LG 14HK701G-W.AUB User manual

Please read this manual carefully before operating your set and retain it for future reference.
14HK701G-W
www.lg.com
Copyright © 2019 LG Electronics Inc. All Rights Reserved.
OWNER’S MANUAL
Flat Panel Digital X-ray Detector

2
ENGLISH
CONTENTS
OPEN SOURCE SOFTWARE
NOTICE INFORMATION---------------------------------3
ON CLEANING --------------------------------------------3
GENERAL DESCRIPTION -------------------------------3
PART NAME AND FUNCTION--------------------------6
ASSEMBLING BATTERY ------------------------------ 11
REMOVING BATTERY ---------------------------------12
SPECIFICATION AND
DIMENSION OF EACH PART -------------------------13
ENVIRONMENTAL REQUIREMENT-----------------20
CALIBRATION SOFTWARE INSTALL --------------- 20
CONNECTION TYPES ----------------------------------21

3
ENGLISH
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping, and handling) upon email request to
opensourc[email protected]om.
This offer is valid for a period of three years after our last shipment of this product.This offer is valid to anyone
in receipt of this information.
ON CLEANING
Recommended Cleaning Chemicals
•Isopropanol 100%
•Ethanol 70%
•Cidex® OPA
•0.9% NaCl solution
•
How to Use Cleaner
•Prior to cleaning, turn off the Detector and remove the power cable.
•Soak a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1 N of force.
•The cleaner could cause serious damage if it leaks inside the Detector while cleaning.
•Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.
•Cleaning guidelines for Detector must only be carried out by medical professionals (doctors or nurses) and
must not be handled by patients.
GENERAL DESCRIPTION
Overview
This model is an x-ray imaging device, a system that can acquire and process X-ray images as digital images. It
utilizes amorphous silicon and a high-performance scintillator to ensure sharp high-definition image quality
with the resolution of 3.6 lp/mm and the pixel pitches of 140 um. This device is a flat panel based X-ray image
acquisition device.This device must be used in conjunction with an operating PC and an X-ray generator. This
device can be used for digitizing and transferring X-ray images for radiological diagnosis.The data transmission
between the Detector and PC can be enabled with a wired (cable) or wireless connection.
Product Component
•Detector: 14HK701G
•Control Box : LG Control Box
-AC power cord for Control Box
•Battery Charger : LG Battery Charger
•2 Battery (LBQ7222L)
•AC Power adapter for Charger (DA-65J19)
•AC Power cord for AC Power adapter
•Cable
-Main Cable : Detector and Control Box link cable (Supply DC power, Ethernet data, control signals of X-ray
Generator)
-Trigger Cable: X-ray Generator to Control Box, transmit control signal between Detector and X-ray
Generator. (Optional)
-LAN Cable: Control Box to PC, exchanges Ethernet data between PC and Detector. (Optional)
•CD: Owner's Manual, Calibration Software
•Regulatory Manual, Inspection Report

4
ENGLISH
Basic Accessories
100kg
Detector 1 EA Battery 2 EA AC Power cord for AC Power adapter 1EA Inspection Report 1EA
CD (Owner's Manual / Calibration Software) 1 EA Main Cable 1EA Regulatory Manual 1 EA AC Power adapter for Charger 1 EA
Charger 1 EA Control Box 1EA AC Power cord for Control Box 1EA

5
ENGLISH
Optional Accessories
Trigger Cable 1EA LAN Cable 1EA
•Some models may not include additional accessories.
CAUTION
•You must use the authorized components as per the specification below. Unauthorized components may cause damage and/or cause the product to malfunction.
Component Standard
LAN Cable More than CAT5E Standard
Power Cord US – Approved Medical grade regulation
Others – Approved country safety regulation
•The AC/DC adapters etc. that are being used, with the exception of the upper components, must be supplied by the manufacturer.

