LG SC100 User manual

Owner's Manual
Laser Display Screen
Please read the safety information carefully before using the product.
www.lg.com
P/NO : MFL67864901 (1302-REV00)
SC100

2Safety Precautions
CAUTION
 Follow the instructions in the manual
to install the product.
- Otherwise, it may cause serious
injury or damage to the product.
 When installing the product or ad-
justing the height of the product, two
or more people are needed.
- If you do it by yourself, you may
drop the product causing personal
injury or damage to the product.
 When installing the product, check
whether the wall is strong enough to
hold the product and use the anchors
and screws provided.
- Otherwise, they may not bear the
weight of the product causing safety
issues.
Installation
WARNING
 The product should be installed by
a qualified professional specified by
the retail store.
- The product installation by a non-
qualified personnel is dangerous
and may cause personal injury.
 The product should be installed
where its weight can be supported.
- Otherwise, the product may fall and
cause personal injury.
 When moving or replacing the prod-
uct after installation, contact a quali-
fied installer specified by the retail
store.
- If an unqualified person moves and
installs the product, this may cause
safety issues as this task requires
the special technique.
 Do not hang on the product or apply
shock to the product.
- The product may fall and cause
injury.
Safety Precautions
Please take note of the safety instructions to prevent any potential accident or misuse
of the product.
 Safety precautions are given in two forms, i.e. Warning and Caution as detailed be-
low.
WARNING: Failure to follow the instructions may cause serious injury and even
death.
CAUTION: Failure to follow the instructions may cause minor injury or damage to
the product.
 Read the owner's manual carefully and keep it to hand.

3
Safety Precautions
 When drilling the holes in the wall,
make sure you use a drill and a drill
bit with the specified size of diam-
eter.
Ensure that you also follow the in-
structions regarding the depth of the
holes.
- Otherwise, the product may be
installed improperly causing safety
issues.
 Do not clean the product with wet
towels, and do not use a heater or
humidifier underneath the product.
- Moisture permeating into the
product, steam or heat may result in
fire, electric shock or damage to the
product.
 Keep the product away from sprin-
klers, sensors, high-tension wires
and power sources. Do not install the
product in a location where vibrations
or shock impacts are likely to occur.
 Wear working gloves when installing
the product. Do not use bare hands.
- Otherwise, it may cause personal
injury.

4PREPARATION
PREPARATION
Accessories
Check the accessories provided with the product.
The picture may be different from the actual product.
Accessories are subject to change without prior notice in order to improve the perfor-
mance of the product. New accessories may be added or old ones may be removed.
Preparations
Drill (M6, M8), leveler, tapeline, driver, tape
Up
Down
2 rings 12 space steels Paper screen
6 anchors for fixing ring
(Ф8)
6 bolts for fixing ring
(Ф8)
Magnet
10 EA
Tape 6 EA

5
Installation
INSTALLATION
Fixing the Anchor, Screw
CAUTION
 Check the material of the wall and the thickness of the finishing.
 
Use the anchors for wall material of concrete, light concrete, strong natural
stone, soft natural stone masonry
 brick and hallow block that do not crack.
 
When installing the product on wall material not designated, install the
product so that each fixated location can withstand the pull out load of 70
kgf (686 N) and shear load of 100 kgf (980 N) or above.
a. Use a drill bit Ø8 mm to drill a hole for the anchor location within a depth of
80 mm - 100 mm.
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the
angle adjusting part to face upward.
Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque
of 45 kgf/cm - 60 kgf/cm.
ab
c
d
Anchor
Ring and Space steel fixing screw

6Installation
INSTALLATION STEP
1 Attach a paper screen to the place where the screen will be located. (The paper
screen helps to easily install the adjustable bracket and bore holes in the wall.)
2 Install the ceiling mounting bracket while aligning the center of the main unit with
the center line of the paper screen.
3 Install the ceiling mounting bracket, ensuring that the distance from the wall to the
center of the adjustable bracket is 570 mm.
4 Install the ceiling mounting bracket, ensuring that the distance from the top of the
paper screen to the top of the adjustable bracket is 370 mm.
Up
Down
570 mm
170 mm
370 mm 160 mm
365 mm
Paper screen
Center line

7
Installation
5Two people lift the screen up until its bottom edge is level to the magnets at the
bottom of the paper screen. Put the screen close to the wall aligning with the loca-
tions marked with the tapes and hang the brackets on the rings by carefully pulling
it down.
CAUTION
 If the screen is tilted when pulling it down, the screen may not fix to the bracket
and result in damage to the screen.
Tape
Down
Up
Magnet
10 mm

8Installation
CAUTION
 If the screen is tilted when pulling it down, the screen may not fix to the bracket
and result in damage to the screen.
6Move the screen in all directions to check whether the screen is securely hung on
the rings.

9
Laser Display Adjustment
Laser Display Adjustment
<Rotation>
<Tilt>
<Horizontal movement>
<Vertical movement>
Adjustment Type Function
Rotation Screen Horizontality
Tilt Screen Verticality
Horizontal movement Horizontal location
Vertical movement Screen size

10 SPECIFICATIONS
SPECIFICATIONS
1272
1073 142
309 1626
2245
Model SC100
Width (mm)
2245 ± 5 mm
Height (mm)
1272 ± 3 mm
Frame Height (mm)
12.0 ± 1.0 mm
Depth (mm)
9.1 ± 0.2 mm
Weight (kg)
31.2 ± 1.0 kg