Lexicon CP-1 User manual

CP-1 Quick Reference Guide
TostoreamodifiedPresetprogram,pressPARAMuntilthedisplayreads:MEMORIZEPROGRAM,thenpressanyofthe12programkeystostore
all current settings in the corresponding User register. User registers automatically store changes as they are entered.
The CP-1’s User Bank can be cleared and reloaded with duplicates of the factory Preset programs at any time. Turn on the CP-1 while holding
downPARAM. Continueto holddown PARAMfor severalseconds. This putsthe unit intoTEST mode. PushEFFECT MUTEto clearand reload
the User Bank and to restore all initial settings of Volume, Balance, Contrast, Configuration, etc. Push PARAM again to begin normal operation.
Note
ManufacturedunderlicensefromDolbyLaboratoriesLicensingCorporation.Additionallylicensedunderoneormoreofthefollowingpatents:U.S.numbers3,632,886,3,746,792and3,959,590;
Canadian numbers 1,004,603 and 1,037,877. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Lexicon CP-1 Digital Audio Environment Processor
tems.
BANK switches between 12 factory Preset
programs and 12 User registers where cus-
PARAM selects the various adjustable para-
meters of the current program.
PARAM: UP and DOWN adjust the current
parameter.
EFFECT: UP and DOWN adjust the level or
intensity of effects added by the CP-1.
BALANCE: F and Badjust the levels of the
rear speakers relative to the sides and fronts.
BALANCE: L and Radjust the left/right
balance of all speakers: front, sides and rear.
VOLUME: UP and DOWN adjust the level
of all channels simultaneously.
SYSTEM MUTE turns off all outputs and
lights both SYSTEM and EFFECT MUTE
LEDs.
EFFECTSMUTE turns off any effects added
by the CP-1. (Pushing EFFECT MUTE while
in system- mute mode turns the effects alone
back on.)
decay.
SURROUND works with film
sound tracks to recreate the theater
experience. MONO LOGIC expands
themusicandeffectsonmonauralfilms. STE-
REO LOGIC enhances music with surround
speakers. PRO LOGIC provides the same
decoding used in Dolby Stereo theater sys-
REVERB simulates halls and rooms
ofthreesizes with the aid ofsideand
rear channels. These programs have
fewer specific initial reflections than AMBI-
ENCE but richer and smoother reverberant
AMBIENCE simulates rooms
and concert halls of three different
sizes,generatingreflectionsofappro-
priate directionality, delay and spectral
shape and sending them to the side and rear
speakers.
PANORAMA provides greater
spaciousness and envelopment for
eithermusicorfilms.Theseprograms
canutilize left andright rearchannels but are
also effective using only two front loud-
speakers.
The Remote Control
INPUT LEVEL
SOURCE
SOURCE
TAPEMONITOR
PRE POSTTAPE SYSTEM
MUTE EFFECT MUTE POWER
III
DIGITAL AUDIO ENVIRONMENT PROCESSOR CP-1
exicon
The Front Panel
MUTE
EFFECT BALANCE VOLUME
BANK
PARAM
PANORAMA
123
AMBIENCE
456
7
REVERB
89
SURROUND
11 1210
NORMAL WIDE BINAURAL
SMALL MEDIUM LARGE
SMALL MEDIUM LARGE
MONO STEREO
EFFECTSYSTEM
B
F
L
R
DOLBYSURROUND
PRO - LOGIC
OD
D
B
B
Y
Y
S URROU
N
D
CGO I
L
L
O
RP
OD BY
S URROU
N
D
CGO I
L
L
O
RP

Lexicon Part # 070-06620 Rev. 1.0
The Rear Panel
Configuration
Push Phantom/In if you have no center channel; leave it out if a center speaker is connected.
Leaving this button out with no center channel will cause the Surround programs to malfunction.
Patents are pending on the CP-1
1
Center Phantom
Button IN
3
Center Phantom
Button IN
4
Center Phantom
Button IN
2
Center Phantom
Button IN
5
8
7
10 11 12
Center Phantom
Button IN
9
Center Phantom
Button IN
6
Choose the diagram that most closely corresponds
to your room and note its number.
3 Oak Park
Bedford, MA 01730 USA
Lexicon CP-1 Digital Audio Environment Processor Quick Reference Guide
© 1988 Lexicon, Inc.
REAR SIDE LEVEL
SUBWOOFER
CENTER/OUT
PHANTOM/IN
L
R
L
R
OUTPUTS
TAPE
OUT TAPE IN
L
R
INPUTS
L
R
III
MAIN CENTER SUB
Press BANK and hold for five seconds. The
display will read: LCD CONTRAST ADJ. The CP-
1 is now in Configuration mode.
•Use PARAM UP or DOWN to adjust display
contrast.
Push PARAM to select the Speaker Configuration
menu.
•PushPARAMUP orDOWN untilthe configura-
tion you have chosen and the description in the
display match.
If you are using only one rear speaker it may be
hooked up to either the left or right rear output, as
longas youuse the correctConfiguration number.
Subwoofersarenot showninany of theseconfigu-
rations.Consult the subwoofer owner's manualor
your dealer for proper placement of subwoofers.
speaker connected to
center output
speakers connected to
Main outputs
speakers connected to
Side outputs
speakers connected to
Rear outputs