6
ENGLISH
PART NAME AND FUNCTION
Detector
FRONT BACK
100kg
1

7
ENGLISH
SIDE
3
2
4
1
Battery
2
Power Button: Power on/off switch
(On : press over 1 Sec, Off : press over 5 Sec)
3
LED Indicator: Indicating Detector’s status
4
Connection to Main Cable
LED LED Color Status
Green Battery is more than 30 % charged.
Orange Battery charging status is 10 ~ 30 %.
Orange Blinking Battery is less than 10 % charged.
Green Ethernet/Wireless(Station) connection
Green Blinking Wireless(Station) disconnected
White Wireless(AP) connection
White Blinking Wireless(AP) disconnected
Off Ethernet disconnected
Green Power On
Green Blinking Sleep mode
Off Power Off

8
ENGLISH
Battery and Charger
NOTE
•Battery: Li-ion polymer battery (Charging time -Typ. 4 hours)
•Battery pack itself shows the remaining battery percentage.
•Battery charger: 3 ports cradle type
•LED Indicator: Following LEDs are located to each battery.
LED Indicator Status
Green Completion of charging
Orange On charging
Orange Blinking Error (Connection error, etc)
Battery Remain Indicator Battery Level
75 ~ 100%
50 ~ 75%
25 ~ 50%
0 ~ 25%

9
ENGLISH
Control Box
AC-IN T4L 250V
Ethernet Sync
DXD 1 DXD 2
Power Ethernet Ready Exposure
1
AC-IN T4L 250V
Ethernet Sync
DXD 1 DXD 2
Power Ethernet Ready Exposure
7
5
2 3
6
4
No. LED Indicator LED Color Status
1
Green Power normal operation
Off Power off (AC power cord no connection or Power error)
Green Ethernet normal operation
Green blink On data communication
Off Ethernet disconnected
Green Ready signal from X-ray Generator is active
Off Ready signal from X-ray Generator is inactive
Orange blink Power error
Orange Exposure signal from X-ray Generator is active
Off Exposure signal from X-ray Generator is inactive
Orange blink Power error

10
ENGLISH
No. LED Indicator LED Color Status
2
None
Connecting the Control Box and the Detector A.This connector supply power (24V 2.1 A) to the Detector, transmits X-ray synchronization signals and
Ethernet image data.
3
Connecting the Control Box and the Detector B. This connector supply power (24 V 2.1 A) to the Detector, transmits X-ray synchronization signals and
Ethernet image data.
Control Box supports 2 Detector connections. Usage is, one is for Bucky stand, the other is for table (bed). Generally, X-ray room of hospital installs 2
Detectors, Bucky stand and table type, it's far more convenient and efficient working environment.These 2 Detectors are not operated simultaneously,
control box selects the operating Detector by AWS command.
4
Connects AC power cord.
5
Ethernet port to transmit image/command between the Detector and PC.
6
This is to synchronize the Detector and X-ray Generator.
7
Control box power fuses are 4A, 250V toType T fuse.
Power rating:T4L 250V

11
ENGLISH
ASSEMBLING BATTERY
1 Check the battery mounting hole direction. 2 Insert into the hole on the side with the indicator. 3 Press the opposite side to secure the battery indicator.

12
ENGLISH
REMOVING BATTERY
1 Push the battery lock button in the direction of the picture. 2 Remove the battery by lifting it in the direction of the picture.

13
ENGLISH
SPECIFICATION AND DIMENSION OF EACH
PART
The product specifications are subject to change without prior notice for product improvements.
~ refers to alternating current (AC), refers to direct current (DC).
Specifications
Detector
Item Specification
Model 14HK701G
Sensor type Amorphous Silicon TFT
Scintillator Type CsI:TI
Total Pixel Matrix 2500 x 3052 pixels
Total Pixel Area 350 x 427.28 mm
Pixel Pitch 140 um
Effective Pixel Matrix 2488 x 3040 pixels
A/D Conversion 16 bits
Data transmission 802.11 a/b/g/n/ac Wireless LAN Standard, 150 Mbps
Wired Gigabit Ethernet Standard, 500 Mbps
Cycle time Typ. 8 Sec (Wired)
Typ. 11 Sec (Wireless)
Image Transmission Typ. 2 Sec (Wired)
Typ. 2.5 Sec (Wireless)
Image Storage Stores up to 200 images
Energy range 40 kVp ~ 150 kVp
MTF Typ. 89 % at 0.5 lp/mm
DQE Typ. 72 % at 0.1 lp/mm
Item Specification
Size
(Width x Height x Depth)
384.0 x 460.0 x 15.2 mm
(15.1 x 18.1 x 0.5 inch)
Weight Typ. 2.95 kg (6.5 lbs)
Window material Carbon Fiber
Trigger mode Manual Mode
Auto Mode (Auto Exposure Detection)
Power consumption Typ. 28 W
Wireless Standard:
802.11 a/b/g/n/ac compliance
Peak mode: 867 Mbps
Frequency: 2.4 GHz / 5 GHz
Bandwidth: 20 MHz / 40 MHz / 80 MHz
MIMO: 2X2
Rating 24 V 2.1 A
Applied part Type: BF
Location:The front side of the Detector (Effective area only).
NOTE
•Maximum wireless signal rate derived from IEEE standard specifications. Actual data throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
•Recommended Maximum operable distance: 2 m (6.5 ft) (From the Access Point)
•Wireless antennas: The module adopts the latest 802.11ac technology. The transmitter of the module is
powered by host equipment (Detector).The antennas are 2 printed-dipole antennas.
•Wireless module: 802.11 a/b/g/n/ac USB2.0 module is implemented. It supports 2T2R (2 transmit 2 receive)
MIMO technology, which delivers throughput up to 300 Mbps.
•Images can be saved by the X-ray generator while the power of the detector is turned on without connecting
to a PC.To produce images, X-ray is irradiated at intervals of more than 10 seconds. Check and load the saved
images from .

