Life Fitness SM42 User manual

M051-K50-A142 1
4 STACK MULTI-JUNGLE (SM42)
WITH 2 ADJUSTABLE PULLEYS
UNPACKING AND ASSEMBLY INSTRUCTIONS

SM42 Unpacking & Assembly Instructions
2
The SM42 comes partially assembled. Follow the steps below to complete the assembly.
WARNING: COMPONENTS OF THE SM42 ARE LARGE AND HEAVY. USE CAUTION
WHEN ASSEMBLING THIS MACHINE.
MATERIALS AND TOOLS REQUIRED FOR ASSEMBLY
1/2”, 3/8”, 5/8” & 9/16”
Socket wrench 1/8” Hex key wrench 5/8” & 9/16” Combination wrench Pinch bar
You will also need a ladder and a piano dolly to lift and position the weight stacks.
ASSEMBLY TIME
Two people can accomplish this assembly in approximately 2 hours.

SM42 Unpacking & Assembly Instructions
3
UNPACKING
Follow the steps below when unpacking the components of the SM42.
1. Cut off the shipping wrapper.
2. Remove the parts box and shipping boards.
3. Remove the items in the parts box. These items are shown in Figure 1.
A. Remove the bolts bag.
B. Remove the parts shown below. Parts that are used to build the SM42 are
described in the section HARDWARE at the end of these instructions.
Figure 1. Parts box contents.

SM42 Unpacking & Assembly Instructions
4
ASSEMBLY
Figure 2 shows an assembled SM42.
1
8
7
6
5
4
3
2
Figure 2. SM42 main components.
1. 1 stack cell
2. 4 stack cell
3. Lat bench
4. Connecting beam
5. Lat top
6. Tricep top
7. 300 lb. Weight stacks (1)
8. 190 lb. Weight stacks (3)
1. Place the two weight “cells” in their final resting spots. The cells will be
approximately 11’4” apart as shown in Figure 3.

SM42 Unpacking & Assembly Instructions
5
Figure 3. Set the weight stack cells.
2. Bolt on the teardrop pulleys above the benches (see Figure 4) on the 3 stack cell
using two 3/8” x 2-3/4” hex head bolts (used to bolt the cross beam to the cross
members and the adjustable pulley tops to the top beams). Include the 3/8” flat
washer, end cap washers, end caps and 3/8” Nyloc (locknut). Use the bolt
configuration shown in Figure 5. You may wish to use a pinch bar to align the bolt
holes.
3/8” x 2-3/4”
(
2
)
Figure 4. Bolt on the teardrop pulleys.

SM42 Unpacking & Assembly Instructions
6
Figure 5. Configuration for 2-3/4” and 3” bolts.
3. Bolt on the connecting beam (part 4 from Figure 2) using a 5/8” socket with
extension and combination wrench, to the cells using two of the large 7/16” x 6” bolts,
7/16” washers, and 7/16” nuts (parts A, B, and C in HARDWARE section at end of
these instructions), end cap washers and end caps (parts F and H in HARDWARE
section). Figure 6 shows the connected cells. You will need to remove the pulleys
from the teardrop pulley assemblies to gain clearance for the socket wrench
extension. Leave the pulleys out of the housings until the cables have been installed.
7/16” x 6” (6)-
mount on tops
3/8” x 3”
(
2
)
-
bolt top
beams to
g
ether
T
U
Remove pulleys from
housings to give clearance
to socket extension
Figure 6. Bolt on the connecting beam, lat top, and tricep top.

SM42 Unpacking & Assembly Instructions
7
4. Mount the 56” lat top (part T from HARDWARE section) to the 4-stack cell using a
5/8” socket and combination wrench. Insert two of the large 7/16” by 6” bolts using the
hardware configuration shown in Figure 7. Mount the 29” tricep top (part U in
HARDWARE section) to the frame and connecting beam (See Figure 7).
Figure 7. Configuration for 6” bolts.
150 lb.
weight stack
300 lb.
weight stack
150 lb.
weight stack
Figure 8. Mount the weight stacks.
5. Mount the weight stacks to the 4-stack cell. To do this:
A. Remove the tricep back rest bolts using a 9/16” socket and combination
wrench (see Figure 9).
B. Unbolt the top plate and remove the guide rods using a 9/16” socket and
combination wrench (see Figure 9).

SM42 Unpacking & Assembly Instructions
8
Figure 9. Remove the tricep back rest, the top plate and the guide rods.
C. Prepare the weight stack-
add bumpers to bottom, insert
guide rods, put pull pin in
bottom plate of stack. D. Flip over the weight stack
onto piano dolly. E. Hoist the weight
stack onto the machine.
Figure 10. Putting on the weight stacks.
C. Prepare the weight stacks. Slide the guide rods (2) through the weight stacks
(1) as shown above. Place rubber bumpers (3) on the bottoms of each guide rod.
Make sure the pull pin (4) is in the bottom weight plate.
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins
facing upward. You will need to flip the stacks over so that the pull pins are facing
outward when they are loaded onto the machine. Since the pull pins will be facing
downward when they are flipped over, it is recommended that you put the stacks
on a padded carpet to keep the pins from being damaged.
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight
stacks over the bottom plate and set the stacks onto the rubber bumpers with the
plate numbers facing outward. The 300 lb weight stacks need to be facing the
“sides” of the cells (where the benches will be attached- see Figure 9). The 190 lb
weight stacks will need to be facing the “outsides” and “insides” of the cells
(where the tricep pulley adjustable pulleys will be attached- see Figure 9). Make
sure all pull pins are facing outward.

SM42 Unpacking & Assembly Instructions
9
F. Bolt on the top plate. With the top plate on the guide rods, bolt on the top plate
to the top of the cells as shown in Figure 11 using a 9/16” socket and combination
wrench and the 3” bolts (with cap washers) that were previously inserted.
Figure 11. Bolt on the top plate.
6. Bolt the floating pulley into the 190 lb cable crossover weight stack (NOT
intended for the tricep pushdown weight stack- the one with the tricep back rest
mounted to the frame as shown in Figure 9) using a 7/8” combination wrench. You
will need to remove the pulley from the housing to thread the plug into the weight
stack bayonet. Make sure the 9/16” jam nut is threaded 1-5/8” away from the pulley
as shown in Figure 12. Leave the pulleys out since you will need to have them out
when the cable is routed.
Figure 12. Bolt the floating pulley into the 190 lb weight stack (away from the tricep
pushdown weight stack).

SM42 Unpacking & Assembly Instructions
10
7. Mount adjustable pulley brackets. When shipped, the adjustable pulley brackets
look like the ones shown in Figure 13. The bolts need to be removed and the bracket
needs to be positioned so that the top of the bracket is in the top hole as shown by
the arrow in Figure 13. Use a 3” bolt with flat washers, end cap washers and end
caps. When you remove the bolts, leave the pulley bolt and pulley out since you will
need to thread the cable with the pulley removed.
Figure 13. Mount adjustable pulley bracket.
8. Mount the seated row and lat bench to the frame. Using the bolts specified in
Figure 14 and a 9/16” socket and combination wrenches, mount the benches as
shown in Figures 14 and 15.
3/8” x 2-3/4” (4)
3/8” x 3” (2)
Figure 14. Mount the benches to the frame.