Life Fitness CSLAT User manual

CLUB SERIES LAT PULLDOWN
Part # 6941801
Rev A.
Revision:08/02/001
ASSEMBLY INSTRUCTIONS

PARTS LIST
KE
Y
PART
#
DESCRIPTION QT
Y
KE
Y
PART
#
DESCRIPTION QT
Y
1 69046xx ASSY TOWER 1 9 3102922 3/8 X 2-3/4” BOLT 8
1A 6920001 CABLE 110 3102905 3/8 X 3-3/4” BOLT 4
1B 6714901 GUIDE ROD BUSHINGS 2 11 3102807 3/8” LOW HEIGHT LOCK NUT 10
2 69032xx WLDMT, MAIN UPRIGHT 1 12 6957001 WEIGHT STACK LABEL 1
2A 6692601 3 X 2 END CAP 1 13 3102514 3/8” SAE WASHER 8
2B 6902201 SUPPORT HOOK CHROME 1 14 6866701 3/8” RH WASHER 22
2C 3222801 4.5" PULLEY 3 15 6913801 WEIGHT STACK SELECTOR PIN 1
2D 3102933 3/8-16 X 2 BOLT 1 16 3108001 WEIGHT STACK CUSHION 2
2E 3102903 3/8-16 X 2.5 BOLT 1 17 6866601 BLACK RH CAP 2
2F 3102922 3/8-16 X 2.75 BOLT 1 18 68775xx SEAT PAD 1
2G 6866701 3/8 RH WASHER 8 19 3222001 1” SHAFT COLLAR 2
2H 6866601 CAP RH 20 BLK 8 20 6714901 GUIDE ROD BUSHING 2
2I 3102807 3/8-16 NYLOCK NUT LOW HT 4 21 3103801 SNAP LINK 1
2J 3102514 3/8 FLAT WASHER 6 22 6941601 PLACARD LABEL 1
2K 6480301 3/8 SPACER 2 23 6941701 LANGUAGE PLACARD LABEL 1
2L 6827001 CABLE CLIP 1 24 6887202 10 LB. WEIGHT PLATE (STD) 20
2M 3102904 3/8-16 X 3 BOLT 1 25 6888402 15 LB. WEIGHT PLATE (OPT) 10
2N 6122702 3/8 SPACER 2 26 6926801 GUIDE ROD 2
3 69047xx ASSY BENCH FRAME 1 27 6866602 RH CAP WHITE 20
4 6907002 ASSY LAT BAR 1 OR 6866603 RH CAP PLATINUM 20
4A 3103107 RUBBER GRIP 2 27S 3221601 STARLOCK WASHER 12
5 6901402 KNEE SUPPORT BLK 1 28 3202405 3/8 X 3-1/2” BUTTON HEAD BOLT 12
5A 6928101 ROLLER PAD 229 6921207 FRONT PARTIAL SHROUD 1
5B 6405201 2 SQ END CAP 1 30 6861502 REAR PARTIAL SHROUD 1
5C 3222701 SHAFT COLLAR 2 31 6914602 FULL FRONT SHROUD 1
5D 3119303 1.25 END CAP 2 32 6924802 FULL REAR SHROUD 1
6 69010xx WLDMT, GUIDE ROD SUPPORT 1 33 6957001 WEIGHT STACK LABEL 1
7 6851501 TRICEP ROPE 1 34 6957101 HEAVY WEIGHT STACK LABEL 1
8 6923602 HEAD PLATE BLK 1
*For all 5 digit part numbers you need to add the color at the end. **Language placard kit comes with Dutch, French,
For shrouds and weldments please use the following codes: German, Poruguese, Spanish, Japaneese, and
xxxxx07 Denotes Platinum Italian.
xxxxx08 Denotes White
*For upholstery, please use the following codes:

STEP 1:
FIGURE 1
4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• LOOSELY assemble the TOWER (1) to the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/4” BOLTS (10),
four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 1.
1
10 3/8 X 3-3/4”
11
3
27
14
1B