14
ENGLISH
Detector has been tested with below table’s X-ray condition.This table is only for reference.The legally certified
radiologist expert should control X-ray dose.
•Sensor Type: a-Si TFT, X-ray conditions
Adult
SID (inch / cm) Tube Voltage (KV) Tube Current (mA) Tube Current xTime
(mAs)
Chest P-A 72 inch / 182.8 cm 110 KV 320 mA 3.2 mAs
C-spine LAT 72 inch / 182.8 cm 75 KV 200 mA 20 mAs
L-spine A-P 40 inch / 101.6 cm 70 KV 250 mA 25 mAs
Abdomen A-P 40 inch / 101.6 cm 75 KV 320 mA 20.48 mAs
Pelvic A-P 40 inch / 101.6 cm 70 KV 250 mA 25 mAs
Wrist A-P 40 inch / 101.6 cm 50 KV 250 mA 5 mAs
Elbow A-P 40 inch / 101.6 cm 55 KV 250 mA 5 mAs
Shoulder AP 40 inch / 101.6 cm 65 KV 200 mA 8 mAs
Foot A-P 40 inch / 101.6 cm 50 KV 250 mA 5 mAs
Ankle A-P 40 inch / 101.6 cm 55 KV 100 mA 6.4 mAs
Knee A-P 40 inch / 101.6 cm 60 KV 100 mA 8 mAs
•Sensor Type: Oxide TFT, X-ray conditions
Adult
SID (inch / cm) Tube Voltage (KV) Tube Current (mA) Tube Current xTime
(mAs)
Chest P-A 72 inch / 182.8 cm 110 KV 320 mA 2.56 mAs
C-spine LAT 72 inch / 182.8 cm 75 KV 200 mA 16 mAs
L-spine A-P 40 inch / 101.6 cm 70 KV 250 mA 20 mAs
Abdomen A-P 40 inch / 101.6 cm 75 KV 250 mA 16 mAs
Pelvic A-P 40 inch / 101.6 cm 70 KV 250 mA 20 mAs
Wrist A-P 40 inch / 101.6 cm 50 KV 200 mA 4 mAs
Elbow A-P 40 inch / 101.6 cm 55 KV 200 mA 4 mAs
Shoulder AP 40 inch / 101.6 cm 65 KV 200 mA 6.4 mAs
Foot A-P 40 inch / 101.6 cm 50 KV 200 mA 4 mAs
Ankle A-P 40 inch / 101.6 cm 55 KV 100 mA 4.8 mAs
Knee A-P 40 inch / 101.6 cm 60 KV 100 mA 6.4 mAs
NOTE
•In the case of the Oxide TFT X-ray condition table, it is only applicable to 14HQ901G-B and 17HQ901G-B
models. If the condition table is applied to other models, the desired image may not be obtained.
•Regarding paediatric dosage, it should be much less than for an adult.The certified radiologist should pay
special attention to paediatric X-ray dosage levels.

