse it to
unfasten them.
To examine if the torque
of each waterproof
connectors, are more than
5kgf-cm.
To examine the torque of
each upper cover screws
are more than
5kgf-cm.

14
IP66 Packing list
Material Code Description Detail Specification
1 by order Manual LF,M/B
2 6G8006-2349-0100 DVD-R
3 6G9053-0001-0100 Touch Pen LF,#9011
4 6G6001-2202-0100 SATA DATA Cable (Red,90°) LF,L=15cm
5 6G6003-1006-0100 SATA Power Cable LF,L=15cm,SATA to 2.0/1*4
6 Z0028-0004 Screw Package S3*4 SIO NI*10
7 6G7800-6042-0100 Thermal Pad LF,60*42.5*3mm
8 6G3623-3501-0000 Waterproof P-PC,HDD Kit LF,AL=1.6,Material
9 6G6005-3901-0100 Power Cord LF,King Cord
10 6G5212-0603-0200 60W Power
Adapter,12V/5A,2.5Ø LF,L Type(B043),FSP

15
IP67 Packing list
Material Code Description Detail Specification
1 by order Manual LF,M/B
2 6G8006-2349-0100 DVD-R
3 6G9053-0001-0100 Touch Pen LF,#9011
4 6G6005-3901-0100 Power Cord LF,King Cord
5 6G5212-0603-0200 60W Power
Adapter,12V/5A,2.5Ø LF,L Type(B043),FSP

16
Difference of Waterproof cables
4 PIN
8 PIN
12 PIN
POWER
USB LAN
COM VGA