Lexicon CP-3 User manual

Lexicon Part # 070-09929 © 1994 Lexicon, Inc.
To turn on the system
Input 1:
Input 2:
Input 3:
Input 4:
3 Oak Park • Bedford, MA 01730 USA • Tel [phone] • Fax [phone]
Lexicon CP-3 PLUS Digital Surround Processor Quick Reference Guide

The Standard remote — and this Quick Reference Card — are designed for simplified use
of the CP-3 PLUS after all installation, calibration, and customization of your system is
complete.
3. Input
Eachofthesebuttonsselectsan
Input source (TV, CD, VCR,
etc.) These sources will have
been assigned and named dur-
ing installation — and may also
havebeenprogrammedtoauto-
matically engage specific ef-
fects.
1. The Effects
These buttons should have
been customized by your in-
stalller to load the following
effects:
NIGHTCLUB — for intimate
listening of any type of music.
CONCERT HALL — for large-
scale, orchestral music..
MUSIC SURROUND — for
any type of music – and an
interestingwaytolistentoste-
reo films which are not sur-
round encoded.
TELEVISION — provides sur-
round effects for television
viewing. If you think the pro-
gram material may be sur-
round encoded, try pressing
MOVIES.
MOVIES — designed for any
movies, music, or television
programs which are surround
sound encoded.
2. Balance
These buttons move the
sound between your front and
surround speakers.
4. On/Off
Puts the CP-3PLUS into
standby. (The master power
switch is on the rear panel of
the CP-3PLUS.)
5. Volume
Thesebuttonsadjusttheover-
all volume of your system –
Hold either button down to
change volume rapidly.
6. Mutes
MAIN MUTE turns off all out-
puts. Pressing again will re-
store normal operation. (It is
possible to change VOLUME
while the system is muted –
check this before you turn the
mute off again.)
EFXMUTEallowsyoutolisten
to the source material without
the effects added by the
CP-3PLUS. This is also the sim-
plestwaytoplay“normal”two-
speaker stereo. Pressing
again will restore normal op-
eration.
The Standard Remote
TheCP-3PLUSisanaudioproc-
essor designed to enhance
the listening experience of
any source material you
choose — any type of music,
a vintage film or the latest
surround sound encoded
movie or TV program.
Yoursystem should alreadybe setup and readyto use.Simply
turn your system on and decide what source you want to play
(TV, VCR, etc.) Once you have selected your source material,
turn on the CP-3PLUS with the Standard remote (4).
Selecting an Input
Getting Started
Note: TheCP-3PLUS hastworemotecontrols:theExpandedremoteandthe
Standard remote. The system will respond to whichever remote was last
used to turn it on.
Alternatively, holding any of
the Input buttons displays
the name of the source as-
signed to that Input. Press
Input 1 and hold the button
down. The display should
now show:
INPUT 1 XXdB
COMPACT DISC*
* or other name such as VCR, TV, etc. as-
signed by your installer
During installation, each of
the four Input buttons (3) on
the Standard remote will
have been assigned to load
one of your audio/video
sources. (See the reverse
side of this card for these
assignments.)
The display should show
brief Copyright and customi-
zation messages, then the
current effect. A typical ex-
ample might look like this:
BANK B SURROUND
10 TELEVISION*
* or other name assigned by your installer
Whenyoureleasethebutton,
the display will show the cur-
rent effect.
With an input selected, you
can press any of the effect
buttons(1)tolistentoadiffer-
ent effect.
AdjustVOLUME(5)andBAL-
ANCE (2) to maximize the ef-
fect at your listening position.
Lexicon CP-3PLUS Digital Surround Processor
3 Oak Park • Bedford, MA 01730 USA • Tel [phone] • Fax [phone]
CP-3 PLUS Quick Reference Guide