15
ENGLISH
GRID
Item Recommended Specification
SID 100 cm / 130 cm / 150 cm / 180 cm
(39.3 inch / 51.1 inch / 59 inch / 70.8 inch)
Size 384 x 460 mm
(15.1 x 18.1 inch)
Ratio 10 : 1
Frequency 215 Line / Inch
Inter Spacer AL
Battery
Item Specification
Model LBQ7222L
Size
(Width x Height x Depth)
204.6 x 110.5 x 7.8 mm
(8.0 x 4.3 x 0.3 inch)
Weight Typ. 0.24 kg (0.5 lbs)
Output Nominal voltage Typ. 7.5 V
Operation Temp 10 °C (50 °F) ~ 35 °C (95 °F)
Charging time 4 hours (standard) when charging with the Detector.
3 hours (standard) when charging two batteries with the charger.
Capacity Typ. 4000 mAh, Min. 3850 mAh
Battery performance Typ. 260 shots/6.5 hours
Min. 160 shots/4 hours (Cycle time 90 Sec, with Full charged battery)
Battery Charger
Item Specification
Model LG Battery Charger
Size
(Width x Height x Depth)
125.0 x 90.0 x 255.0 mm
(4.9 x 3.5 x 10.0 inch)
Weight Typ. 0.9 kg (1.9 lbs)
Input 19 V 3.42 A
Output Nominal voltage 8.7 V
Battery Charger Adapter
Item Spec
Model DA-65J19
Manufacturer Asian Power Devices Inc. (APD)
Size (Width x Height x Depth) 134.0 x 59.8 x 31 mm (5.2 x 2.3 x 1.2 inch)
Weight Typ. 0.3 kg (0.6 lbs)
Input AC 100-240V~ 50-60 Hz, 1.5 A-0.7 A
Output 19 V 3.42 A
Classification by protection type against Electric Shock Class equipment
Cable length 1.5 m (4.9 ft)

16
ENGLISH
Control Box
Item Specification
Model LG Control Box
Size
(Width x Height x Depth)
125.0 x 109.8 x 255.0 mm
(4.9 x 4.3 x 10.0 inch)
Weight Typ. 1.3 kg (2.8 lbs)
Input AC 100-240V~ 50/60 Hz, 1.4-0.7 A
Output DXD 1
24 V 2.1A, Trigger signals, Ethernet data for Detector A.
DXD 2
24 V 2.1A, Trigger signals, Ethernet data for Detector B.
Control Box supports 2 Detector connection.
Usage is, one is for Bucky stand, the other is for table (bed).
Generally, X-ray room of hospital installs 2 Detectors, Bucky stand and table
type, it's far more convenient and efficient working environment.
These 2 Detectors are not operated simultaneously, control box selects the
operating Detector by AWS command.
Ethernet
Transmission image/command between the Detector and PC.
Sync
Transmission control signals between the Detector and X-ray Generator.
Cables
Item Length Qty
Main Cable 7 m (22.9 ft) 1
LAN cable (Optional) 10 m (32.8 ft) 1
Power cord (110 V or 220 V) 1.5 m (4.9 ft) 2
Trigger Cable (Optional) 15 m (49.2 ft) 1

17
ENGLISH
Dimension
Detector
Unit: mm (inch)
Front Side
100kg
100kg
384.0 (15.1)
460.0 (18.1)
100kg
15.2 (0.5)

18
ENGLISH
Control Box
Unit: mm (inch)
Front Side
Power Ethernet Ready Exposure
125.0 (4.9)
Power Ethernet Ready Exposure
255 (10.0)
109.8 (4.3)

19
ENGLISH
Battery
Unit: mm (inch)
Front Side
204.6 (8.0)
110.5 (4.3)
7.8 (0.3)
Battery Charger
Unit: mm (inch)
Front Side
125.0 (4.9)
90.0 (3.5)
255.0 (10.0)

20
ENGLISH
ENVIRONMENTAL REQUIREMENT
PC System requirement
PC Specification
CPU Intel i5
Memory 4 GB
Disk capacity At least 10 GB ~ 500 GB recommended
Network card Dual Ethernet 100/1000 Mbps
OS Windows 7/8.1/10 (32bit, 64bit)
Monitor Min. Resolution 1280x720
AP Cisco models recommended (e.g. Linksys EA9200)
CALIBRATION SOFTWARE INSTALL
How to install
Run the calibration software installation file. Once the installation file has been executed, follow the installation
instructions on the screen.
How to delete
You can delete the Calibration Software in the following ways:
Deleting from the Control Panel
1 Select Control Panel from the Start menu.
2 Select Programs and Features in Control Panel.
3 Select the [LG DXD Calibration] on the lists.
4 When the program installation and deletion screen appears on the screen, select the [Delete] button.
5 Follow the deletion instructions on the screen and click the [Next] button to proceed.
Deleting with the installation file
1 Run the calibration software installation file, then follow the deletion instructions on the screen.
NOTE
•When using the installation file to delete the program, the [Installation file] must be the same version as the
current software.