1A
2
2N
2A
2M
2D
2E
2L
2K
2C
2I
2G 2J
2F
2H
2B
1A

5
FIGURE 2
STEP 2:
• LOOSELY assemble the MAIN UPRIGHT (2) to the base of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/
4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 2.
3/8 X 3-3/4” 10
9 3/8 X 2-3/4
27
14 13
2
11
3
• LOOSELY assemble the MAIN UPRIGHT (2) to the top tube of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X
2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS
(11) as shown in FIGURE 2.
•Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS
(27) over the RH WASHERS (14) on all tightened connections.
1A
1B

6
0123456
1/2 1/2 1/2 1/2 1/2 1/2
FIGURE 3
STEP 3:
• SECURELY assemble the KNEE SUPPORT (5) to the BENCH FRAME (3) using two BLACK RH CAPS (17), two RH CAPS
(27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT
LOCK NUTS (11) as shown in FIGURE 3.
11
17
13
14
5
3
9 3/8 X 2-3/4”
27
5C
5B
5A
1A
5D

7
STEP 4
FIGURE 4
• SECURELY assemble the SEAT PAD (18) to the BENCH FRAME (3) using two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9) and
two 3/8” RH WASHERS (14) as shown in FIGURE 4.
3/8 X 2-3/4” 9
14
27
3
18
5A

8
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP 5:
FIGURE 5
• Insert the two GUIDE RODS (26) (found in the SHROUD KIT) into the base of the TOWER (1) as shown in FIGURE 5. Lubricate
the GUIDE RODS (26) with a slicon or teflon spray that is available at most hardware stores.
• Slide two WEIGHT STACK CUSHIONS (16) down over the GUIDE RODS (26). See FIGURE 5.
• Using EXTREME CARE place twenty 10 LB. WEIGHT PLATES (24) over the GUIDE RODS (26) as shown in FIGURE 5.
(NOTE: If HEAVY WEIGHT OPTION is being used, slide ten 15LB. WEIGHT PLATES (25) over the GUIDE RODS (26)
first, then slide ten 10 LB. WEIGHT PLATES (24) over the GUIDE RODS.)
• Carefully Slide the HEAD PLATE (8) down over the GUIDE RODS (26) onto the weight stack as shown in FIGURE 5.
• Slide one WEIGHT STACK SELECTOR PIN (15) over the shaft on the HEAD PLATE (8) as shown in FIGURE 5.
• Slide two GUIDE ROD BUSHINGS (20) over each GUIDE ROD (26).
• Slide two 1” SHAFT COLLARS (19) over each GUIDE ROD (26) as shown in FIGURE 5.
• Place the GUIDE ROD SUPPORT (6) over the GUIDE RODS (26) as shown in FIGURE 5.
16
24
26
8
15
19
20
6
1
25
HEAVYWEIGHT
OPTION
24
1A

9
• Screw the treaded end of the CABLE all way into the end of the shaft on the HEAD PLATE (8) and tighten jam nut securely. See
FIGURE 6.
STEP6:
FIGURE 6
• SECURELY assemble the GUIDE ROD SUPPORT (6) to the TOWER (1) and MAIN UPRIGHT(2) using four RH CAPS (27), two
3/8 X 2-3/4” BOLTS (9), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 6.
TIGHTEN!
9 3/8 X 2-3/4”
8
15
• Slide GUIDE ROD BUSHINGS (20) into the tubes on the GUIDE ROD SUPPORT (6), slide 1” SHAFT COLLARS (19) under-
neath the GUIDE ROD BUSHINGS (20) and SECURELY tighten the set screws.
19
6
20
1
27
26
24
14
11
2
• Insert the WEIGHT STACK PIN (15) into the WEIGHT STACK as shown in FIGURE 6.
1A

0123456
1/2 1/2 1/2 1/2 1/2 1/2
10
ST`````
FIGURE 7
• Peel the backing off the WEIGHT STACK LABELS (12), line up sheet to the right of the selector opening and apply labels to
the WEIGHT PLATES (24), starting with the HEAD PLATE (8) as shown in FIGURE 7.
12
8
24
TIGHTEN!
• The WEIGHT STACK LABEL sheet (12) includes labels for both lbs. and kgs. for both the standard and optional weight stacks.
• REFERTOSHROUD KITASSEMBLYINSTRUCTIONS.